Bobrick B-169 Sidelit Mirror Installation Guide
- June 1, 2024
- BOBRICK
Table of Contents
INSTRUCTIONS FOR INSTALLATION
BOBRICK MODEL B-169 SIDELIT MIRROR
PARTS/TOOLS NEEDED:
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
Read all instructions before using this mirror.
MIRRORS SHOULD ONLY BE INSTALLED USING THE FOLLOWING INSTRUCTIONS.
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID THE WARRANTY.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to
persons:
- Turn off power before putting on or taking off parts.
- Close supervision is necessary when this mirror is used by, or near children, invalids, or disabled persons.
- Use this mirror only for its intended use as described in these instructions. Do not use attachments not recommended by Bobrick.
- This product shall be installed by a licensed electrician in accordance with local codes and regulations.
- Never operate this mirror if it has damaged wires, if it is not working properly, if it has been dropped or damaged, or dropped into water. Contact Bobrick for a replacement mirror.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Exposing the mirror edges to liquids may cause a permanent discoloration to the mirror etching that is NOT covered by Bobrick warranty.
- Electrical Specs: 100-277V | 50/60HZ | 100W Max | 1.3A Max
CLEANING INSTRUCTIONS
- Clean mirrors with warm water and a soft, lint free cloth, do not allow liquids to seep under the edges. Don’t use abrasive, acid or alkali cleaners or products with ammonia or vinegar.
- Apply mild cleaners directly to a cloth, do not spray directly on the mirror. Applying liquids directly to the mirror’s surface may allow the liquid to seep/wick between the layers on the edge of the mirror. If this occurs there may be a permanent discoloration on the mirror etching which is NOT covered by Bobrick warranty.
- Dry mirror immediately following cleaning and make sure all joints and edges are dry.
-
Mark the location of the mounting holes. See individual product specifications on page two for mounting hole locations. Two bar mirrors can only be mounted in portrait orientation.
ADA requires that “Mirrors shall be mounted with the bottom edge of the reflecting surface no higher than 40″ (1015mm) above the finished floor1.”
For lit mirrors this means the dimension is to the inner most edge of the lit portion (not required by cULus). -
Install included #14 round slotted wood mounting screws into pre-marked holes. Note, all mirrors must be installed in contractor supplied blocking. Slide the mirror assembly onto the screws.
-
Dimensional drawings
-
Wiring & Grounding Instructions
Punch out one of the three holes on the power supply box and bring in incoming AC power wires to the box. Utilize the provided Romex connectors and make all connections inside the power supply box following the wiring diagram below.
Please note, the lighting will be pre-wired to the mirror.
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system,
or an equipment grounding conductor must be run with the circuit conductors
and connected to the equipment grounding terminal or lead on the
product.
The mirror doesn’t light:
A. Check the connection between the mirror and buildings wiring.
B. Verify that there is power coming out of the power supply.
C. Verify that there is 120V power coming out of the buildings junction box.
D. Verify that the tape light has not been unplugged from the power supply.
In the United States: BOBRICK WASHROOM EQUIPMENT, INC.
200 Commerce Drive, Clifton Park, NY 12065-1350 • Telephone:
518-877-7444 • FAX:
518-877-5029
6901 Tujunga Ave., North Hollywood, CA 91605-5882 •
Telephone:818-982-9600 • FAX:
818-503-1102 or email
[email protected]
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1
Eastern Canada: 877.423.6555, Fax: 423.765.8555 • Western Canada:
877.423.6444, Fax: 423.503.8444
© 2023 by Bobrick Washroom Equipment, Inc.
Form No. 169-69_ii Revised 10/17/23