TARAMPS TL 500 Mini Compact Car Amplifier Instruction Manual
- June 13, 2024
- TARAMPS
Table of Contents
TL-500
Instruction Manual
The installation of this product must be made by a qualified professional.
Term of warranty
TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo
Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against
any defects on terms of project, making, assembling, and/or with solidarity,
due to project vices which cause it improper or inadequate to its original use
within 12 months from the date of purchase. In case of defect during the
warranty period, TARAMPS responsibility is limited to the repairing or
substitution of the device of its own making.
This warranty excludes:
- Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
- Warranty card is not properly filled or torn;
- Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical assistance
For international support, check on our website: www.taramps.com.br/en
/rede-de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br
Introduction
Read this manual before preparing the product. In case of doubt, contact our
technical support: (18) 3266-4050 or
www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in
household waste. Look for an electronic equipment collection or recycling
center for proper disposal.
Declaration of Conformity
**** TARAMPS ELECTRONICS LTDA Alfredo Marcondes – SP Brazil
Hereby, Taramps Electronics Ltda declares that the product TL 500 complies
with the Directive 2014/30/EU, according with the following harmonized
standard:
-EN 50498:2010 Electromagnetic compatibility (EMC) – Product family standard for aftermarket electronic equipment in vehicles
The full text of the EU Declaration of Conformity is available at the
following Product Page on Internet.
Safety requirements
To ensure proper use, please read through this manual before using the
amplifier. It is specially important that you know the WARNINGS and CAUTIONS
contained here.
– The installation of this amplifier must be done by a qualified professional.
– Wear safety glasses, insulated gloves and correct tools for installing this
product.
– This amplifier is for use with 12V batteries. Always check the voltage
before installing.
– This amplifier must be installed in a firm place with at least 1” space
around the heasink for proper heat spreading.
– Never install the amplifier in places exposed to dust, humidity and water.
Pay attention to install it far from fuel tank, fuel lines, heat sources and
other parts of vehicle.
– Be sure to install protection fuse or a circuit braker near to battery.
Follow the ampere rating as indicated here in this manual. Use of improper
fuse or circuit breaker could result in overheat, smoke, damage to product,
injury or burns.
– Avoid running wires over or through sharp edges. Use rubber or plastic
grommets to protect any wires routed through car’s body.
– Before make any connection to amplifier, disconnect the battery negative
terminal.
– When in use, the external surface of may amplifier becomes hot. Avoid
touching the heatsink area and keep childrens far from the amplifier.
– This amplifier may produce high sound pressure levels. Avoid continuous
exposure to levels over 85dB to prevent permanent hearing loss.
– Output connections for speakers may have voltage levels when the amplifier
is operating. Make sure that the amplifier is turned OFF before proceed any
connection or disconnection in this terminals.
– If you want to dispose this amplifier, don’t throw it on domestic waste. It
must be collected by an used electronic product disposal service for proper
recycling.
**** Safety
As you read this manual, pay attention to the safety symbols.
CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of
important instructions. Failure to heed the instructions will result in risk
of injury to user or product damage.
Taramps reserves the right to modify the contents of this document at any time
without prior notice and does not have the obligation to apply the changes in
units which were previously produced.
Installation
CAUTION
CAUTION: All connections to power supply, input and output connectors must
be carried out only with amplifier off.
Recommended wire gauge & fuse
Positive / negative power supply cable _15
AWG
Output cables wire gauge___15 AWG
Protection fuse or circuit
breaker_____20A
Calculated considering a maximum length of 4m. Distance greater than this, you
will need to increase the cable gauges.
Using wire gauges below the recommendation will result in power loss and
overheating of wiring.
CAUTION
Check polarity and never reverse power supply cables due to the risk of damage
to the amplifier. It is compulsory to install a protection fuses or circuit
breakers as close as possible from batteries.
The TL 500 amplifier has a feature that turn on the amplifier automatically
based on audio level at the inputs. n order to keep the amplifier working, 2
minimum sound volume is needed, around 2 to § volume units on head unit it may
vary according the song or head unit model). Ifyou turn on your head unit with
volume 0 o mute, the amplifir will tay OFF.
After turn offthe head unit, the amplifie will remain ON by about 30 seconds
Note: In case of compression divers and tweeters you must instal a
passive filer in the positive terminal of the same ones (Consult transducer’s
manufacturer manual).
Technical features
| minimum umlaut impenaance: | 2 Ohms |
|---|---|
| Number of Channels: | 2 |
| Output Power: | 90W RMS (2 x 45W RMS) |
| Supply Voltage: | 8 – 16VDC |
| Max. Musical Consumption: | 3.8A |
| Max. Sinusoidal Consumption: | 7.6A |
| Frequency Response (Full Range): | 80Hz – 40KHz (-3dB) |
| Input Impedance: | 1K Ohm |
| Protection System: | Output Overload / Thermal Protection |
| Dimensions (W x H x L): | 89 x 29 x 119mm (3.50″ x 1.14″ x 4.69″) |
| Weigth: | 0,1Kg (0.221b) |
*Power measured at 1KHz, resistive load at nominal impedance, with THD less than 10% and supply voltage = 14.4VDC.
– Due to natural tolerances of internal components and manufacturing process,
technical features may vary.
For further informations or questions please refer to the instruction manual
or contact TARAMPS support.
8 55153266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNP)/TAX ID: 11.273.485/0001-03
R Jodo Silvério, 121
– Res. Manoel Martins
Alfredo Marcondes – SP
Indiistria Brasileira – Made in Brazil
www.taramps.com.br
Documents / Resources
|
TARAMPS TL 500 Mini Compact Car
Amplifier
[pdf] Instruction Manual
TL 500 Mini Compact Car Amplifier, TL 500, Mini Compact Car Amplifier, Compact
Car Amplifier, Car Amplifier, Amplifier
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>