iBoard IB-049 Stainless Steel Black Running Boards Instruction Manual
- May 15, 2024
- iBoard
Table of Contents
iBoard IB-049 Stainless Steel Black Running Boards
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
PART#: IB-049/050C &H
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Mounting Bracket List
Item| QTY| Description| Item| QTY| Description
1#| 3| Driver Front / Center / Rear Mounting Brackets| 2#|
3| Passenger Front / Center /Rear Mounting Brackets
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-30mm Hex Bolts| 3#| 12| M8 Lock
Washers
2#| 12| M8 Flat Washers| 4#| 6| M8X1.25 Nylon Lock
Nuts
Hardware Package B (For Stainless Steel Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12|
M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders
(Packed with Step Bars)
INSTALLATION INSTRUCTION
STEP 1
Start installation at the driver side of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Fig 1 & 2).
NOTE: Remove the plastic plug or any insulation if equipped.
(Fig 1) Up To 2015 Driver Side Rear Mounting Location (Note: Remove Plastic Plug If equipped)
(Fig 2) 2016-On Driver Side Rear Mounting Location (Note: Two Factory Threaded Holes Only)
STEP 2
Attach (1) Driver Front Mounting Bracket onto the Driver Side Front Mounting Location as shown (Fig 3).
- Models with threaded stud: Attach the Mounting Bracket to the stud with (1) M8 Flat Washer, (1) M8 X1.25 Nylon Lock Nut. Next, secure the bracket to the lower threaded hole with (1) M8X1.25-25mm Hex Bolt, (1) M8 Flat Washer and (1) M8 Lock Washer. Do not tighten the hardware at this time.
- Models without threaded stud: Attach the Mounting Bracket to the upper threaded hole with (1) M8X1.25-25mm Hex Bolt, (1) M8 Flat Washer and (1) M8 Lock Washer. Next, secure the bracket to the lower threaded hole with (1) M8X1.25-25mm Hex Bolt, (1) M8 Flat Washer, and (1) M8 Lock Washer, (Fig 4). Do not fully tighten the hardware at this time.
- (Fig 3) Models With Threaded Stud Bracket Installed
- (Fig 4) Models Without Threaded Stud Bracket Installation
STEP 3
Repeat Steps 1-2 to Install the Driver Center and Rear mounting brackets.
STEP 4
Once all (3) Driver-side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5&6)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (2) sliders to the step bar.
- Attach the Step Bar (with the Sliders) to the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig
- Do not fully tighten the hardware at this time.
Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight. In order to protect your bars/boards, please use mild soap
/non-abrasive products for cleaning only.
- Customer Support: info@iboardauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>