BEGA 50504K27 Wall and ceiling light Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 50504K27 Wall and ceiling light
DIMENSION
Ceiling and wall luminaire for indoor use
Instructions for use
Application
Ceiling and wall luminaire • indoor luminaire made of hand-blown opal glass
and metal housing, for all lighting tasks. They are ideal for places where a
soft and uniform lighting distribution is required.
Product description
- Metal housing, finish colour white
- Hand-blown opal glass, satin matt, with bayonet closure 2 mounting holes Ø 5.5 mm
- Distance apart 180 mm 2 cable entries for through-wiring for mains cable up to Ø 10.5 mm max. 3 x 1.50
- Connection terminal 2.5°
- Earth conductor connection
- LED power supply unit 220-240 V ~ 50-60 Hz
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
– Safety mark
– Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) D, E
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage per DIN EN 61547. To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 8.2 W
- Luminaire connected wattage 10.3 W
- Rated temperature ta=25 °C
- Ambient temperature ta max=35 °C
50 504K27
- Colour temperature 2700 K
- Colour rendering index CRI >90
- Module luminous flux 1165 lm
- Luminaire luminous flux 760 lm
- Luminaire luminous efficiency 73,8 lm/W
50 504K3
- Colour temperature 3000 K
- Colour rendering index CRI >90
- Module luminous flux 1205 lm
- Luminaire luminous flux 787 lm
- Luminaire luminous efficiency 76,4 lm/W
50 504K4
- Colour temperature 4000 K
- Colour rendering index CRI >90
- Module luminous flux 1255 lm
- Luminaire luminous flux 820 lm
- Luminaire luminous efficiency 79,6 lm/W
Specifications
- Lamp Module connected wattage : 8.2 W
- Luminaire connected wattage : 10.3 W
- Rated temperature : 25-35°C
- Ambient temperature : max 25-35°C
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.Lead mains supply cable through the cable entry into the luminaire housing. Fix the luminaire housing with enclosed or any other suitable fixing material onto the mountingsurface. It is imperative to use the enclosed gaskets. Make earth and electrical connections to the terminal. Place glass to the luminaire housing and observe that the cam pins fit into the notches of the glass. Screw in glass by turning it clockwise. Thus, you reach a safe and vibration- resistant holding of the glass. To release the glass from the luminaire housing turn it counter-clockwise.
Cleaning Maintenance
Clean the luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire. The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools. Disconnect from main supply. Unscrew glass from luminaire housing by turning it counter clockwise. Replace the LED unit. Screw in the glass by turning it clockwise. The defective glass must be replaced.
Spares
- Spare glass 11 003 568 .0RG
- LED unit 2700 K 75 001 897 .1K 27
- LED unit 3000 K 75 001 897 .1K 3
- LED unit 4000 K 75 001 897 .1K 4
- info@bega.com
- www.bega.com
FAQ
Q: Can I replace the LED unit myself?
A: Yes, a qualified person can replace the LED unit using standard
tools. Make sure to disconnect from the main supply before starting the
replacement process.
Q: How do I remove the glass from the luminaire housing?
A: Twist the glass counterclockwise to release it from the luminaire
housing.
Q: What should I do if I encounter overvoltage issues?
A: The luminaire’s electronic components have overvoltage protection,
but for additional protection, consider separate overvoltage protection
components available on the manufacturer’s website.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>