DARANENER NEO 1500 Pro Power Station User Manual
- May 15, 2024
- DARANENER
Table of Contents
DARANENER NEO 1500 Pro Power Station
Important Safety Instructions
Please keep this “Instruction Manual” in a safe place.
This manual contains installation, operation, and instructions for the
DaranEner Power Station NEO1500 Pro.
WARNING – When using this product, basic precautions should always be followed, including the following:
- Read all the instructions before using the product.
- Do reduce the risk of injury, close supervision is necessary when the product is used near children.
- Do not put your fingers or hands into the product.
- Use of an attachment not recommended or sold by the power pack manufacturer may result in a risk of fire, electric shock, or injury to persons.
- Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
- Do not operate the power pack with a damaged cord or plug, or a damaged output cable.
- Do not disassemble the power pack, take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.
- To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed servicing.
WARNIN G- RISK OF EXPLOSIVE GASES.
- To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary markings on these products and on the engine.
- When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause an explosion. The temperature of 130°C can be replaced by the temperature of 265 ° F.
- Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
- Attach output cables to a battery and chassis as indicated below. Never allow the output clamps to touch one another.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This product is equipped with a cord having an
equipment grounding conductor and a grounding plug. The plug must be plugged
into an outlet that is properly installed and grounded under all local codes
and ordinances.
WARNING – Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product- if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Cautions
- Before the equipment is connected to the power station, please confirm whether the equipment parameters are consistent with the power station nameplate parameters.
- Please ensure that no short circuit is caused when connecting the power station.
- The power must be disconnected when cleaning or maintaining the charger adapter after use.
- Children can not aware of the dangers of electrical equipment, please place the power station out of the reach of children.
- Do not put any objects (especially metal objects) into the power station through the heat sink or interface.
- Do not replace or modify the battery pack.
- Do not touch the metal part of the DC and AC interface without protection.
- Please place the power station in a dry place, do not place the power station in a corrosive, acid-base, flammable & explosive gas, dusty, rainy, or humid environment. Please ensure adequate ventilation during use, always maintain at least 5cm of ventilation space around the power station. Ensure that flammable and explosive objects are kept away from the power station.
- Do not drop or place heavy objects on the product. Please avoid strong shocks to the product.
- When the device is not used for a long time. Please make sure to charge the power station at least every 30 days, to ensure the cycle life of the battery pack.
- Please do not overcharge the product. Please disconnect the power supply immediately after fully charged.
Use Instructions
Parts Name & Function
Panel Function
- AC Output Port: For matching AC output voltage devices.
- Overload Protection Switch: When the external device is disconnected after exceeding the overload protection, after removing the overload devices, simply press the button of the overload protection switch back manually to reset.
- AC Input Port: AC input cable connection socket.
- XT60 Input Port: To charge the internal battery pack by the Solar energy input port.
- LED Display: Showing working statuses and parameters.
- USB-C Port 2: Support PDlOOW (20V/5A} output. Compatible with various PD protocol devices.
- DC Switch Button: Long press until the LED screen lights up (about 3 seconds} to activate the USB, DC5521, and cigarette lighter output. Short press again to close all DC outputs. When the DC output is activated, long press the DC button for 10 seconds to reset the DC board.
- USB-C Port 1: Support PDlOOW (20V= 5A} output. Compatible with various PD protocol devices. This USB-C port supports DC board firmware upgrades.
- USB A Port: From right to left are Al-A4 ports. Support QC3.0 fast charging when each port is used alone. 5V/2.4A when used at the same time.
- DCSS21Output: DC5521 output socket x4 with DC12V= lOA output.
- Cigarette Lighter Output Female Socket: DC12V= lOA output for cigarette lighter device.
- AC Switch Button: Long press the AC switch for 1 second to activate the AC output. Short press to turn off the AC output.
- Ambient Light: This decorative light bar lights up with the power station working status by default, and can be switched on and off by DC buttons.
- LED Light Bar: With 2 levels of brightness, flashing mode, and SOS mode.
- LED Light Button: Long press for 1 second to light up (100% brightness), short press to switch between 50% brightness, flashing mode, and SOS mode. Press again to turn off the LED light.
LED Screen Display
-
Low Temp Indicator: This icon will light up when working at a low temperature.
-
High Temp Indicator: When the temperature inside the machine reaches the temperature protection threshold, the device will turn off the output, and this icon will light up.
-
Alarm Indicator: This icon will light up when the device is malfunctioning. (This icon won’t light up when the battery pack has not malfunctioned.
-
Solar Charging Indicator : This icon will light up when the solar panel is connected.
-
Hibernation Indicator: This icon will light up when the hibernation mode is on.
Note: When hibernation mode is turned off, you can charge the devices for a long time or charge devices with low power, such as for shooting time-lapse movies, or charging wireless earbuds. -
Power Percentage Indicator: The battery power level icon.
-
AC Output Voltage and Frequency Display Icon : The icon lights up when the corresponding voltage and frequency are output. For example, when the output is 120v/60hz, the icons for 120V and 60hz will light up on the screen.
-
Power Indicator: Each block represents 20% of the battery power.
-
USB Indicator: This icon will light up when the USB output is activated.
-
DC Indicator: This icon will light up when the DC output is activated.
-
Input Power: Displays the current input power.
-
IN Indicator: The input icon will light up when charging.
-
Charge/Discharge Time : The remaining charging time is displayed when charging, and the remaining dischargeable time is displayed when discharging.
-
Output Power : Displays the current output power
-
OUT Indicator: The output icon will light up when AC/DC output is activated.
-
LED Light Indicator: When the LED light is activated this icon will light up at the same time.
-
AC Indicator: This icon will light up when the AC output is activated.
Operating Instructions
Power-on Operation
Please long press the AC/DC/LED button to turn on the corresponding
function according to you meeds.
DC Button
Long press the DC output button to enable the power output of USB-A and
USB-C ports, cigarette lighter socket, and DC output port. The DC icon and USB
icon on the LCD screen will light up at the same time. Short press the button
to turn off all DC outputs. If the DC power is on, press and holds the DC
button for IO seconds to reset the DC board.
AC Button
Long press the AC button the AC icon on the LED screen and the
corresponding working voltage frequency icon will light up. At the same
time,AC power output is available.
LED Light Button
Press and hold for 1 second to turn the light on (100% brightness), then
short press to switch to 50% brightness, the second short press to switch to
fast flashing, and the third short press switches to SOS flashing signal. And
the last short press will turn off the LED light.
Ambient Light Function Setting
The ambient light is on by default, and if you want to turn off the ambient
light, press and hold the DC button for seconds while the DC power is on to
turn off the ambient light. Repeat the above steps if you need to restore
ambient light.
Controlled by a combination of DC and LED buttons ©Hibernation Mode
The hibernation mode is set by default, and the hibernation mode is valid
for a long time after being set. Under hibernation mode, the DC output, and
USB output will automatically turn off after 15 minutes with no load (current
of less than 200mA), and the AC output will automatically turn off after about
8 hours with no load. Hold the DC switch button and press the LED button can
turn off the hibernation mode, the hibernation icon on the LED screen will
turn off, which means that the power will not automatically turn off when
there is no load(Leaving the power station unloaded for a long time may cause
the battery to run out). Repeat the operation above to restore the hibernation
mode.
Deep Sleep Mode
When hibernation mode is turned on, the power station will automatically
enter deep sleep mode 2 hours after turning off the power output completely.
In deep-sleep mode, the power station itself consumes very little power. To
prevent deterioration of the battery, and to prevent the power station from
running out of power after long-term storage due to the power consumption of
the power station itself, please charge the power station to full and activate
the hibernation mode before long-term storage or transportation.
- With the DC/AC power on, long press the DC button for 15 seconds to enter deep sleep mode directly. (At least 30 seconds are required before the next restart after this operation. Suitable for transportation and long-term storage.)
AC Frequency Switching
Support 120Voutput inverter. The default AC frequency is set to 60Hz.
First, turn on the power of all outputs, press the DC button+ LED button at
the same time for 3 seconds to switch the frequency, and the corresponding
frequency icon on the LED screen will blink. After switching the AC frequency
from SO Hz to 60Hz, the icon stays lit.
Power off Operation
The no-load power consumption of N EOlS00 Pro is about 7W. When the power
station is in a no-load state, please press each button to turn off the
corresponding working state to prevent power loss.
Device Connection
If the power of the connected device exceeds the limit of the output of
this unit, the power will be automatically cut off. Please confirm that the
power consumption of the device is compatible with the specification of the
power station before connecting the devices to the power station.
ChargingYourPowerStation
Please strictly follow the instructions below to charge the power station.
Charge the product only when the environment temperature is 0°C-40°C. Please
use the original charging cable. To extend battery life, when charging is
complete and the battery level shows 100%, continue charging for 30 minutes
before disconnecting the charging power source.
Note: To extend battery life and safety, please cool down for 2-3 hours after full power discharge before charging.
Charging with an Original AC Cable
Charge the power station using the AC cable provided by DaranEner. The charging voltage is 120V 60HZ. Super-fast charge from 0% to 100% takes about 1.8 hours.
ChargingwithSolarPanel
- Place the solar panel in a place where it can get enough direct sunlight and adjust the solar panel to an appropriate angle.
- Connect the solar panel to the power station XT60 input port.
Warm tip: The actual charging efficiency of the solar panels depends on various factors such as weather, temperature, sunlight, the angle of the solar panel, etc. The actual solar charging efficiency may be different.
Cold Climate Use Method
- Due to the chemical characteristics of Lifepo4 batteries, low temperatures { -10~-40°C) will affect the battery capacity of the product. If you are in an environment below 0 °C{32°F), it is recommended to place the power station in an insulated container and connect it to a charging power source{AC input/solar panel, etc.). The natural heat generated by the power station in the insulated container will keep the battery pack efficiency at the highest level.
- In an environment below DC {32°F), the power station cannot be charged but can output power to other equipment.
Discharge protection
To extend battery life, the BMS (Battery Management System) will automatically
turn off the AC output when the battery level is below about 7%, and can only
use DC output. When the battery level is about 7%, using AC output may
activate the over-discharge protection and all power will be automatically
turned off.
Troubleshooting
Product Specifications
Cell specifications
Input and Output
Basic Specifications
Product Warranty
Warranty Policy
- Claiming a warranty may need your receipt and order number. We may also need to verify your identity.
- We provide 2 years warranty for all DaranEner products, you can extend the warranty to 5 years by registering as a user on DaranEner’s official website.
- During the warranty period, we will provide free repair or replacement service.
- Even if the product warranty has expired, we can still provide paid support. However, we may not be able to handle peripherals ( such as cables), discontinued products, or parts.
- We have a DOA ( Defective on Arrival) period of 7 days. This means that if the product becomes defective within seven days of receipt. we will replace the item free of charge.
- Even within the warranty period, if the product is damaged due to negligence such as customer disassembly, water immersion, drop, etc, or damage caused by natural disasters, this is not within the scope of free maintenance. The maintenance fees and freight will be charged.
- Products purchased from non-genuine channels such as resale second-hand products or products purchased from unknown sources are not covered by the warranty and will not be repaired. In this case, please contact your seller for warranty support.
Disposal and Recycling
- This product has a built-in LiFePo4 battery and cannot be disposed of with general household waste.
- These are hazardous materials and are subject to certain transportation and disposal regulations.
- Do not open or disassemble this product and recycle its battery alone.
- When disposing of this product, please follow the instructions of your local government and dispose of it under the prescribed method.
Packaging List
FAQ
-
Q: What type of battery does DaranEner N EO1500 Pro use?
A: NEOlS00 Pro adopts a new generation of LiFeP04 battery, which is high safety, long life, and good heat resistance -
Q: What should I do if there is a malfunction?
A: Please contact customer service for troubleshooting. Do not disassemble the product by yourself. -
Q: Does NEO1500 Pro use the MPPT method to charge?
A: NEOlS00 Pro uses MPPTsolarcharging. -
Q: Can I charge other devices at the same time when the power station is charging?
A: Yes, NEOlS00 Pro supports the UPS function. If the power consumption required by the connected external device exceeds the power supply of the internal battery, the AC charging input will power the connected external device first, suspending the charging of the power station. In the event of a sudden power failure, the UPS function can switch the mains to the internal battery power within 20. -
Q: When the AC output is on, the AC outlet is not connected to the external devices, will it drain battery power in this situation?
A: When the AC output is turned on, the inverter will be started, and there is a no-load power consumption of less than! OW. When the power station is not in use, please close each output interface to prevent battery power drained out. -
Q: After fully charging the power station and storing it for a long time without use, how long will the battery drop to 0%?
A: When NEOlS00 Por is not in use, there is almost no natural discharge ( turning off all switches). If it is stored for a long time after being fully charged, it can still retain more than 80% of the power after 3 months. If for emergency backup use, please check the remaining power at least every 3 months. -
Q: When using the AC output, there is obvious noise, is it a malfunction?
A: It is not a malfunction. This is the sound of the cooling fan running. The fan dissipates the internal heat and keeps the battery working in a good temperature environment. -
Q: Can this power station be brought on the plane?
A: NEOlS00 Pro cannot be carried on aircraft or shipped by air. -
Q: After using it for the firsttime or using a time, the remaining battery power displayed on the LED screen is different from the actual remaining battery power, or the battery is draining too fast?
A: The remaining power displayed on the LED screen may differ from the actual remaining power after the first use or after a period of long-term use. If this happens, don’t worry. This is because the BMS goes into learning mode. After the first use or use for a long period, the battery pack needs to be fully charged and discharged twice so that the BMS can re-learn and correct the battery power level.DaranEner is working hard to improve the accuracy of the displayed data Specific operation steps:- Use (fully discharge) the power station to 0%
- Then charge the battery to 100% leave it for 3 hours or more, and fully discharge again (Repeat the above discharge and charge operations twice).
If the problem persists, please contact customer service.
-
Q: Why does NEO1500 Pro not support car cigarette lighter charging?
A: NEOlS00 Pro uses an MPPT charge and discharge controller. The rated input voltage of the XT60 port for solar charging is 33-60V. The car cigarette lighter can only provide 12V/24V charging voltage. Therefore, the XT60 interface of N EOlS00 Pro does not support charging from the car cigarette lighter socket. If you want to charge the NEOlS00 Pro through your car’s cigarette lighter socket in an emergency, you can charge the NEOlS00 Pro from the car battery by connecting the included charging cable to a car cigarette lighter inverter/converter ( Note: the car inverter /converter is not included in the package, please buy it separately).
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1 )this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful·, interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/V technician for help with an important announcement
Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
CONTACT
DARANENER
- Website : https://www.daranener.com
- Email: support@daranener.com