Bega 22203 Recessed Wall Luminaire Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

Bega 22203 Recessed Wall Luminaire
Technical amendments reserved
Product Description
Installation
Cleaning Maintenance
Accessories
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bega 22203 Recessed Wall Luminaire

Bega-22203-Recessed-Wall-Luminaire-product

Technical amendments reserved

$Bega-22203-Recessed-Wall-Luminaire-fig- $1$$

Application
Recessed luminaire for glare-free lighting of floor spaces from a low mounting height.

Dark Sky
The light of this luminaire is directed evenly and highly efficiently onto the surface to be illuminated. No light is emitted into the upper half-space of the luminaire.

Product Description

LED recessed luminaire without power supply unit
Luminaire made of cast aluminium, aluminium and stainless steel
BEGA Unidure® coating technology
Matt safety glass
Silicone gasket
Required recessed opening 70 x 70mm
Recessed depth 90mm
Fixing is achieved by using two adjustable
wedge-shaped claws
1 cable entry
for connecting cable max. ø 10,5mm
Connecting terminals 2.5
Safety Class III
Protection class IP 65
Dust-tight and protection against water jets
Safety mark
Impact strength IK07
Protection against mechanical
impacts < 2 joule
Conformity mark
Weight: 0.25 kg
This product contains light sources of energy efficiency class(es) D

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 1.9 W
Luminaire connected wattage 2.3 W
Rated temperature ta=25 °C
Ambient temperature ta max=60 °C
When installed in heat-insulating
material ta max=50 °C
Voltage 24 V = DC 22 203K3
Module designation LED-0312/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 285 lm
Luminaire luminous flux 9 lm
Luminaire luminous efficiency 3,9 lm/W 22 203K4
Module designation LED-0312/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 295 lm
Luminaire luminous flux 10 lm
Luminaire luminous efficiency 4,3 lm/W

Please note
The luminaire must not have permanent contact with aggressive media. Aggressive media can be washed out of building materials and destroy the housing of the luminaire. In case of an unknown composition of the building materials, a material analysis is to be carried out before installation of the luminaire. Aggressive media that is outgoing from the surface might also affect the luminaire. Thus an overuse of cleaning agents in the surroundings of the luminaire must be avoided.

Please note
The luminaire can only be operated with an operating device that fulfils the requirements according to EN 61347-2-13. The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.

Installation

The electrical connection must only be made to safety transformers according to EN 61558 – see accessories. The recessed opening will be covered by the frame of the luminaire housing. Fixing of the luminaire is achieved by using two adjustable wedge-shaped claws.

Installation into solid walls
For this purpose installation housing 10 406 is available. If the installation housing cannot be used a recessed opening of 70 x 70 mm is necessary to accept the luminaire housing. Recessed depth min. 90 mm.

Installation into wall panels
A recessed opening of 70 x 70 mm is necessary to accept the luminaire housing. Recessed depth min. 90 mm. The lateral distance between the recessed luminaire and other building parts must be at least 50 mm. The claws catch the wall panel from the backside. The minimum thickness of the wall panel is 10 mm. If the wall panel has a thickness of less than 5 mm, the panel thickness must be increased from the back side.

Undo screws
Remove the front plate with glass and gasket. Disassemble the tray for electrical equipment. Do not remove the desiccant pouch from the luminaire housing. It is needed to remove residual moisture. Lead the secondary connecting cable supplied by others from the power supply unit through the cable entry into the luminaire housing.

Make an electrical connection

Connect the black conductor with the negative pole and the red conductor with the positive pole of the power supply unit.
A 24 V safety direct voltage source with a smoothed residual ripple of max. 10 % is required for the electrical connection of the luminaire – see accessories.
If other safety direct voltage sources are used, an upstream fuse (max. 6 A) must be provided by the customer.
Assemble tray for electrical equipment.
Push luminaire housing into the recessed opening.
Tighten the screws of the claw fastener.
Place glass with gasket onto the luminaire housing so that the matt surface is inside the housing.
Assemble the front plate.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Replacing the LED module
The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. The defective glass must be replaced. Close the luminaire.

Accessories

Power supply unit for LED luminaires 24 V DC
Safety transformer according to EN 61558/VDE 0570 part 2-6

70 564 Power supply unit for 5-15 W
70 465 Power supply unit for 10-25 W
70 565 Power supply unit for 20-35 W
70 566 Power supply unit for 30-50 W
70 567 Power supply unit for 40-75 W
70 169 Power supply unit for 70-150 W
230 V y 50-60 Hz
71 134 Power supply unit for 0-70 W
AC range: AC: 198-264 V y 50-60 Hz
DC range: DC: 176-275 V

The power supply units are also suitable for the operation of several LED luminaires. In this case, the maximum wattage of the power supply unit must not be exceeded.

10 406 Installation housing
For the accessories, separate instructions for use can be provided upon request.