iBoard IB-P106C Polished Running Boards Style Installation Guide
- June 1, 2024
- iBoard
Table of Contents
iBoard IB-P106C Polished Running Boards Style
Product Information
Specifications:
- Part Number: IB-P106C&J
- Fastener Size: 6mm, 8mm, 10mm, 12mm, 14mm
- Tightening Torque (ft-lbs):
- 6-7 for 6mm
- 16-18 for 8mm
- 31-32 for 10mm
- 56-58 for 12mm
- 92-94 for 14mm
Product Usage Instructions
Step 1: Nut Plate Installation
Locate the front and rear mounting locations on the vehicle.
Step 2: Vehicle Preparation
For vehicles with a factory-threaded hole in the floor panel:
- Locate the front and rear mounting locations.
- Proceed to Step 3.
Step 3: Bracket Assembly
Assemble the driver-side mounting brackets and support brackets. Do not fully
tighten the hardware at this time.
Step 4: Mounting Bracket Installation
Select the assembled driver front mounting brackets:
- Vehicles with open mounting location:
- Insert an M8 Nut Plate into the large square opening in the floor panel.
- Line up the threaded nut with the small hole in line with the tab on the bracket.
- Bolt the mounting bracket to the nut plate using an M8X1.25-35mm hex bolt, an M8 lock washer, and an M8 large flat washer. Do not fully tighten the hardware at this time.
- Vehicles with a factory-threaded hole in the floor panel:
- Bolt the tab on the mounting bracket to the threaded hole in the floor panel using an M8X1.25-35mm hex bolt, an M8 lock washer, and an M8 large flat washer. Do not fully tighten the hardware at this time.
Frequently Asked Questions (FAQ)
-
Q: Do I need special tools for installation?
A: No special tools are required for installation. The necessary hardware is provided in Hardware Packages A and B. -
Q: Can I install this product without assistance?
A: While assistance is recommended, following the provided instructions carefully will allow for successful installation without additional help.
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
Size Measurement
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | √ |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY|
Description
---|---|---|---|---|---
1#| 4| M8 Nut Plates| 7#| 8| M8X1.25 Hex Nuts
2#| 4| M8X1.25-35mm Hex Bolts| 8#| 8| M6X1-25mm Inner Hex Bolts
3#| 8| M8X1.25-25mm Hex Bolts| 9#| 8| M6 Large Flat Washers
4#| 4| M8 Large Flat Washers| 10#| 8| M6 Flat Washers
5#| 16| M8 Flat Washers| 11#| 8| M6X1 Nylon Lock Nuts
6#| 12| M8 Lock Washers| | |
Hardware Package B (For Step Bar Installation)
Item| QTY| Description| Item| QTY|
Description
---|---|---|---|---|---
1#
| 8| M8X1.25-35mm Carriage Bolts| 3#| 8| M8 Nylon Lock Nuts
2#| 8| M8 Large Flat Washers| 4#| 4|
Sliders (Packed with Mounting Brackets)
Scan for Installation Video
Installation Instruction
STEP 1
Start from the Driver-side front of the vehicle. Determine if the vehicle
with open mounting locations or factory-threaded holes in the floor panel.
A. Vehicles with open mounting location:
- Insert (1) M8 Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld, (Fig 1A, 1B & 2).
- Move along to the rear mounting location, (Fig 3). Repeat Step 1a to insert the M8 Nut Plate into the rear opening on the floor panel.
STEP 2
Vehicles with factory threaded holes in floor panels:
Locate the front and rear mounting locations, (Figs 4&5). Continue to Step 3.
STEP 3
Assemble (2) Driver Side Mounting Brackets and (2) Driver Side Support
Brackets (Figs 6-7). Do not fully tighten the hardware at this time.
STEP 4
Select the assembled Driver Front Mounting Brackets.
Vehicles open mounting location:
Insert (1) M8 Nut Plate into the large square opening in the floor panel. Line
up the threaded nut with the small hole in line with the tab on the Bracket,
(Figs 8A & 8B). Bolt the Mounting Bracket to the Nut Plate with (1)
M8X1.25-35mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat Washer. Do not
fully tighten hardware at this time, (Fig 9).
Vehicles with factory threaded holes in floor panels:
Bolt the tab on the Mounting Bracket to the threaded hole in the floor panel
with (1) M8X1.25-35mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat
Washer, (Fig 9). Do not fully tighten the hardware at this time.
STEP 5
Line up the Support Bracket with the (2) factory holes on the pinch weld. Bolt
the Support Bracket to the back of the pinch weld using (2) M6X1-25mm Inner
Hex Bolts, (2) M6 Flat Wash-ers, (against pinch weld), (2) M6 Large Flat
Washers, (inside against the bracket) and (2) M6X1 Nylon Lock Nuts, (Fig 10).
Do not fully tighten the hardware at this time.
STEP 6
Move to the Driver Side Rear Mounting Location, (Fig 11A). Repeat Step 5 to
assemble Driver Rear Mounting Brackets, (Figs 12&13).
NOTE:
Determine the correct Rear Support Bracket installation procedure according to
the model/year of the vehicle:
- 2007 Model: Line up the centre hole on the Support Bracket to the pinch weld, secure by using (1) M6X1-25mm Inner Hex Bolt, (1) M6 Flat Washer (outside), (1) M6 Large Flat Washer,(inside against bracket), and (1) M6X1 Nylon Lock Nut to at-tach rear bracket to the back of the pinch weld, (Fig 12).
- 2008-UP Models: Attach the Support Bracket to the back of the pinch weld by using (2) M6X1-25mm Inner Hex Bolts, (2) M6 Flat Washers (outside), (2) M6 Large Flat Washers (inside against the bracket) and (2) M6X1 Nylon Lock Nuts, (Fig 13). Do not fully tighten the hardware at this time.
STEP 7
Once all (2) Driver side mounting brackets are installed, then proceed to the
Step Bar installation. (Figs 14 & 15)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
- Attach the Step Bar (with the Sliders) to the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 15). Do not fully tighten the hardware at this time.
Note: The Sliders are packed with the Mounting Brackets.
- Level and adjust the Step Bar and fully tighten all hardware.
- Repeat Steps 1-7 for the other side Step Bar installation. The installation is completed!
Attention
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
- To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support: info@iboardauto.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>