PACIFIC ENERGY ALBERNI 2.5 Wood Heater Installation Guide

PACIFIC ENERGY ALBERNI 2.5 Wood Heater

SAFETY NOTICE

If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.

MODEL: Alberni 2.5

NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to the curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the detectors. If necessary, relocate them to reduce their sensitivity.

SAFETY NOTICE
If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.

Safety and Maintenance

1. Burn cord wood only, dry well seasoned wood. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood should not be used, as it will reduce heat output, as well as contribute significantly to creosote buildup.
2. Remove ashes frequently and only when the stove is cold. Too much ash could cause embers to roll out the door when it is opened. This may pose a fire hazard. For proper operation, maintain a 25 mm minimum ash base.
3. If the glass becomes darkened from slow burning or poor wood, it can readily be cleaned with a fireplace glass cleaner when the stove is cold. Never scrape with an object or use abrasive cleaners that might scratch the glass. The type and amount of deposit on the glass is a good indication of the flue pipe and chimney buildup. A light brown dusty deposit that is easily wiped off usually indicates good combustion and dry, well-seasoned wood, therefore relatively clean pipes and chimneys. On the other hand, a black greasy deposit that is difficult to remove is a result of wet and green wood and too slow a burning rate. This will also create heavy deposit buildup in the chimney.
4. DOOR GASKETS – The gasket used by Pacific Energy (22 mm medium-density fibreglass rope) requires only light pressure to seal. This will prolong seal life. The door seal must be maintained in good condition. Periodically inspect seals and replace them if necessary. Follow the instructions included in the door gasket kit obtainable from your nearest Pacific Energy dealer.
5. DOOR GLASS – Do not slam the loading door or otherwise impact the glass. When closing the door, make sure that no logs protrude to impact the glass. If the glass gets cracked or broken, it must be replaced before using the stove. Replacement glass can be obtained from your dealer. Use ceramic glass only. Do not substitute with any other type. GLASS SIZE – 457mm x 260mm x 5mm thick. To remove broken glass, undo the four retaining screws and remove clamps, noting the position for re-assembly. Remove all particles of glass. Be careful as they are very sharp. Install new glass complete with gasket. Replace clamps and screws.
6. Do not store wood within heater installation clearances, or the space required for fuel loading and ash removal. Keep the area around the heater clean and free of loose combustibles, furniture, newspapers, etc.
7. If the heater requires cleaning, use mild soap and water only. The use of abrasive cleaners will void the warranty.
8. Establish a routine for fuelling and firing the heater. Check daily for creosote buildup until experience shows how often you need to clean the chimney to be safe.
9. Be aware that the hotter the fire, the less creosote is deposited. Weekly cleaning may be necessary in mild weather, even though monthly cleaning is usually enough in the coldest months when burning rates are higher.
10. Instruct all members of your family on the safe operation of the heater. Ensure they have enough knowledge of the entire system if they are expected to operate it. Study the section on chimney fires and the importance of following the steps outlined “in In Case of Chimney Fire”.

WARNING: Never use chemicals or any other volatile liquid to start a fire. Do not burn garbage, or flammable fluids such as gasoline, naptha, or engine oil. We strongly recommend that smoke detectors be installed.

WARNING Only use materials supplied by manufacturer when doing mainte- nence or replacements.

CAUTION

• Tighten screws very carefully, do not over-tighten
• Do not clean glass when hot
• Do not use abrasive cleaners on glass

DANGER

• HOT GLASS WILL CAUSE BURNS.
• DO NOT TOUCH THE GLASS UNTIL COOLED.
• NEVER ALLOW CHILDREN TO TOUCH GLASS.

Maintenance Checks

Check the following parts for damage such as cracks, excessive corrosion, burned out sec-tions and excessive warping**: (See website for descriptions and more detail)

Weekly

• Firebrick – Visual, for cracking.
• Door Gasket – sagging, placement, damage.

Monthly

• Brick rail tabs and brick rails.
• Air riser tube in the back of the firebox.
• Back side of the air wash chamber.
• Baffle locking pin.
• Boost tube cover.

When Cleaning the Chimney System

• Top baffle board/blanket.
• Baffle.
• Top heat shield and mounting bolt.
• Baffle Gasket.
• Brick Rails.
• Manifold.
• Some warping of the baffle is normal (up to .65 cm).
  • Replace if the baffle has permanent warping greater than this or has cracking or breakage.
  • Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your stove with broken parts may accelerate damage to other parts and may void your warranty

Creosote

Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extreme fire. The chimney connector and chimney should be inspected periodically (at least once every two months) during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated (3 mm. or more), it should be removed to reduce the risk of a chimney fire.

1. The highest smoke densities occur when a large amount of wood is added to a bed of hot coals and the air inlet is closed. The heated wood generates smoke, but without ample air, the smoke cannot burn. Smoke-free, clean burning requires leaving the air inlet relatively wide open, especially during the first 10 to 30 minutes after each loading, when most of the smoke-generating reactions are occurring. After 30 minutes or once the wood is fully charred, the air inlet can be turned down substantially without excessive smoke generation. Wood coals create very little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is passing, the more creosote will be condensed. Wet or green wood contributes significantly to creosote formation as the excess moisture that is boiled off cools the fire, making it difficult for the tars and gases to ignite, thus creating dense smoke and poor combustion. This moisture-laden smoke cools the chimney, compounding the problem by offering the smoke the ideal place to condense.
   In summary, a certain amount of creosote is inevitable and must be lived with. Regular inspection and cleaning is the solution. The use of dry, seasoned wood and ample combustion air will help to minimize the buildup.

Chimney Fires
Excessive creosote build-up can cause a chimney fire. Creosote comes from tar and organic vapours released from a slow-burning wood fire. Flammable creosote will condense and accumulate in the lining of a relatively cool chimney. When ignited, this creosote can result in an extreme fire.

Avoiding a Chimney Fire
There are two ways to avoid chimney fires:

1. Keep your chimney clear of creosote build-up by cleaning your chimney before each burn season, and as necessary (accumulations of 3 mm or more) during the season.
2. Burn clean, well-seasoned wood only (seasoned at least one year). Avoid wet or green wood.
3. Do not burn household trash, cardboard, plastics, construction lumber, treated or beach wood (as these will corrode your fireplace and void your warranty).
4. Do not leave the air inlet wide open for extended periods.
5. Keep a fire extinguisher handy.
6. Prepare a home evacuation plan with a place outside where everyone is to meet.

If You Suspect a Chimney Fire
Signs of a chimney fire may be one or more of the following:

1. A roaring sound.
2. Vibration of the chimney.
3. Flames and sparks shooting out of the top of the chimney.

In Case of a Chimney Fire

1. Immediately close the air inlets on the stove.
2. Evacuate the home, and call the local fire department.
3. After the chimney fire has been extinguished, the chimney must be cleaned and checked for stress and cracking before starting another fire. Also, check combustibles around the chimney and roof.

Appliance Dimensions

Assembly

Crate Removal

1. Carefully remove the wood top and supports.
2. Remove the plastic cover.
3. Using a 12mm wrench, remove lag bolts that secure hold-down brackets to a bottom pallet.
4. Slide the hold-down brackets away from the stove.

Side Panel Removal/Installation

1. To remove the panels, first remove the screws that secure the panel to the rear shield. Fig. #3
2. Disengage the tabs in the front of the panel by sliding the panel forward away from the unit Fig. #4.
3. To install the panels, engage the tabs on the panel front flange into the slots in the panel mounting bracket. Fig. #4
4. Attach the panel to the rear shield. Secure with two screws. Fig. #3

Installation

Warning
Under no circumstances is this heater to be installed in a makeshift or “temporary” manner. It may be fired only after the stove is installed properly. DO NOT ATTEMPT TO CONNECT THIS HEATER TO ANY AIR DISTRIBUTION DUCT. Outside combustion air or fresh air into the room may be required in your area, consult local building codes (see Combustion Air section).

• WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED PER AS/NZS 2918 AND THE APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES
• WARNING: APPLIANCES INSTALLED UNDER THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS OF AS/NZS 4013 WHERE REQUIRED BY THE REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING ‘TESTED TO AS/NZS 4013’. ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE TESTING AUTHORITY IS CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED FOR COMPLIANCE WITH AS/NZS 4013.
• CAUTION: MIXING OF APPLIANCE OR LFUE-SYSTEM COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED IN THE FIRST INSTANCE.
• CAUTION: CRACKED OR BROKEN COMPONENTS, e.g. GLASS PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION UNSAFE.
• WARNING: ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE TESTING AUTHORITY IS CONSIDERED AS BREACHING AS/NZS 4013.
• CAUTION: THIS APPLIANCE SHOULD NOT BE OPERATED WITH A CRACKED GLASS.
• CAUTION: THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES BY THESE INSTRUCTIONS.
• CAUTION: THE USE OF SOME TYPES OF PRESEVATIVE-TREATED WOOD AS A FUEL CAN BE HAZARDOUS.

Clearances – Default Flue Kit or Insulated ROOM SEAL Flue Kit.

Clearances to the back wall when using a Default Flue Kit or an Insulated ROOM SEAL flue Kit (see Figure #5) with:

• Wildcat Default Flue off the top of the unit:
  • 150mm
• Corner Clearance:
  • 100mm

Side Clearances: 400mm to Combustibles. (see Figure #5)

Clearances – Insulated ROOM SEAL Flue Kit.
Clearances to back wall (A) when using an Insulated Room Seal Flue Kit (see Figure #5) with:

• Insulated Flue off the top of the heater
  • 175mm
• Corner Clearance:
  • 100mm

Side Clearances: 400mm to Combustibles. (see Figure #5)

Minimum Clearance to Combustibles

Figure 5. AB25 AUS CLEARANCES.

Floor Protector

The stove may be installed on a combustible floor provided ember protection made from a 9mm thick non-combustible material (Bellis Board) with a thermal conductivity value of .1m2K/W. This protection must extend as follows: 450 mm in front on the firing side and be placed centrally in the 870mm width. See Figure #6 at right.

Chimney and Connector

WARNING: INSTALL THE CHIMNEY AND ALL COMPONENTS OF THE CHIMNEY SYSTEM ACCORDING TO THE CHIMNEY MANUFACTURER’S INSTRUCTIONS.

Connect to a listed chimney complying with the requirements of AS/NZS2918/2001 and a chimney suitable for use with solid fuel that is lined and in good condition and meets local building codes. The chimney flue size should be the same as the stove outlet for optimal performance. Reducing or increasing the flue size may adversely affect stove performance. The chimney flue exit is to be a minimum of 100 cm above the roof and 60 cm above the highest projection within 300 cm. The installation must meet all local codes. Do not connect this unit to a chimney flue serving another appliance. The minimum system height is 460 cm (measured from the base of the appliance).

Installation Procedure -Residential

1. Install all components to the chimney manufacturer’s installation requirements. (Outside combustion air may be required, consult local building codes. See Combustion Air section on page 11.)
2. Installed with the crimped or male ends pointing down. This will carry any liquid creosote or condensation back into the stove.
3. If a roof or ceiling support is used in the installation, you will find the chimney manufacturer’s complete instructions packed with the roof support.
4. To start installing the smoke pipe (chimney connector), slip the crimped edge of the pipe inside the stove collar. Use holes provided in the collar to secure the pipe with three screws.
5. Install the remaining lengths of pipe, one on top of the other, to the finished height of the chimney connector and secure to each other.

Firebrick Installation
This package contains 18 full-size firebricks, as well as 6 various cut- size bricks. With the heater in the upright position, install firebricks as follows:

• Install the rear firebricks, 4 full-size, two on each side of the baffle tube.
• Then place 1 brick “B” in between the full bricks on the left as shown below.
• Next, install 4 full-size firebricks and brick “C” as shown on each side of the firebox.
• Lastly, place 5 full-size firebricks and 1 of each brick B, C and 2 of D on the bottom of the heater in the pattern shown below.

ITEM DIMENSIONS PART NUMBER

• A 230 mm x 115 mm x 32 mm 5096.99
• B 57 mm x 230 mm x 32 mm 7847.3
• C 115 mm x 115 mm x 32 mm 7847
• D 57mm x 115 mm x 32 mm 7847.1

Combustion Air
Intake or combustion air can be supplied to the stove in one of two ways. Consult your local building codes before proceeding.

1. Outside air supply – (Necessary for mobile home installation, optional for residential installation.) To draw outside air through the floor, cut or drill a 102 mm diameter hole directly below the bottom hole of the ash box enclosure. Connect the enclosure to the floor with a short 102 mm diameter pipe. This hole must get its air from a ventilated crawl space or be extended with a duct to the outdoors (see Figure #8, Page 11). The use of outside combustion air for residential installation requires the unit to be secured to the structure to prevent dislodging of the air duct.
   Note: When installed in a mobile home, this unit is not designed to be operated with the firing door open. In addition to the obvious hazard of sparks landing on combustibles, an open fire door will cause the heater to draw air from the living space and possibly cause suffocation.

2. Room air supply -There is a 102 mm opening in the ash box enclosure. The stove will draw its air from the room through this opening and into the firebox intake.
   Note: The living space around the heater must be well ventilated with good air circulation. Anything that may cause a negative pressure can cause gases or fumes to be pulled into the living area. During extremely cold weather, and especially when burning at very slow rates, the upper parts of the exposed chimney may ice up, partially blocking the flue gases. If blockage occurs, flue gases may enter the living space.

Operation

CAUTION
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.

CAUTION
Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

• WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE THE FIRE.
• WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHEN IT IS OPERATING.
• WARNING: DO NOT STORE FUEL WITHIN HEATER INSTALLATION CLEARANCES.
• WARNING: DO NOT OPERATE THIS APPLIANCE AS AN OPEN FIRE.
• WARNING: OPEN AIR CONTROL (AND DAMPER WHEN FITTED) BEFORE OPENING FIRING DOOR. Your PACIFIC ENERGY heater is designed for maximum overall efficiency at a moderate firing rate. Overfiring is hazardous and a waste of fuel. Too slow a burn contributes to creosote buildup and lowers combustion efficiency.

NOTE: Left and Right as referred to in this manual are considered your left and right when facing the front of the woodstove.

Wood Selection
This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or too green or freshly cut hardwoods. Wood should be properly air-dried (seasoned) for six months or more. Wet or undried wood will cause the fire to smoulder and produce large amounts of creosote. Wet wood also produces very little heat and tends to go out often.

DO NOT BURN

• Saltwater wood *
• Treated wood
• Wet or green wood
• Coal/charcoal
• Garbage/Plastic *
• Solvents

These materials contain chlorides which will rapidly destroy metal surfaces and void warranty. Do not burn anything but wood. Other fuels (eg. charcoal) can produce large amounts of carbon monoxide, a tasteless, odourless gas that can kill. Under no circumstances should you attempt to barbecue in this heater.

How to Test Your Wood
Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more than one side within one minute. It is damp if it turns black and lights up within three minutes. If it sizzles, hisses and black-ens without igniting in five minutes it is soaked and should not be burnt.

Lighting for the First Time

Curing of the Paint Finish
To achieve the best finish, the paint on your stove must be baked on. When burning your stove for the first 2-3 times the room must be well ventilated. Open all windows and doors. Smoke and fumes caused by the curing process may cause discomfort to some individuals.

Lighting a Fire

WARNING: Never use chemicals or any other volatile liquid to start a fire.

1. Adjust the air control to the maximum firing position (start position) and open the door.
2. Place crumpled newspaper in the centre of the heater and crisscross with several pieces of dry kindling. Add a few small pieces of dry wood on top.
3. Ignite the paper and close the door.
4. After the fire has established itself, open the door and add a few small logs. Close the door.
5. Begin normal operation after a good coal base exists and the wood has charred.

Normal Operation

1. Set the air control to the desired setting. If smoke pours down across the glass (waterfall effect) this indicates you have shut the control down too soon or you are using too low a setting. As every home’s heating needs vary (based on insulation, windows, climate, etc.) the proper setting can only be found by trial and error and should be noted for future burns.
2. To refuel, adjust the air control to high, and give the fire time to brighten. Open the door slowly, this will prevent back puffing.
3. Use wood of different shapes, diameters and lengths (up to 457mm). Load your wood and try to place the logs so that the air can flow between them. Always use dry wood.
4. Do not load fuel to a height or in such a manner that would be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred. Remember to char the wood completely on maximum setting before adjusting air control for overnight burn.

WARNING: Always keep the loading door closed when burning. This heater is not designed for open-door burning.
WARNING: No alteration or modification of the combustion air control assembly is permitted. Any tampering will void the warranty and could be very hazardous.
WARNING: Do not use grates or andirons to elevate the fuel. Burn directly on the fire bricks. Replace broken or missing bricks. Failure to do so may create a hazardous condition.

DO NOT OVERFIRE THIS HEATER:
Attempts to achieve heat output rates that exceed heater design specifications can result in permanent damage to the heater and chimney.

Restarting After Extended or Overnight Burns

1. Open the door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of the embers, and close the door.
2. Adjust air control to high (left position) and in just a few minutes, logs should begin burning.
3. After the wood has been charred, reset the air control to the desired setting.
4. To achieve maximum firing rate, set control to high (left position). Do not use this setting other than for starting or preheating fresh fuel loads.

Proper Draft

1. Draft is the force that moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures in the appliance. An uncontrollable burn or a glowing red stove part or chimney indicates excessive draft.
3. The inadequate draft may cause back puffing into the room and plugging of the chimney. Smoke leaking into the room through appliance and chimney connector joints indicates inadequate draft.

CAUTION:
Ashes are to be removed only when the heater is cold. Do not burn with the ash dump door open. Doing so will create a hazardous condition. Always leave about 25 mm of ash in the firebox when cleaning.

Ash Removal
Whenever ashes get 76 mm to 102 mm inches deep in your firebox, and when the fire has burned down and cooled, remove excess ashes. Leave an ash bed approximately (25 mm) deep on the firebox bottom to help maintain a hot charcoal bed.
Ash Chute Operation: Your Alderlea stove is equipped with an ash chute system to ease the removal of ash from the ash lip area. To use this system, first, pull out the ash pan approximately 51 mm, sweep the ash into the chute located on the right side of the ash lip, and close the ash pan again. Ash Cleanout System: The ash dump handle is located under the ash lip on the left-hand side. To operate the ash dump, pull the handle out 13 mm and turn clockwise. This will unlock the ash dump and allow it to open. Hold the handle open while pulling ashes into the opening. Avoid large embers as these still contain heat value. Release the handle and push in to lock. Ensure the ash dump door is properly engaged. Fill the cavity with the remaining ash level with the firebox floor. Pull out the ashpan and discard the ashes into a metal container. Replace the ashpan and ensure it is seated properly.

Disposal of Ashes
Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed outside on a non-combustible floor or the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in a closed container until all cinders have thoroughly cooled. Other waste should not be placed in this container.

Baffle Removal

The chimney connector pipe should be disconnected from the stove to clean and inspect. Only if this is not possible should you remove the baffle assembly. CAUTION: Ceramic blanket insulation is located on top of the baffle. Do not use a vacuum in this area. DO NOT OPERATE WITH BAFFLE ASSEMBLY OR INSULATION REMOVED.

Removal
Remove the retaining pin located at the rear top of the firebox, just below the baffle. Lift the baffle and pull forward to disconnect from the supply tube. Tilt the baffle sideways to drop down and remove from the firebox. Inspect the gasket between the baffle and supply tube. If necessary, replace with gasket SSER.1395 available from your Pacific Energy dealer. Re-install baffle assembly in reverse order. The two side pieces of insulation must be tight against the side rails.

WARNING: Sweep/Clean the chimney with the baffle installed or be sure to plug the top of the baffle tube in the back of the firebox before sweeping or cleaning. Failure to prevent ash or soot from falling into the baffle tube will cause incorrect operation and will lead to premature burn out of the tube or baffle. It is recommended to inspect the liner and connector monthly and to have the liner cleaned annually or more frequently if required. Cover the opening at the top of the baffle supply tube when cleaning the chimney liner. If debris gets into the tube

Troubleshooting

Replacement Parts – Alberni 2.5
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)

ITEM DESCRIPTION PART NO.

1. …………Porcelain Black Panel Set …………… PERP.786801
2. …………Door Catch……………………………………. NE16.7825
3. …………Ash Lip……………………………………. NE25.5037901
4. …………Gasket Guides (4 pc.)……………………. NE25.7840
5. …………Replacement Glass (c/w Tape)….. NE25.5034900
6. …………Door Gasket Kit……………………WODC.NEODGKIT
7. …………Door Casting, Black………………….. NE25.5037900
8. …………Door Handle Assembly (complete)……NERP.7817
9. ………..Wood Door Handle………………………… NE16.7817
10. ……….Side Shield Bracket, ………………….. PERP.786806
11. ………. Firebrick Set…………………………………..NE25.BRIC
12. ………. Brick Rail, Left/Right………………….NE25.RAILSET
13. ……….Replacement Baffle Kit………………..NE25.BAFKIT
14. ………Baffle Pin……………………………………SSER.125001
15. ……….Ash Dump Assembly………………………. NE25.7857
16. ………. Leg (x1 only)…………………………………. PERP.7869
17. ……….Leg Adapter………………………………. PERP.786807
18. ……….Ash Drawer……………………………….. PERP.786810
19. ……….Air Shutter Assembly……………………… NE16.7826
20. ……….Secondary Air Control Assembly……….. PERP.7838
21. ……….Upper Grill……………………………….. NE25.5037902
22. ……….Removable back brick rail…………….. NE25.78325
23. …………Heat Shield…………………………………………….NERP.7867
    • Items not shown. Optional Blower………………………………..WODC.EUBLOWB

All parts may be ordered from your nearest Pacific Energy dealer. Use www.pacificenergy.net for the location of the dealer nearest you.

Compliance Plate

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.2975 ALLENBY RD., DUNCAN, BC V9L 6V

• Model: NEO 2.5, ALBERNI 2.5
• Series: A
• Type: FREESTANDING
• Tested by : HRL TECHNOLOGY PTY LTD TRAMWAY ROAD, MORWELL, VICTORIA
• Test report no : HCMG/15/013 13/MARCH/2015

WHEN TESTED UNDER : AS/NZS 4012:2014 & AS/NZS4013:2014 MAXIMUM AVERAGE HEAT OUTPUT BURNING HARDWOOD 9.9 kW OVERALL AVERAGE EFFICIENCY BURNING HARDWOOD 82% PARTICULATE EMISSIONS FACTOR – 1.0g/kg CATALYTIC COMBUSTOR – NO

Distributed by : PIVOT STOVES AND HEATING CO 234-238 MOORABOOL STREET, GEELONG, VIC 3220 pivotstove.com.au

2015 Copyright Pacific Energy Fireplace Products LTD Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

Web site: www.pacificenergy.net 2975 Allenby Rd., Duncan, BC V9L 6V8

References

• Pacific Energy – Pacific Energy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>