PACIFIC ENERGY Vista LE Wood Stove Instruction Manual

PACIFIC ENERGY Vista LE Wood Stove

Product Information

Specifications

• Model(s): VISTA LE, VISTA CLASSIC LE
• Serial #: [insert serial number]
• Meets the Environmental Protection Agency’s 2020 Particulate Emission Standards (Crib Wood)

Safety Notice
If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.

Operating and Installation Instructions
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.

• Baffle/Tube Removal
  To remove the baffle and tube, follow these steps.

• Tube/Baffle Board Removal
  To remove the tube and baffle board, follow these steps.

• Installation
  To install the stove, follow these instructions.

• Dimensions
  The dimensions of the product are as follows.

• Crate Removal
  To remove the crate, follow these steps.

• Assembly – Legs (Leg Model)
  If you have a leg model, follow these steps to assemble the legs.

• Assembly – Optional Ash Cleanout
  If you have the optional ash cleanout, follow these steps to assemble it.

Important Safety Information

WARNING:
HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH THE GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS.

STATE of CALIFORNIA WARNING:
This product can expose you to chemicals including ceramic fibres, which are known to the state of California to cause cancer, and carbon monoxide, which is known to the state of California to cause birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov. This warning applies to all PACIFIC ENERGY FIREPLACE PRODUCTS.

PLEASE SAVE THESE INSTRUCTIONS

NOTE:
WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE INSTALLED IN THE AREA WHERE THE HEATER IS TO BE INSTALLED. If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to the curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the detectors.

Product Usage Instructions

Experience will give you the right settings for proper combustion and efficient burning. Remember the correct air inlet setting is affected by variables such as type of wood, outside temperature, chimney size, and weather conditions. With practice, you will become proficient in operating your heater and will obtain the performance for which it was designed.

FAQ (Frequently Asked Questions)

• Q: Can I install the stove myself?
  A: We recommend following the installation instructions provided and consulting with local building or fire officials to ensure proper installation and compliance with restrictions and inspection requirements in your area.

• Q: How can I prevent burns from the hot glass?
  A: Never touch the glass until it has cooled down. Keep children away from the glass to avoid burns.

• Q: Are there any health risks associated with this product?
  A: The state of California has issued a warning regarding potential health risks associated with ceramic fibres and carbon monoxide. Please refer to the warning statement and visit the provided website for more information.

SAFETY NOTICE
If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.

Meets the Environmental Protection Agency’s 2020 Particulate Emission Standards (Crib Wood).

Visit www.pacificenergy.net for the most recent version of this manual VISTA LE/VISTA CLASSIC LE.

WARNING

• HOT GLASS WILL CAUSE BURNS.
• DO NOT TOUCH THE GLASS UNTIL COOLED.
• NEVER ALLOW CHILDREN TO TOUCH GLASS.

STATE of CALIFORNIA

WARNING:
this product can expose you to chemicals including ceramic fibres, which are known to the state of California to cause cancer, and carbon monoxide, which is known to the state of California to cause birth defects or other reproductive harm.

PLEASE SAVE THESE INSTRUCTIONS

NOTE:
WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE INSTALLED IN THE AREA WHERE THE HEATER IS TO BE INSTALLED.

If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to the curing of stove paint or fumes caused by accidentally leaving the fire door open. Do not disconnect the detectors.

SAFETY NOTICE:
If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection require-ments in your area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death. Experience will give you the right settings for proper combustion and efficient burning. Remember the correct air inlet setting is affected by variables such as type of wood, outside temperature, chimney size and weather conditions. With practice, you will become proficient in operating your heater and will obtain the performance for which it was designed.

Rating Label

PLEASE SAVE THESE INSTRUCTIONS
This manual describes the installation and operation of the Pacific Energy, VISTA LE or VISTA CLASSIC LE Freestanding wood heater.

SAFETY NOTICE:

• If this stove is not properly installed, a house fire may result. For your safety, follow the installation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
• Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.
• This heater meets the 2020 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2020, using Method 28R.

Model VISTA LE/VISTA CLASSIC LE: 1.9 g/hr..
Under specific test conditions, this heater has been shown to deliver heat at rates ranging from 13,500 to 23,200 BTU/hr.

Efficiency and BTU Output

Fuel| Ideal Wood Length| Maximum Wood Length| EPA BTU Output 3| HHV Tested Efficiency 2| LHV Tested Efficiency 1| EPA Certified Emissions
---|---|---|---|---|---|---
Seasoned Cordwood| 16 inches| 18 inches| 13,494 to 23,186 btu/hr.| 72%| 78%| 1.9 grams per hour

1. Weighted Average Lower Heating Value (LHV) efficiency as tested using CSA B415 Performance testing of solid-fuel-burning heating appliances. LHV assumes the moisture is already in a vapour state so there is no loss of energy
2. Weighted Average Higher Heating Value (HHV) efficiency as tested using CSA B415 Performance testing of solid-fuel-burning heating appliances. HHV includes the energy required to vaporize the water in the fuel
3. The range of BTU outputs is based on efficiency using CSA B415 Performance testing of solid-fuel-burning heating appliances and burn rates from the low and high EPA tests using Douglas Fir dimensional lumber.

Safety

CAUTION:
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this heater. Keep all such liquids well away from the heater while it is in use.
Instruct all members of your family on the safe operation of the heater. Ensure they have enough knowledge of the entire system if they are expected to operate it. Stress the section on chimney fires and the importance of following the steps outlined in “In Case of Chimney Fire”.

Chimney Smoke and Creosote Formation
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote. The creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extreme fire. The chimney connector and chimney should be inspected periodically (at least once every two months) during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated (3 mm. or more), it should be removed to reduce the risk of a chimney fire.

1. The highest smoke densities and emissions occur when a large amount of wood is added to a bed of hot coals and the air inlet is closed. The heated wood generates smoke, but without ample air, the smoke cannot burn. Smoke-free, clean burning requires small fuel loads, two or three logs at a time or 1/4 to 1/2 of fuel load and leaving the air inlet relatively wide open, especially during the first 10 to 30 minutes after each loading, when most of the smoke generating reactions are occurring. After 30 minutes or so, the air inlet can be turned down substantially without excessive smoke generation. Wood coals create very little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is passing, the more creosote will be condensed. Wet or green wood contributes significantly to creosote formation as the excess moisture that is boiled off cools the fire, making it difficult for the tars and gases to ignite, thus creating dense smoke and poor combustion. This moisture-laden smoke cools the chimney, compounding the problem by offering the smoke the ideal place to condense.

In summary, a certain amount of creosote is inevitable. Regular inspection and cleaning is the solution. The use of dry, seasoned wood and ample combustion air will help to minimize annoying smoke emissions and creosote buildup.

Chimney Fires

• The dangerous side effect of excessive creosote buildup is a chimney fire. This causes much higher than normal temperatures in the chimney and on its exterior surfaces. Temperatures inside the chimney can exceed 2000°F (1100°C).
• Ignition of nearby or touching combustible material is more likely during a chimney fire. Proper clearances are critical to prevent damage during such a fire.

Chimney fires are easy to detect; they usually involve one or more of the following:

• Flames and sparks shooting out of the top of the chimney
• A roaring sound
• Vibration of the chimney

To Avoid a Chimney Fire

1. Burn wood cleanly. Do not burn wet wood or turn down the unit too quickly after loading.
2. Do not let creosote build up to a point where a chimney fire is possible.
3. Do not have fires in the heater that may ignite chimney fires. These are excessively hot fires, such as when burning household trash, cardboard, Christmas tree limbs, or even ordinary fuel wood; (e.g. with a full load on a hot bed of coals and with the air inlet wide open for more time than is needed to completely char a fresh fuel load.)
4. The Chimney and connector pipe should be inspected /cleaned periodically.

In Case of a Chimney Fire

1. Prepare to evacuate to ensure everyone’s safety. Have a well-understood plan of action for evacuation. Have a place outside where everyone is to meet.
2. Close the air inlet on the stove.
3. Call the local fire department. Have a fire extinguisher handy. Contact your local municipal or provincial fire authority for further information on how to handle a chimney fire. It is most important that you have a clearly understood plan on how to handle a chimney fire.
4. After the chimney fire is out, the chimney must be cleaned and checked for stress and cracks before starting another fire. Also, check combustibles around the chimney and the roof.

The services of a certified installer/Chimney Sweep (from one of the associations listed below), are strongly recommended to inspect and service your Chimney system

NFI (National Fireplace Institute®) in the United States, CSIA (Chimney Safety Institute of America) in the United States and Canada, WETT (Wood Energy Technology Transfer) in Canada or  APC (Association des Professionnels du Chauffage) in Quebec

Curing of the Paint Finish
To achieve the best finish, the paint on your stove must be baked on. When burning your stove for the first 2-3 times the room must be well ventilated. Open all windows and doors. Smoke and fumes caused by the curing process may cause discomfort to some individuals.

• Follow the procedures on the information sheet included with your stove from STOVE BRIGHT (Forrest Paint).

WARNING:
Never use chemicals or any other volatile liquid to start a fire. Do not burn garbage, or flammable fluids such as gasoline, naptha, or engine oil.

Operation

• CAUTION: Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.
• WARNING: Always keep the loading door closed when burning. This heater is not designed for open-door burning.
• WARNING: No alteration or modification of the combustion air control assembly is permitted. Any tampering will void the warranty and could be very hazardous.
• WARNING: Do not use grates or andirons to elevate the fuel. Burn directly on the fire bricks. Replace broken or missing bricks. Failure to do so may create a hazardous condition.

Wood Selection
This heater is designed to burn natural wood only. Higher efficiency and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or green or freshly cut hardwoods.
Wood should be properly air-dried (seasoned) for six months or more. Wet or undried wood will cause the fire to smoulder and produce large amounts of smoke and creosote. Wet wood also produces very little heat and tends to go out often. Wood should be stored under cover away from open flame or heat sources.

DO NOT BURN:

plastic
•     Construction or demolition debris| •     Materials containing asbestos
•     Waste petroleum products, paints, paint thinners, or asphalt products| • Paper products, cardboard, plywood, or particleboard.

These materials contain chlorides which will rapidly destroy metal surfaces and void warranty.

• Burning these materials may result in the release of toxic fumes or render the heater ineffective and cause smoke.
• Do not burn anything but wood. Other fuels, e.g. Charcoal, can produce large amounts of carbon monoxide, a tasteless, odourless gas that can kill. Under no circumstances should you attempt to barbecue in this heater.
• The prohibition against burning these materials does not prohibit the use of fire starters made from paper, cardboard, sawdust, wax and similar substances to start a fire in an affected wood heater.

How to Test Your Wood
Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more than one side within one minute. It is damp if it turns black and lights up within three minutes. If it sizzles, hisses and blackens without igniting in five minutes it is too wet and should not be burnt

Lighting a fire

WARNING:
Never use chemicals or any other volatile liquid to start a fire.

1. Adjust the air control to the “High” position (to the left) and open the door.
2. Place crumpled newspaper in the centre of the heater and crisscross with several pieces of dry kindling. Add a few small pieces of dry wood on top.
3. Ignite the paper and leave the door ajar approximately 1/2″(13mm) – 1″(25mm) until the wood kindling is fully engulfed in flame.
4. After the kindling is fully engulfed add a few small logs. Close door.
5. Begin normal operation after a good coal base exists and the wood has charred.

Normal Operation

WARNING:
This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with the operating instructions in this manual.

1. Set the air control to the desired setting. If smoke pours down across the glass (waterfall effect) this indicates you have shut the control down too soon or you are using too low a setting. The wide range control panel makes finding the desired setting for your application easy. As every home’s heating needs vary (i.e. Insulation, windows, climate, etc.) The proper setting can only be found by trial and error and should be noted for future burns.
2. To refuel, adjust the air control to high, and give the fire time to brighten. Open the door slowly, this will prevent back puffing.
3. Use wood of different shapes, diameters and lengths (up to 18″(457mm)). Load your wood endwise and try to place the logs so that the air can flow between them. Always use dry wood.
4. Do not load fuel to a height or in such a manner that would be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred. Remember to char the wood completely on maximum setting before adjusting air control for overnight burn.

Burn wood only, dry and well seasoned. The denser or heavier the wood when dry, the greater its heat value. This is why hardwoods are generally preferred. Green or wet wood will cause a rapid buildup of creosote. If you feel it is necessary to burn wet or unseasoned wood, do so only with the air inlet set open enough to maintain a good strong fire and fairly high chimney temperatures. Do not attempt to burn overnight using green wood or wet wood. Wet wood can cause up to 25% drop in heater output, as well as contributing significantly to creosote buildup.

DO NOT OVERFIRE THIS HEATER:
Attempts to achieve heat output rates that exceed heater design specifications can result in permanent damage to the heater and chimney. A glowing red, top or vent pipe are indication of overfiring. Failure to rectify an over-firing condition can be hazardous and may void the manufacturer’s warranty.

Restarting After Extended or Overnight Burns

1. Open the door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of the embers, and close the door.
2. Adjust air control to high and in just a few minutes, logs should begin burning.
3. After the wood has been charred, reset the air control to the desired setting.
4. To achieve maximum firing rate, set control to high “H”. Do not use this setting other than for starting or preheating fresh fuel loads.

Proper Draft

1. Draft is the force that moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures in the appliance. An uncontrollable burn or a glowing red stove part or chimney indicates excessive draft.
3. The inadequate draft may cause back puffing into the room and plugging of the chimney. Smoke leaking into the room through appliance and chimney connector joints indicates inadequate draft.

Remember the correct air inlet setting is affected by variables such as type of wood, outside temperature, chimney size and weather conditions.

Ash Removal

Caution:
Ashes are to be removed only when the heater is cold. Whenever ashes get 3″(76mm) to 4″(102mm) deep in your firebox, and when the fire has burned down and cooled, remove excess ashes. Leave an ash bed approximately 1″ (25 mm) deep on the firebox bottom to help maintain a hot charcoal bed.

Ash Cleanout system (optional on VISTA LE):
The ash dump handle is located under the ash lip on the left-hand side. To operate the ash dump, pull the handle out 1/2″(13mm) and turn clockwise. This will unlock the ash dump and allow it to open. Hold the handle open while pulling ashes into the opening. Avoid large embers as these still contain heat value. Release the handle and push into the lock. Ensure the ash dump door is properly engaged. Fill the cavity with the remaining ash level with the firebox floor. Lift and pull out the ash pan and discard the ashes into a metal container. Replace the ash pan and ensure it is seated properly.

Do not burn with the ash dump door open. Doing so will create a hazardous condition. Always leave about 1″(25mm) of ash when cleaning.

Disposal of Ashes
Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be placed on a non-combustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in a closed container until all cinders have thoroughly cooled. Other waste should not be placed in this container.

Maintenance

WARNING:
Never use chemicals or any other volatile liquid to start a fire. Do not burn garbage, or flammable fluids such as gasoline, naptha, or engine oil.

WARNING:
ONLY USE MATERIALS SUPPLIED BY THE MANUFACTURER WHEN DOING MAINTENANCE OR REPLACEMENTS.

1. If the glass becomes darkened through slow burning or poor wood, it can readily be cleaned with a fireplace glass cleaner when the stove is cold. Never scrape with an object that might scratch the glass. The type and amount of deposit on the glass is a good indication of the flue pipe and chimney buildup. A light brown dusty deposit that is easily wiped off usually indicates good combustion and dry, well-seasoned wood and therefore relatively clean pipes and chimneys. On the other hand, a black greasy deposit that is difficult to remove is a result of wet and green wood and too slow a burning rate. This heavy deposit is building up at least as quickly in the chimney.

2. DOOR GASKETS – The gasket used by Pacific Energy (3/4″(22mm) Firm Density fibreglass rope) requires only light pressure to seal. This will prolong seal life. The door seal must be maintained in good condition. Periodically inspect seals and replace them if necessary. Follow the instructions included in the DR31.WDGKIT kit, obtainable from your nearest Pacific Energy dealer.

3. DOOR GLASS – Do not slam the loading door or otherwise impact glass. When closing the door, make sure that no logs protrude to impact the glass. If the glass gets cracked or broken, it must be replaced before using the stove. Replacement glass can be obtained from your dealer. Use 10-1/2″(266mm) x 16-1/2″(419mm) x 5 mm. Ceramic glass only. Do not substitute with any other type.

   • To remove broken glass, undo the four retaining screws and remove clamps and frame, noting the position for re-assembly. Remove all particles of glass. Be careful as they are very sharp. Install new glass complete with gasket. Replace the frame, clamps and screws.
     CAUTION:

   • Do not over tighten, tighten screws very carefully

   • Do not clean glass when hot

   • Do not use abrasive cleaners on glass

4. The area where boost combustion air enters the firebox must be kept clear of excessive ash buildup which will block airflow. This area is at the front of the firebox.

5. Do not store wood within heater installation clearances, or the space required for fuel loading and ash removal. Keep the area around the heater clean and free of loose combustibles, furniture, newspapers, etc.

6. If the plated door requires cleaning, use mild soap and water only. The use of abrasive cleaners will void the warranty.

7. Establish a routine for the fuel, wood burning and firing technique. Check daily for creosote buildup until experience shows how often you need to clean to be safe.

8. Be aware that the hotter the fire, the less creosote is deposited. Weekly cleaning may be necessary in mild weather, even though monthly cleaning is usually enough in the coldest months when burning rates are higher. When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled

Maintenance Checks

Check the following parts for damage such as cracks, excessive corrosion, burned-out sections and excessive warping: (See website for descriptions and more details)

Weekly:

• Firebrick – Visual, for cracking.
• Door Gasket – sagging, placement, damage.

Monthly

• Brick rail tabs and brick rails.
• Air riser tube in the back of the firebox.
• Back side of the air wash chamber.
• Baffle locking pin.
• Boost tube cover.
• Baffle Tubes

When Cleaning the Chimney System:

• Top baffle board/blanket.
• Baffle.
• Top heat shield and mounting bolt.
• Baffle Gasket.
• Brick Rails.
• Manifold.

Blower:
The blower should be cleaned out a minimum of every six months by using a vacuum on the grill openings in the back and bottom of the blower casing to remove any dust and debris.

Baffle:

• Some warping of the baffle is normal(up to 1/4” or .65cm). Replace if the baffle has permanent warping greater than this or has cracking or breakage.
• Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your stove with broken parts can accelerate damage to other parts and may void your warranty

Baffle/Tube Removal

The chimney connector pipe should be disconnected from the stove to clean and inspect. Only if this is not possible should you remove the baffle assembly.

DO NOT OPERATE WITH BAFFLE ASSEMBLY, TUBES OR INSULATION REMOVED.

Baffle Removal

1. Slide the Ceramic Board located above the tubes towards the front of the stove. Remove the retaining pin at the back of the firebox, just under the baffle.
2. Lift the Baffle to disconnect from the Baffle supply tube.
3. Move the Baffle to one side then tilt it sideways to drop down and remove from firebox. You may need to remove the opposite side brick rail to allow the Baffle to drop down. – To remove the Brick Rail, remove the brick directly under it then lift the rail up and inward to clear the locating pins
4. Inspect the gasket between the baffle and supply tube. If necessary, replace with gasket (prt#80000365) available from your Pacific Energy dealer.
5. Re-install baffle assembly in reverse order. The two side pieces of blanket insulation must be tight against the side rails. The Ceramic Board on top of the tubes must be pushed back tight against the Baffle.

Tube/Baffle Board Removal

1. With a set of vice-grips, grasp the front baffle tube on the right, slightly away from the baffle air assembly. While squeezing tightly, use a hammer to hit the pliers and pull the tube to the right to disengage the tube from the hole on the left. Allow the tube to hang freely from the hole on the right.
2. Repeat step #1 for the rear baffle tube.
3. Grasp the front edge of the baffle board and pull forward. Guide the board down and through the door opening. Caution – Baffle Board material is very fragile.

Installation

1. With the holes facing down/forward and the notch to the left side, insert a baffle tube into the hole in the baffle air channel on the right at an angle and then raise and insert into the opposite hole on the left side baffle air assembly.
2. With a set of vice-grips, grasp the baffle tube on the left, slightly away from the baffle air assembly. While squeezing tightly, use a hammer to hit the pliers and push the tube to the left to engage the tube in the hole on the left.
3. With the rear tube installed, Insert the baffle board above the tube, between the tube and the side hold-down tabs.
4. Repeat steps #1 & #2 with the remaining baffle tube, being careful not to damage the board.
5. Slide the baffle board back until the lower edge is tight against the baffle.

Dimensions

Crate Removal

1. Carefully remove the crate top and supports.
2. Remove the plastic cover.
3. On Leg units, remove the stove from its supports by loosening the nuts holding the support to the unit

Assembly

Assembly – Legs (Leg Model)

1. With the unit on its back, Insert the leg around the first nut and between the Leg Adapter flange and the washer and second nut.
2. Using the guides cast into the tops of the leg, align the guides into the notches in the Ash Box mounting flanges.
3. Tighten the bolts down.

Assembly – Optional Ash Cleanout

Pedestal Model

1. Remove the Ash Drawer Front Cover Plate by removing the center screw(1) and lifting up to disengage the bottom tab.
2. Remove the Knock-out in the top left corner of the opening
3. Install the Ash Dump mechanism, following the instructions on the next page.
4. Install the new Ash Pan into the Pedestal.

Leg Model

1. Remove the two screws holding the Leg Ash Box front cover (located on either side). Remove the cover
2. Remove the Knock-out in the top left corner of the opening
3. Install the Ash Dump mechanism, following the instructions.
4. Install the new Ash Pan into the Leg Ash Box.

Ash Dump Installation

1. Remove the Ash Cleanout hole cover plate and gasket, located under the stove. Discard the cover plate.
2. Place the provided gasket(s) around the upper tube portion of the new Ash Dump mechanism, as per the drawing.
3. Insert The Ash Dump mechanism with gasket from underneath the firebox bottom up into the open hole and over the two bolts hanging down. – The release handle should be facing forward and on the left.
4. Re-attach the nuts onto the carriage bolts. And tighten to gently compress the gasket.

Floor Protector

The stove may be installed on a combustible floor, provided noncombustible ember protection is used. This protection must extend as follows:

In USA:
16″ (406 mm) to the front and 8″ (203 mm) to the sides of the fuel loading door opening. See Figure #4, below. This protection is also required under the chimney connector and 2″ (51 mm) beyond each side.

U.S.A. Only

• Minimum Width – 33 3/8″(850mm)
• Minimum Overall Depth – 35″(8 9 0 mm)

In Canada:
18″ (457 mm) on the firing side and 8″ (203 mm) to the other sides.

CANADA Only

• Minimum Width – 40 3/4″(1.035m)
• Minimum Overall Depth – 45″(1.14 mm)

Residential Installation

Clearances:

• Clearances may be reduced with various heat shielding/insulating materials. Consult CSA B365 or NFPA 211 and local fire codes and authorities for approval. For close clearances, use a listed double-wall connector.
• NOTE: local/national codes or regulations may override some guidelines in this manual
• We recommend that our products be installed and/or serviced by professionals who are certified by a “Qualified agency”;
• NFI (National Fireplace Institute®) in the United States,
• CSIA (Chimney Safety Institute of America) in the United States and Canada,
• WETT (Wood Energy Technology Transfer) in Canada or
• APC (Association des Professionnels du Chauffage) in Quebec

Warning:
Under no circumstances is this heater to be installed in a makeshift or “temporary” manner. It may be fired only after the following conditions have been met.

• DO NOT ATTEMPT TO CONNECT THIS HEATER TO ANY AIR DISTRIBUTION DUCT.
• Outside combustion air or fresh air into the room may be required in your area, consult local building codes (see Combustion Air section).

Chimney and Connector

• The chimney system must be a ULC-S629 or UL-130HT-listed Stainless chimney or a Masonry chimney suitable for use with solid fuel, that is lined, in good condition and meets fire and building codes.
• The chimney flue size should be the same as the stove outlet (6 inches) for optimal performance. Reducing or increasing the flue size may adversely affect stove performance.
• The chimney flue exit is to be 3 feet (1 m.) above the roof and two feet (0.6 m.) above the highest projection within 10 feet (3 m.) horizontally.
• The installation must meet all local codes.
• Do not connect this unit to a chimney flue serving another appliance. The minimum system height is 15 feet (4.6 m.) (measured from the base of the appliance).

BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO:

• IN CANADA – ULC S-641 LISTED for double wall connector and ULC-S629 LISTED CHIMNEY,
• IN THE USA – UL-103 HT LISTED CONNECTOR AND CHIMNEY

When using a Double-Wall Connector

• Use a listed double-wall connector.
• If a listed chimney and double-wall connector are to be connected to the stove, install all components as per the chimney/connector manufacturer’s installation requirements.

When using a Single-Wall (smoke pipe) Connector
The single wall pipe section must be:

• If you are using a smoke pipe/chimney connector in conjunction with the listed chimney system, consult local/national fire or building codes for connector installation. Follow the chimney manufacturer’s complete instructions for the installation of the chimney system.
• As short and straight as possible, use a six-inch diameter, 24 gauge black pipe that is clean and in new condition.
• Installed with the crimped or male ends pointing down. (This will carry any liquid creosote or condensation back into the stove) and secured at every joint and collar with 3 sheet metal screws.
• The chimney connector shall not pass through an attic, roof space, closet or similar concealed space, floor, or ceiling. Where passage through a wall, or partition of combustible material is desired, the installa-tion shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances and Equipment or NFPA 211 Standard for Chimneys, Fireplaces, Vents and Solid-Fuel Burning Appliances.

Installation Procedure

1. Select the position for your wood stove based on the clearance diagram. Position the floor protection and stove.
2. Mark the position for the hole in the ceiling and roof by using a string and plumb-bob hanging over the exact centre of the stove’s flue pipe.
3. Check that the intended location will not interfere with floor joists, ceiling joists or rafters before proceeding further. Adjust if necessary and reconfirm the clearances from the stove to the combustibles.
4. Carefully follow the directions of the listed chimney for installation of the chimney system from the ceiling through to the rain cap. This may include framing in holes etc.
5. Start installing the smoke pipe/chimney connector, and slip the crimped edge of the pipe inside the stove collar. Use holes provided in the collar to secure the pipe with two screws.
6. Install the remaining lengths of pipe one on top of the other up to the finished height of the chimney and using the manufacturer’s approved adapter, secure them to each other. A slip section can make this easier.

Combustion Air

Intake or combustion air can be supplied to the stove in one of two ways. Consult your local building code or CAN/CSA-B365, Installation Code for Solid- Fuel-Burning Appliances and Equipment before proceeding.

Outside air supply
(Necessary for mobile home installation, optional for residential installation.)

To draw outside air through the floor
This hole must get its air from a ventilated crawl space or be extended with duct to the outdoors (see Figure #3, Page 7). The use of outside combustion air for residential installation requires the unit to be secured to the structure to prevent dislodging of the air duct.

• Leg Model: Cut or drill a hole in the floor, (large enough to fit 4″ metal flex venting) behind the ash box enclosure. Once the stove is in place, attach the 4″ Intake Starter to the Ash Box Enclosure. Connect to the floor with the 4″(100mm) i.d. metal flex pipe.
• Pedestal Model: Cut or drill a 4″ (100mm) diameter hole in the floor anywhere inside the perimeter of the pedestal base. Cover the hole with a 4″ x 4″ (100 mm x 100 mm) rodent screen and staple/nail in place. Leave the cover over the hole on the back of the Pedestal. Place the stove over the hole.

To draw outside air from behind the stove, Use a 4″(100mm) Air intake. Cut or drill the recommended size hole through a wall behind the unit.

• Install the 4″ Intake Starter over the hole in the rear of the Ash Box enclosure. Attach metal flex between the starter and the Air Intake.
• Pedestal Model: Remove the cover plate from the rear of the pedestal and install the cover plate over the hole located under the Pedestal. Install the 4″ Intake Starter over the hole in the rear. Attach metal flex between the starter and the wall inlet.

Room air supply
The stove will draw its air from the room through the opening in the Ash Box Enclosure and into the firebox intake.

Note:
The living space around the heater must be well-ventilated with good air circulation. Anything that may cause a negative pressure can cause gases or fumes to be pulled into the living area. During extremely cold weather, and especially when burning at very slow rates, the upper parts of the exposed chimney may ice up, partially blocking the flue gases. If blockage occurs, flue gases may enter the living space.

Through Wall Installations
(as per NFPA 211-2013)

ATTENTION:
VAPOUR BARRIER MUST BE MAINTAINED WHEREVER THE CHIMNEY OR OTHER COMPONENTS PENETRATE THE EXTERIOR OF THE STRUCTURE. SEE LOCAL BUILDING CODES FOR PROPER AND APPROVED METHODS OF MAINTAINING VAPOUR BARRIER.

Minimum Clearance 12 in. (305mm) to combustibles
System A. Minimum 3.5 in. (90 mm) thick brick masonry wall framed into the combustible wall with a minimum of 12 in. (305 mm) brick separation from clay liner to combustibles. Fireclay liner (ASTM C 315, Standard Specifications for Clay Fire Linings, or equivalent), minimum 5/8 in. (16 mm) wall thickness, shall run from the outer surface of a brick wall to, but not beyond, the inner surface of the chimney flue liner and shall be firmly cemented in place.

Minimum Clearance 9 in. (229mm) to combustibles

• System B. Solid-Insulated listed factory-built chimney length of the same inside diameter as the chimney connector and having 1 in. (25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air space between the outer wall of the chimney length and combustibles.
• The inner end of the chimney length shall be flush with the inside of the masonry chimney flue and shall be sealed to the flue and to the brick masonry penetration with non-water-soluble refractory cement. Supports shall be securely fastened to wall surfaces on all sides.
• Fasteners between supports and the chimney length shall not penetrate the chimney liner.

Minimum Clearance: 6 in. (152mm) to combustibles

• System C. Sheet steel chimney connector, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24 gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4 mm) air channels, separated from combustibles by a minimum of 6 in. (152 mm) of glass fibre insulation. The opening shall be covered, and the thimble supported with a sheet steel support, minimum 24 gauge [0.024 in. (0.61 mm))] in thickness.
• Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold the chimney section. Fasteners used to secure the chimney section shall not penetrate the chimney flue liner.

Minimum Clearance: 2 in. (51mm) to combustibles

• System D. Solid-insulated listed factory-built chimney length with an inside diameter 2 in. (51 mm) larger than the chimney connector and having 1 in. (25.4mm) or more of insulation, serving as a pass-through for a single-wall sheet steel chimney connector of minimum 24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in. (51 mm) air space between the outer wall of chimney section and combustibles.
• The minimum length of the chimney section shall be 12 in. (305 mm). The chimney section is concentric and spaced 1 in. (25.4 mm) away from the connector employing sheet steel support plates on both ends of the chimney section. The opening shall be covered, and the chimney section supported on both sides with sheet steel supports of mini-mum 24 gauge [0.024 in. (0.61 mm)] thickness.
• Supports shall be securely fastened to wall surfaces on all sides and shall be sized to fit and hold the chimney section. Fasteners used to secure the chimney section shall not penetrate the chimney flue liner.

Mobile Home Installation

Warning:
Under no circumstances is this heater to be installed in a makeshift or “temporary” manner. It may be fired only after the following conditions have been met.

• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
• DO NOT INSTALL IN A SLEEPING ROOM.
• CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.
• Attach the stove to the floor using two 1/4″ x 2″ or longer lag screws through holes in the legs or the Pedestal base.
• Outside air supply must be used for Mobile Home installations.
• The services of a competent or certified installer, (certified by the Wood Energy Technical Training program (WETT) – in Canada, and Hearth Education Foundation (HEARTH) – in the U.S.A.,) are strongly recommended.

Clearances

• This heater must be installed with the listed double-wall connector and compatible ULC-S629 or UL-103HT listed chimney system, see page 18.
• Clearances to combustible surfaces and materials are shown. See picture below.
• Consult local fire codes and authorities for approval.

NOTE:
Install all components to the connector or chimney manufacturer’s installation requirements. Consult your chimney supplier/manufacturer for installation advice.

Use Only
Double Wall Flue Connector for Mobile Home

Optional Blower

The optional blower kit Part #: WODC.BLOWB is equipped with a three-prong power cord and may be installed at any time. Follow the installation instructions supplied with the kit. Route the power supply cord away from the heater.

• Electrical rating: 115 volts AC-1.02 amps.
• Fan output rating: 140 CFM

Blower Operation
Proper blower speed matched with the air control setting will ensure peak performance from your stove. Operate as follows:

• Air control set to “L” (low), operate blower speed control on “Low”.
• Air control set between “L” and “H” (low and high), operate blower speed control at the desired setting.

Automatic:
To operate the blower automatically, set the rocker switch on the side of the fan housing to “Auto” and set the speed control to your desired setting. This will allow the fan to turn on as the stove heats up to operating temperature. It will also shut the blower off after the fire has gone out and the unit has cooled to below a useful heat output range.

Manual:
To manually operate the blower, set the rocker switch to “Man” and set the speed control to your desired setting. This will bypass the temperature- sensing device and allow full control of the blower. Switching from “Auto” to “Man” or selecting speed may be done anytime.

Note: The Blower will not shut off until it is manually turned off.

Firebrick Installation

Begin firebrick installation with the rear wall.

1. Stand one “A” firebrick vertically behind the tab located on the brick rail. Slide the firebrick toward the centre of the rear wall (Figure 18).

2. Slide a 2nd “A” firebrick underneath the tab on the brick rail (Figure 19).

3. Repeat steps 1 & 2 for the placement of the other “A” firebricks on the rear wall (Figure 20).

4. For the side walls: Stand an “A” firebrick against the side wall and up against the rear wall firebrick (Figure 21).

5. Stand another “A” brick beside the first one followed by a narrow “B” firebrick (Figure 22).

6. Place a “D” firebrick on top of the previously placed “A” firebricks and slide this firebrick back toward the rear wall making sure that this firebrick tucks in behind the brick rail (Figure 23).

7. Slide an “E” firebrick under the side wall brick rail tab and rest on top of the three previously placed side wall firebricks (Figure 24). Repeat steps 4-7 on the other side (Figure 25).

8. Units with Ash Dump installed:

   • Place two “A” firebricks on the firebox floor as shown in (Figure 26).
   • Place a third “A” firebrick against the rear wall as shown in (Figure 27).
   • Place the “C” firebrick so that it sits beside the ash dump, against the lefthand side wall and the “A” firebrick located directly behind the ash dump (Figure 28).

9. Units without Ash Dump installed:
   Place 4 “A” firebricks on the firebox floor as shown in. Push the brick to the back of the firebox.

10. Place the two remaining “B” firebricks in front of the other floor firebricks to complete the firebrick installation (Figure 28 and Figure 29).

Note: there will be one brick left over.

Troubleshooting

Low Heat Output

|

1. Wood may be wet

|

– Check wood and use drier wood if required.

 | 2) Fire too small| – Build a larger fire
 |  | – Open draft control to increase burn rate.
 | 3) Draft too low| – Is the chimney plugged or restricted Inspect and clean
Won’t Burn Overnight| 1)  Air control set too high

2)  Not enough wood

3)  Draft too high

| –   Set control lower

–   Unsplit wood is preferred for overnight burns

–   Excessive chimney height and/or diameter, see page 11

---|---|---
Stove Won’t Burn| 1) Combustion air supply is blocked| –   Check outside air supply for obstructions

–   Check that room air cover is removed.

 |  | – Is the chimney plugged or restricted Inspect and clean

Replacement Parts

VISTA CLASSIC LE

CLASSIC ONLY ENAMEL PARTS:

• 1…… Top, Ebony Black……………………………………………………………………..80002397
• …….. Top, Ivory………………………………………………………………………………..80002398
• …….. Top, Sunset Red………………………………………………………………………80002399
• 2…… Side, Ebony Black……………………………………………………………………80002400
• …….. Side, Ivory……………………………………………………………………………….80002401
• …….. Side, Sunset Red……………………………………………………………………..80002402
• 3…… Ash Shelf, Ebony Black…………………………………………………………….80001000
• …….. Ash Shelf, Ivory………………………………………………………………………..80000342
• …….. Ash Shelf, Sunset Red………………………………………………………………80001005
• 4…… Casting, Trivet, Met Black………………………………………………………….11260005
• …….. Casting, Trivet, Nickel……………………………………………………………….11260006
• 1……. Side shield, left or right………………………………………………………………………..80002386
• 2……. Door catch, Vista LE……………………………………………………………………………80002387
• 3……. Ashlip (c/w hardware)………………………………………………………………………….80000018
• 4……. Air Control, Primary ……………………………………………………………………………80002215
• 5……. Ash dump assembly……………………………………………………………………………80001793
• 6……. Ash drawer enclosure………………………………………………………………………….80002388
• 7……. Ash box (leg model)…………………………………………………………………………….80002389
• 8……. Ash Drawer Enclosure Cover………………………………………………………………..80002390
• 9……. Pedestal…………………………………………………………………………………………….80002391
• 10….. Ash box (pedestal model)…………………………………………………………………….80002392
• 11….. Pedestal front cover assembly……………………………………………………………..80002393
• 12….. Firebrick, NEO 1.6 LE / Vista LE (set)…………………………………………………….80002355
• 13….. Glass(c/w Tape), NEO 1.6…………………………………………………………………….80000220
• 14….. Glass Retainer, NEO 1.6 / Vista LE………………………………………………………..80002356
• 15….. Gasket, Door, NEO 1.6/ Vista LE…………………………………………………………..80000670
• 16….. Casting, Door, Vista LE, Black………………………………………………………………80002394
• ……… Casting, Door, Vista LE, Nickel……………………………………………………………..80002395
• ……… Casting, Door, Vista LE, Brushed Nickel………………………………………………..80002396
• 17….. Door handle assembly…………………………………………………………………………80000660
• 18….. Door Assembly, Met Black…………………………………………………………………..11190026
• ……… Door Assembly, Nickel…………………………………………………………………………11190025
• ……… Door Assembly, Brushed Nickel……………………………………………………………11190024
• 19….. Tube Air Box Gasket, NEO 1.6 LE / Vista LE…………………………………………..80002359
• 20….. Tube Air Box (RHS), NEO 1.6 LE / Vista LE…………………………………………….80002365
• 21….. Tube Air Box (LHS), NEO 1.6 LE / Vista LE…………………………………………….80002358
• 22….. Tubes, NEO 1.6 LE /Vista LE (set of 2)…………………………………………………..80002364
• 23….. Baffle Board, NEO 1.6LE / Vista LE……………………………………………………….80002357
• 24….. Flame Shield, NEO 1.6 LE / Vista LE,…………………………………………………….80002360
• 25….. Baffle, Pin, (10pc)………………………………………………………………………………..80000364
• 26….. Baffle, NEO 1.6 LE / Vista LE………………………………………………………………..80002361
• 27….. Brick Rail Set, Left/Right, NEO 1.6 LE / Vista LE…………………………………….80002363
• 28….. Baffle Blanket (set), NEO 1.6 LE / Vista LE……………………………………………..80002362
• 29….. Rear Brick Rail, NEO 1.6……………………………………………………………………..80001723
• 30….. Casting, Leg, Black…………………………………………………………………………….80000148
• ……… Casting, Leg, Nickel…………………………………………………………………………….80000783
• ……… Casting, Leg, Brushed Nickel……………………………………………………………….80000147
• 31….. Legs, (4pc kit), Black…………………………………………………………………………..11130006
• ……… Legs, (4pc kit), Nickel………………………………………………………………………….11130007
• ……… Legs, (4pc kit), Brushed Nickel……………………………………………………………..11130004

All parts may be ordered from your nearest Pacific Energy dealer. Contact Pacific Energy for the location of the dealer nearest you.

© 2018 Copyright Pacific Energy Fireplace Products LTD. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws.

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.

• 2975 Allenby Rd., Duncan, B.C. V9L 6V8
• Web site: http://www.pacificenergy.net

For additional technical support, please contact your dealer

Printed in Canada.

References

• p65warnings.ca.gov
• Pacific Energy – Pacific Energy

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>