Live Star UX3 Wireless Microphone System User Manual
- October 30, 2023
- Live Star
Table of Contents
Live Star UX3 Wireless Microphone System
Precautions
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE
THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
When using this electronic device, basic precautions should always be taken, including the following:
-
Read all instructions before using the product.
-
Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool etc.).
-
Use this device when you are sure thatmicrophone receiverhas a stable base and it is fixed securely.
-
This product, in combination with loudspeakers and amplifier may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult with otorhinolaryngologists.
-
The product should be located away from heat sources such as radiators, heat vents, or other devices that produce heat.
-
The product should be connected to a power supply that is described in the operating instructions or are marked on the product.
-
The power supply should be undamaged and never share an outlet or extension cord with other devices. Never leave device plugged into the outlet when it is not being used for a long period of time.
-
Care should be taken that objects do not fall into liquids and liquids would not be spilled on the device.
-
The product should be serviced by qualified service personnel if:
The power supply or the plug has been damaged.
Objects have fallen into or liquid has been spilled on the product.
The product has been exposed to rain.
The product has been dropped or the enclosure damaged. -
There are some areas with high voltage inside, to reduce the risk of electric shockdo not remove cover of the microphone receiver or power supply. The cover should be removed by the qualified personnel only.
No user serviceable parts inside.
Before you start
Introduction
Wireless microphone systems with fixed transmitter’s and receiver’s frequency.
LiveStar UX3 wireless microphone are combined with handheld transmitter. There
are four fixed frequency sets, working on 626.63 MHz, 630.4 MHz, 863.425 MHz
and 864.9 MHz
Features
- Fixed transmitter’s and receiver’s frequency
- LED backlight display
- RF, AF indicators
- Volume control
- Dynamic cardioid capsule
- Balanced XLR connector and unbalanced 6,3mm TS jack outputs
Operation
Front Panel
- Power switch
- LCD display
- Radio frequency indicator
- Audio frequency indicator
- Volume control
Rear Panel
- Antenna connector
- Main power connector
- Unbalanced audio output
- Balanced audio output
Handheld microphone
- Microphone capsule
- Low battery indicator
- Power button
- Battery cover and holder
Batteries changing
- Turn battery cover counterclockwise and remove it.
- Insert 2 units of AA type alkaline batteries. Pay attention to battery polarity.
- Replace the battery cover in its place.
Receiver operation
LCD DISPLAY
Displays the current settings
RF INDICATOR
RF indicator became active when the receiver detects a radio signal sent from
transmitter.
AF INDICATOR
This LED indicates detected audio signal.
VOLUME CONTROL
Allows to adjust audio level in receivers output.
POWER BUTTON
Press power button to turn on/off the power.
ANTENNA
Antennas for RF signal transmitting to the receiver. Covered antenna can
reduce working distance, try to keep antenna uncovered in order to guaranty
maximum working distance.
POWER CONNECTOR
Connector for DC 12 V – 16 V 0.4A power supply.
UNBALANCED AUDIO OUTPUT
Unbalanced 6,3mm Jack audio output.
BALANCED AUDIO OUTPUT
Balanced audio output, XLR connector.
BATTERY COVER
Remove battery cover in order to insert or replays batteries.
BATTERY HOLDER
Battery holder for two pieces of AA sizes alkaline batteries. Pay attention
to battery polarity, wrong polarity can damage transmitter!
Specifications
General specifications
| Technical Specifications | UX3 receiver |
|---|---|
| Carrier frequency | 626.63 MHz, 630.4 MHz, 863.425 MHz, 864.9 MHz |
| Power supply | 12-16 V DC, 0.4 A |
| Output | Balanced XLR , unbalanced 6,3 mm TS JACK |
| Receiver way | Quartz controlled fixed frequency |
| Frequency reponce | 40 Hz – 18 kHz |
| Antenna | BNC |
| T.H.D | 0,5 % |
| Image rejection | 85 dB |
| Max. audio output | -6 dBu (balanced), -12 dBu (unbalanced) |
| Dimensions (H x W x D) | 42 mm x 200 mm x 150 mm |
| Weight | 1.4 kg |
| Material | Steel and aluminum |
| Technical Specifications | UX3 handheld transmitter |
| --- | --- |
| Modulation | FM |
| Transmitter’s power | 10 mW |
Working range
| 60 m (Note: actual range depends on RF signal absorption, reflection and
interference)
Polar pattern| Cardioid
Battery| 2 x 1,5 V AA Alkaline battery
Material| Steel and aluminum
The specifications above are correct at the time of printing this manual. For improvement purposes, all specifications for this unit, including design and appearance, are subject to change without prior notice
AMC is a registered trademark of AMC Baltic www.amcpro.eu