iBoard IB-P082C Running Board 6 Black Installation Guide

iBoard®

Scan for Installation Video

iBoard® by APS

PART#: IB-P082C&J

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

*BODY FRAME MOUNT*
NO DRILLING REQUIRED**

PART LIST

Front

A: Driver Side Step Bar
B: Passenger Side Step Bar

1. Driver Front Mounting Bracket (DFM)
2. Driver Rear Support Bracket (DRS)
3. Driver Rear Mounting Bracket (DRM)
4. Passenger Front Mounting Bracket (PFM)
5. Passenger Rear Support Bracket (PRS)
6. Passenger Rear Mounting Bracket (PRM)

Hardware Package A (For Bracket Installation)

1 # 2 # 3 # 4 #

Hardware Package B (For Step Bar Installation)

1# 2# 3# 4#

STEP 1

Start installation from the driver side front of the vehicle. Remove front body mount nut and washer located underside of the vehicle.

NOTE: Use a pair of pliers or a crescent wrench to hold the bolt to loose the nut, (Fig 1).

STEP 2

Loosely attach Driver Front Mounting Bracket (DFM) using the factory nut and washer. NOTE: Keep factory rubber bushing and other factory body mount components in place (Fig 1).

(Fig 1) Driver Side Front Mounting Location

1. Factory Nut And Washer

STEP 3

Move to the Driver Side Rear Mounting Location of the vehicle. Repeat Steps 1-2 to install the Driver Rear Mounting Bracket (DRM), (Fig 2).

(Fig 2) Driver Rear Mounting Bracket Installation

1. Factory Nut And Washer

STEP 4

Locate the (2) factory threaded holes on the side panel beside the rear body mounting location. And attach the Driver Rear Support Bracket (DRS) to these factory holes by using the included (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers, and (2) M8 Large Flat Washers, (Fig 3).

Attach opposite side of Driver Rear Support Bracket (DRS) to Driver Rear Mounting Bracket (DFM) using the included (1) M8X1.25-30mm Hex Bolt, (1) M8 Lock Washer, (1) M8X1.25 Hex Nut, and (2) M8 Large Flat Washers, (Figs 3 & 4). Do not fully tighten at this time.

(Fig 3) Driver Rear Support Bracket Installed

1. DRS
2. Front
3. (2) M8X1.25-30mm Hex Bolts
   (2) M8 Lock Washers
   (2) M8 Large Flat Washers

(Fig 4) Driver Rear Support Bracket Installation

1. DRS

2. (1) M8X1.25-30mm Hex Bolt
   (1) M8 Lock Washer
   (2) M8 Large Flat Washers
   (1) M8 Hex Nut

3. (2) M8X1.25-30mm Hex Bolts
   (2) M8 Lock Washers
   (2) M8 Large Flat Washers

4. DRM

STEP 5

Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5 & 6)
(1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
(2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
(3) Slide the Slider (with carriage bolts) to the Step Bar.
(4) Repeat to install the other (1) slider to the step bar.
(5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 6). Do not fully tighten hardware at this time.

Note: The Sliders are packed with the Mounting Brackets.

Level and adjust the Step Bar and fully tighten all hardware.

Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!!

Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

(Fig 5) Slider Installation

1. Slider
2. (2) Carriage Bolts
3. Slider with (2) Carriage Bolts
4. Step Bar (Bottom View)

(Fig 6) Step Bar Installation

1. Step Bar
2. Slider (w/ installed Carriage Bolts)
3. Mounting Bracket
4. (2) M8 Large Flat Washers
   (2) M8 Nylon Lock Nuts

Customer Support:info@iboardauto.com

Rev. 20231001

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>