70mai UP04 4G Hardwire Kit User Manual

4G Hardwire Kit
User Manual

UP04 4G Hardwire Kit

Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use and keep this user manual for future reference. Pay particular attention to the safety instructions. If you have any questions or comments about the device, please
contact the customer line.
✉ www.alza.co.uk/kontakt
✆ +44 (0)203 514 4411
Importer Alza.cz a.s., Janko Cova 1522/53, Holozoic, 170 00 Prague 7, www.alza.cz

Product overview

Please read tis manual carefully before using the product and keep it in a safe place.

1. Reset button
2. Indicator
3. SIM Card Slot
4. Type-C port
5. Adhesive sticker
6. Power wire (Red)
7. Ground wire (Black)
8. ACC Signal wire (Yellow)
9. Type-C connecting cable

If the product stops responding, press and hold this button to reset it.
Note: Illustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to product enhancements.

Product functions

As and accessory to 70mai in-car devices, thus product must be used with the main device. After correctly installed and bound in the 70mai app, this product provides the following features:

• Provide power source to the main device.
• Provide Internet service to the main device (When installed with a SIM card)
• Detect the ACC OFF signal when the car engine is turned off, so that the main device will enter parking surveillance mode (Parking surveillance function needs to be enabled in the main device beforehand)
• Provide low-voltage protection to prevent over-discharging of the car battery due to the continuous operation of the main device.

Installation

Step 1. Selecting the suitable fuse box
Select a suitable car fuse box that contains the following fuses:

• Regular electric fuse with and output voltage of 12-30V.
• ACC power fuse.

Step 2. Connecting the hardwire kit to the fuse box
Connect the wires of the hardwire kit to the fuses inside of the fuse box in the following way:

1. Connect the power wire (Red) to the regular electric fuse with an output voltage of 12-30V.
2. Connect the ACC signal wire (Yellow) to the ACC power fuse.
3. Connect the ground wire (Black) to the negative terminal or ground of the fuse box.
   Note: Before installation and wiring, please turn off the car engine and power to prevent short circuit.

Step 3. Testing circuit and ACC signal
Test circuit and ACC signal in the following way:

1. Insert the L-shape plug of the connecting cable to the Type-C port of the hardwire kit, and the other plug into the power port of the main device. Start the card engine and wat for the main device to turn on. If the main device fails to power on, turn it on manually. If the message “Connect to an external power source” is shown, check if the power wire of the hardwire kit is correctly connected to the regular electric fuse.
2. After the main device is turned on, turn off the engine and remove the key. Check If the main device powers of or enters sleep mode. For some cars, the ACC power off signal will only be triggered when the driver seat door is opened after the engine is turned off. Some card models will only trigger the ACC power off signal after the engine has been turned off for a certain period of time. For such cars, check if the main device powers off or enters sleep mode after the ACC power is turned off.
3. After the main device power off or enters sleep mode, restart the engine and check if the main device automatically turn on. If the above steps can be proceed correctly, the circuit and ACC signal test is passed. If the circuit and ACC signal test fails, please check the wiring of the hardwire kit and ensure that the fuse and ground are correctly connected. If the connection is correct but the test fails contact after-sales service for assistance.

Step 4. Managing cables

1. Managing the Type-C connecting cable Route the Type-C connecting cable along the A pillar, top of the windshield to the main device.
   You can use the wiring crowbar bar to hide the cable underneath the vehicle’s headliner and rubber seal along the A-pillar.

2. Managing the hardwire kit
   Route the hardwire kit along the gap between the console centre and the A pillar to the fuse box.
   If the hardwire kit is too long, tie it up, but do not cut it off. Cutting the hardwire kit will affect the power and ACC signal to the main device.
   Note: The location of the fuse box and the recommended mounting position (position 1 or

2. of the main device may vary from vehicle to vehicle. Please employ a professional technician for mounting according to the vehicle condition. The illustration provided is for reference only.

Binding the hardwire kit

This product needs to be bound in the 70mai app so as to provide the Internet service to the main device. Before binding, prepare the followings:
Inserting the SIM card
When the engine is turned off, insert the SIM card into the SIM card slot of the hardwire kit.
Connecting the hardwire kit and the main device
Refer to the Installation chapter in this user manual, correctly install the hardwire kit and connect it to the main device through the connecting cable.
After the preparations, follow the steps below to bind the hardwire kit.

1. Park the car in a place where your phone’s Internet signal is good. And then start the car to turn on the main device.
2. Add the main device in the 70mai app following the user manual and user guide of the main device.
3. Open the 70map app and enter the plug-in page of the main device, and tap 4G module.
4. Bind the hardwire kit following the instructions on the screen. The main device’s network service will be available once the hardwire kit is bound successfully.

Note: During the binding, keep your phone close to the main device without obstacles in between.

Precautions

Before using the device, please read all the precautions to ensure correct and safe use.

• Please ask a professional technician to perform the installation. Our company is not liable for any short-circuiting of the car power supply and damage to car battery or interior due to improper installation.
• Our company is not liable for any losses resulting from the installation of the product unless they are caused by product quality issues.
• The performance of this product is affected by the reliability of the car power source, car battery and main device. Our company is not liable for any losses from the malfunction of this product unless it is caused by product quality issues.
• Some cars cannot detect changes in ACC signals when the engine is turned on or off. For such cards, the hardwire kit is unable to transmit ACC signals to the main device. This may cause certain functions to be unavailable.
• Please only use this product for legal purposes.

Specifications

Packing list

• 70mai 4G Hardwire Kit x 1
• Type-c connecting cable x 1
• Pin x 1
• User Manual x 1

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for which the claimed claim may not be recognized:

• Using the product for any purpose other than that for which the product is intended or failing to follow the instructions for maintenance, operation, and service of the product.
• Damage to the product by a natural disaster, the intervention of an unauthorized person or mechanically through the fault of the buyer (e.g., during transport, cleaning by inappropriate means, etc.).
• Natural wear and aging of consumables or components during use (such as batteries, etc.).
• Exposure to adverse external influences, such as sunlight and other radiation or electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic discharge voltage (including lightning), faulty supply or input voltage and inappropriate polarity of this voltage, chemical processes such as used power supplies, etc.
• If anyone has made modifications, modifications, alterations to the design or adaptation to change or extend the functions of the product compared to the purchased design or use of non-original components.

EU Declaration of Conformity

Identification data of the manufacturer’s / importer’s authorized representative:
Importer: Alza.cz a.s.
Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7
CIN: 27082440
** The manufacturer hereby, declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments. The fill text of the EU declaration of conformity is available at the following internet address:
https://help.70mai.asia./1993.html
WEEE
** This product must not be disposed of as normal household waste in accordance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE – 2012/19 / EU). Instead, it shall be returned to the place of purchase or handed over to a public collection point for the recyclable waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in fines in accordance with national regulations.

References

• Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
• alza.at
• Alza | Alza.co.uk
• alza.de
• alza.hu
• alza.sk
• Could’t connect to the app

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>