iBoard IB-P123C Running Boards Style Instruction Manual
- June 1, 2024
- iBoard
Table of Contents
iBoard IB-P123C Running Boards Style
Specifications
- Part Number: IB-P123C&J
- Rocker Panel Mount
- No drilling required
Product Parts List
| Item | Qty | Description |
|---|---|---|
| 1# | 2 | Driver / Passenger Front Mounting Brackets |
Product Usage Instructions
- Step 1: Locate Threaded Holes
- Starting from the driver side of the vehicle, locate the factory-threaded holes at the bottom of the outer frame channel and the single-threaded hole at the bottom of the inner frame channel.
- Step 2: Assemble the Front Mounting Bracket
- Assemble the Driver Front Mounting Bracket and Driver Front Support Bracket using the provided bolts and nuts. Do not fully tighten the hardware at this time.
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
PART#: IB-P123C&J
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | √ |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package A (For Bracket Installation)
| Item | QTY | Description | Item | QTY | Description |
|---|---|---|---|---|---|
| 1# | 2 | Driver / Passenger Front Mounting Brackets | 8# | ||
| 4 | M10 Lock Washers | ||||
| 2# | 2 | Driver / Passenger Front Support Brackets | 9# | ||
| 4 | M10X1.5 Hex Nuts | ||||
| 3# | 1 | Driver Rear Mounting Bracket | 10# | 8 |
M8X1.25-20mm Hex Flange Bolts
4#| 1| Passenger Rear Mounting Bracket| 11#| 8|
M8X1.25 Hex Flange Nuts
5#| 4| M10X1.5-35mm Bolt Plates| 12#| 6|
M8X1.25-30mm Hex Bolts
6#| 4| M10 Plastic Washers| 13#| 6| M8 Flat
Washers
7#| 4| M10 Flat Washers| 14#| 6| M8 Lock Washers
Hardware Package B (For Step Bar Installation
INSTALLATION
STEP 1: Starting from the driver side of the vehicle, locate the (2)
factory-threaded holes at the bottom of the outer frame channel and the
single-threaded hole at the bottom of the inner frame channel, (Fig 1A & 1B).
NOTE: The threaded holes may be filled with plastic plugs or filled with
insulation. Remove plugs or insulation before proceeding.
(Fig 1A) Driver Side Front Mounting Location (Two Threaded holes on the outer
frame channel)
(Fig 1B) Driver Side Front Support Mounting Location (One threaded hole on the inner frame channel)
STEP 2: Assemble (1) Driver Front Mounting Bracket and (1) Driver Front Support Bracket together with the included (4) M8X1.25-20mm Hex Flange Bolts and (4) M8X1.25 Hex Flange Nuts, (Fig 2). Do not fully tighten hardware at this time.
STEP 3 : Position the assembled driver front brackets to the vehicle. At- tach the Driver Front Mounting Bracket to the (2) threaded holes (Fig 1A) by using the provided (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Flat Washers, (Fig 3).
Line up the slot at the end of the Support Bracket with the threaded hole on the inner frame channel. Bolt the Support Bracket to the threaded hole on frame channel (Fig 1B) with (1) M8X1.25-30mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Flat Washer, (Fig 3). Do not fully tighten the hardware at this time.
STEP 4
Move to the Driver Side Rear Mounting Location on the body panel, (Fig 4).
Thread (2) M10 Plastic Washers onto (2) M10X1.5-35mm Bolt Plates. Insert the
M10 Bolt Plates with Plastic Washers into the oval hole, and thread the
Plastic Washers down against the body panel, (Fig 4). Rotate the M10 Bolt
Plates 90 degrees to across the slot in the body panel.
IMPORTANT: The Plastic Washer is designed to prevent the M10 Bolt Plate from falling into the body cavity within the Bracket installation.
STEP 5: Select (1) Driver Rear Mounting Bracket. Hang the Bracket onto the installed (2) M10 Bolt Plates and secure with (2) M10 Flat Washers, (2) M10 Lock Washers and (2) M10 Hex Nuts, (Fig 5). Do not fully tighten hardware at this time.
STEP 6: Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 6 & 7)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
- Attach the Step Bar (with the Sliders) to the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 7). Do not fully tighten the hardware at this time.
Note: The Sliders are packed with the Mounting Brackets.
- Level and adjust the Step Bar and fully tighten all hardware.
- Repeat Steps 1-6 for the other side Step Bar installation. The installation is completed!!!
Attention
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
- To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support: info@iboardauto.com
Scan Installation Vedio
Frequently Asked Questions
- Q: Is drilling required for installation?
- A: No, drilling is not required as this product is designed for rocker panel mount without drilling.
- Q: What is the recommended tightening torque for different fastener sizes?
- A: The recommended tightening torque is as follows:
- 6mm: 6-7 ft-lbs
- 8mm: 16-18 ft-lbs
- 10mm: 31-32 ft-lbs
- 12mm: 56-58 ft-lbs
- 14mm: 92-94 ft-lbs
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>