BEGA 85 162 Performance Floodlight Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

Performance floodlight
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 85 162 Performance Floodlight Instruction Manual

Performance floodlight

Instructions for use

Application
Performance floodlight with G½ mounting bush.
The floodlight can be bolted together with any female thread G½ according to ISO 228 supplied by others or to BEGA accessories.
For a variety of interior and exterior lighting applications.

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Clear safety glass
Silicone gasket
Reflector surface made of pure aluminium
BEGA Hybrid Optics®
Rotation range of floodlight 350°
Swivel range – 30°/+95°
Mounting bracket with G½ threaded
connection
Thread length: 14mm
Connecting cable X05BQ-F 5G1mm²
Cable length 1m
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Conformity mark
Wind catching area: 0.053 m²
This product contains light sources of energy efficiency class(es) E

Lighting technology

Symmetrical wide beam light distribution
Half beam angle : 47°
For special lighting applications, an optical filter can be used to change the symmetrical light cone into a flat beam light distribution.

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website atwww.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.

Installation

Screw the floodlight G½ threaded connection firmly into the on-site G½ female thread or
BEGA accessory.
G½ threaded connection torque = 40Nm.
Secure the screw connection from loosening on site (if provided with locking screw S, see fig. A).
Check the earth conductor connection between the G½ threaded connection and the on-site G½ female thread.

Adjust floodlight:

Undo hexagon socket screw (wrench size
6 mm) and hexagon nut (wrench size 30 mm) and set the desired beam direction.

Torque:
Hexagon socket screw = 12 Nm
Hexagon nut = 35 Nm
Secure bolted connection Gß against loosening by tightening the hexagon socket screw (wrench size 2 mm, see sketch B ).

The electrical connection must be carried out with matching protection class and safety class, strain-relieved, with suitable connection terminals (not included in the scope of delivery) at the luminaire power supply cable.
Note correct configuration of the mains supply cable. The earth conductor is connected at the green-yellow (1), the phase to the brown
(L), and the neutral conductor to the blue (N) marked wire.
The connection of the control cables is achieved by means of the both leads marked with DALI. In case these leads are not used the luminaire will be operated at full light output.

Lamp
Module connected wattage 96.4 W
Luminaire connected wattage 108 W
Rated temperature ta=25 °C
Service life criteria 50000 h/L70
85 162K3
Module designation 4x LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 13400 lm
Luminaire luminous flux 8791 lm
Luminaire luminous efficiency 81,4 lm/W
85 162K4
Module designation 4x LED-0800/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 13600 lm
Luminaire luminous flux 8922 lm
Luminaire luminous efficiency 82,6 lm/W

Cleaning · Maintenance
Clean luminaire regularly with solvent-free
cleansers from dirt and deposits.
Do not use high pressure cleaners

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module
The designation of the LED module is noted
on a separate label in the luminaire or on the
underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Open the floodlight:
Undo locking pin (hexagon socket head wrench size 2.5 mm) on the back side of the floodlight housing.
Remove the trim ring along with the safety glass and reflector by twisting it counterclockwise.
Replace LED module.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Place trim ring with glass and reflector on the floodlight housing in such a way that the notches in the trim ring and floodlight housing align on top to each other.
Twist on the trim ring clockwise as far as the stop. Tighten locking pin.

Accessories

71 292 Optical filter flat beam
71334 Shield
71 339 Cylindrical shield
70 214 Pole cap for pole top ø48mm
70 248 Pole cap for pole top ø60mm
70 249 Pole cap for pole top ø76mm
70 229 Pole cap for pole top ø82mm
70 245 Mounting box · rectangular
70 280 Tube clamp
70 379 Cross beam
70 889 Lashing strap
For the accessories a separate instructions for use can be provided upon request.

Spares

Trim ring graphite with glass : 25 000 301
Trim ring silver with glass : 25 000 302
LED power supply unit : DEV-0363/700
LED module 3000 K : LED-0800/930
LED module 4000 K : LED-0800/940
Reflector : 75 004 937
Gasket housing : 83 001 780
Gasket trim ring : 83 002 225