nedis PIP100012EBK 1000 Watt Pure Sine Wave Power Inverter User Guide

nedis PIP100012EBK 1000 Watt Pure Sine Wave Power Inverter User Guide

ned.is/pip100012ebk

Quick start guide

Power Inverter (1000/2000 Watt)

PIP100012EBK PIP100012FBK
PIP100024EBK PIP100024FBK
PIP200012EBK PIP200012FKB
PIP200024EBK PIP200024FBK

For more information see the extended manual online: ned.is/pip100012ebk

Intended use

This product is a power inverter to convert 12/24 V DC to 230 V AC.

Check the specifications of your model.
Only use this product in combination with class II devices.
Do not use this product with:

• Devices that exceed the rated power of the inverter.
• Capacitive and perceptual load devices such as air conditioning, high power drills, fridges, microwave ovens, or blenders.
• Devices that have strict power supply requirements, such as precision measuring equipment.

The product is intended for indoor use only.
Any modification of the product may have consequences for safety, warranty and proper functioning.
The product is not intended for professional use.

Main parts (image A )

1. Power inverter
2. Power cables
3. Remote
4. Remote cable

Main parts (image B )

1. Cable terminal –
2. Cable terminal +
3. Ground
4. Power socket
5. Remote port
6. USB port
7. USB-C port
8. Power switch
9. Fault indicator LED
10. Power indicator LED

Safety instructions

WARNING

• Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.
• Only use the product as described in this document.
• Do not install the product next to flammable materials.
• Do not place the product in areas with high temperature or direct sunlight.
• Do not cover or obstruct the ventilation openings on the product.
•  Do not immerse the product in water or other liquids.
• Do not expose the product to water, rain, moisture, or high humidity.
• Do not operate the product close to combustible gas or open fire.
• Do not operate appliances that may feed power back into the power inverter.
• Do not open the product, there are no user serviceable parts inside.
• Disconnect the product from the power source before cleaning.
• Disconnect the product from the power source before service and when replacing parts.
• Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
• Do not let children play with the packaging material. Always keep the packaging material out of the reach of children.
• Always keep the power cable and the product away from usual walkways.
• Do not drop the product and avoid bumping.
• Do not use aggressive chemical cleaning agents when cleaning the product.
• This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock

Mounting the power inverter

Keep at least 50cm of space to the wall from the fans on the rear of the power inverter.

1. Hold the power inverter in the desired position.
2. Mark four holes with a pencil using the power inverter as a template.
3. Drill the holes using a power drill and a drill bit.
4. Mount the power inverter on the desired position using screws.

Connecting the power inverter (Image C)

Wear protective gloves when installing the power cables.

Use tools with insulated handles when installing the power cables.

1. Connect the power cables A2 to the cable terminals on the rear of the power inverter B1B2.
2. Connect the other end of the power cables to a 12/24 V battery system.

Make sure the polarity matches the polarity of the battery.

Connecting the remote

1. Mount the remote in a desired position.
2. Plug one end of the remote cable A4 into the remote.
3. Plug the other end of the remote cable A4 into the remote port on the front of the power inverter B5.
   If the remote is used, make sure the power switch on the power inverter B8 is set to OFF.

Powering a socket device

Make sure the target device is switched off before connecting it.

1. Plug the power plug from a target device into the power socket B4.
2. Switch on the power inverter using the power switch B8 or the remote.

The power indicator LED B10 switches on.
If the remote is used, make sure the power switch on the power inverter B8 is set to OFF.

Do not load the power inverter more than 80% during long use (>1 hour).

Powering a USB device

1. Plug a USB cable into the USB port B6B7 of the power inverter.
2. Plug the other end of the USB cable into your target device.
3. Switch on the power inverter using the power switch B8 or the remote.

The power indicator LED B10 switches on.
If the remote is used, make sure the power switch on the power inverter B8 is set to OFF.

Troubleshooting

If the target device is not receiving power, look at the indicator LEDs and listen for alarms. The table below shows what the combinations of lights and sounds mean.

Disposal

The product is designated for separate collection at an appropriate collection point. Do not dispose of the product with household waste.
For more information, contact the retailer or the local authority responsible for the waste management.

Nedis BV
De Tweeling 28, 5215 MC ’s-Hertogenbosch – The Netherlands service@nedis.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>