SW-MOTECH HPR.00.220.20300-B Hand Protector Kit Instruction Manual
- June 1, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH HPR.00.220.20300-B Hand Protector Kit
Product Information
Specifications:
- Model Numbers: HPR.00.220.20300/B, HPR.00.220.80300/B, HPR.00.220.20000/B
- Colour: Black
- Material: High-Quality Plastic
- Weight: Varies by model
- Dimensions: Varies by model
Product Usage Instructions
-
Assembly:
Follow the assembly instructions provided in the user manual. Ensure all parts are securely connected. -
Installation:
Choose a suitable location for the product. Mount it securely using appropriate hardware (not included). -
Operation:
Turn on the product using the power button located on the front panel. Use the control panel to adjust settings as needed. -
Maintenance:
Regularly clean the product with a damp cloth. Avoid using harsh chemicals that may damage the surface.
Frequently Asked Questions (FAQ):
-
Q: Can I use this product outdoors?
A: It is recommended to use this product indoors to prevent exposure to extreme weather conditions. -
Q: How do I troubleshoot if the product does not turn on?
A: Check the power source and connections. Ensure the power button is functioning properly. If issues persist, contact customer support.
The application list and suitable handguard shells can be found on our website.
Important Instruction
ATTENTION:
The assembly of this product can be complicated and requires a good technical
understanding. If you are not sure of how to do this, have a specialty garage
perform the mounting and service. SW-MOTECH accepts no liability for damages
caused by improper installation.
ATTENTION:
After the installation check all operations of all handlebar controls,
specifically the throttle, front brake, kill switch and clutch, to ensure they
are operating correctly and are by the OEM specifications. Do not ride the
motorcycle if any controls are not operating correctly. Make sure the
handlebar can fully turn in either direction. Check periodically (50 km) that
all bolts are tight.
All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:
- Medium-strength liquid thread-locker [i.e., “Locktite”] should be used to secure all screws, bolts and nuts.
- Subject to change. Not responsible for typos.
Parts And Hardware
Mounting Instructions
- Preparation: Make sure the handlebar ends are free. Handlebar end weights must be removed if already mounted.
- NOTE: Installation is shown on the left side. Repeat for the right side with applicable parts.
- Loosely assemble the clamps (5] to the handlebar with swivel sections (6].
- Attach the backbones (1] & 12] with the applicable parts to the handlebar ends. Attach the inner ends of the backbones to the swivel sections. Position the backbone in the preferred position and tighten all screws in the following order: (7]. (Bl. (9] & (3].
ATTENTION: Use the specified torque setting on the first page!
KOBRA Handguard Shells
The application list for this product can be found on our website.
- ATTENTION: The assembly of this product can be complicated and requires a good technical understanding. If you are not sure of how to do this, have a specialty garage perform the mounting and service. SW-MOTECH accepts no liability for damages caused by improper installation.
- ATTENTION: After the installation check all operations of all handlebar controls, specifically the throttle, front brake, kill switch and clutch, to ensure they are operating correctly and are by the OEM specifications. Do not ride the motorcycle if any controls are not operating correctly. Make sure the handlebar can fully turn in either direction. Check periodically (50 km) that all bolts are tight.
- Subject to change. Not responsible for typos.
- NOTE: Installation is shown on the left side. Repeat for the right side with applicable parts.
- Attach the handguard shells (1] & [2] to the backbones [before mounting the backbones to the vehicle]. as shown in the drawing.
- ATTENTION: Tighten the screws carefully by hand (max. 2 Nm]. Do not overtighten the screws!
Contact Information
- SW-MOTECH GmbH & Co. KG Ernteweg 8/1 D 35282 Rauschenberg Germany.
- Tel. +49 [D] 64 25/8 16 8-00
- Fax +49 [D] 64 25/8 16 8-10
- info@sw-motech.com
- www.sw-motech.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>