BEGA 33052 Shielded Recessed Luminaire Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 33052 Shielded Recessed Luminaire Instruction Manual
Dimension
Instructions for use
Application
Shielded recessed luminary for walls. The color temperature of the luminary can be set optionally to 3000K and 4000K.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Tricoat® coating technology
Colour graphite or silver Matt safety glass Fixing is achieved by using two
adjustable wedge-shaped claws
Required recessed opening 505 x 110mm
Recessed depth 90mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5mm
Connecting terminal and earth conductor terminal 2.5@
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminary
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK08
Protection against mechanical
impacts < 5 joule
r – Safety mark
c – Conformity mark
Weight : 3.2 kg
This product contains light sources of energy efficiency class(es) C
Safety
The installation and operation of this luminary are subject to national safety
regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminary, the person responsible
for these modifications shall be considered the manufacturer.
Over voltage protection
The electronic components installed in the luminary are protected against over
voltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate over voltage protection components. You can find them on our website
at www.bega.com.
The ideal protection of all electronic components installed in the illuminates is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.
Please note:
This luminary is coated with BEGA Tricolor. BEGA Tricolor is a registered trademark for a technology that we use to achieve optimal corrosion resistance.
Even the best possible surface protection and the highest corrosion resistance can be rendered almost ineffective in some cases by aggressive media caused by leaching of building materials.
Where such media are suspected, a material analysis must be carried out before
installation.
Always avoid excessive use of chemical cleaning agents in the vicinity of the
luminaire.
Installation
The recessed opening will be covered by the frame of the luminary housing. Fixing of the luminary is achieved by using two adjustable wedge-shaped claws.
Installation in solid, plastered walls:
The installation housing 10 438 is available for this purpose. If this is not
used, an exact recessed opening of 505 x 110mm with a minimum depth of 90mm is
required.
Installation in exposed brickwork:
The construction of an on-site recessed opening with the exact installation
dimensions of 505 x 110mm with a minimum depth of 90mm is required. An
installation housing cannot be used.
Installation in dry walling:
A recessed opening of 505 x 110mm with a minimum depth of 90mm is required.
The claws grip behind drywall.
Installation into insulated facades:
For installation in EWIS external wall insulation systems please use
installation housing 13 524 in combination with a plaster frame 10 038
or 13 508.
Open luminaire:
Undo hexagon socket screws (SW 4) and remove housing cover.
Disconnect plug-connection of the LED connecting cable.
Disconnect the earth conductor connection from the plug connection.
Lead the mains supply cable through the cable entry into the luminaire
housing.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminary
The LED module can optionally be operated with a colour temperature of 3000 K
or 4000 K.
Check the labelling to ensure a correct socket match when connecting the plug-
in device to the LED connecting cable.
Switching may only be carried out when disconnected from the power supply!
Put on earth conductor connection of the housing cover. Assemble housing
cover.
Make sure that gasket is positioned correctly.
Tighten the screws evenly.
Insert luminary housing into the recessed opening. Hand-tighten screws of the
claw fastener (torx drive T25) evenly. Do not use an electric screwdriver!
Lamp
Module connected wattage : 9.6 W
Luminaire connected wattage: 10.9 W
Module designation: LED-1538/83040
Colour rendering index : CRI >80
Rated temperature: ta=25 °C
Ambient temperature: ta max=55 °C
When installed in heat-insulating material: ta max =50 °C
Operation at colour temperature : 3000 K
Module luminous flux : 1845 lm
Luminaire luminous flux : 132 lm
Luminaire luminous efficiency: 12,1 lm/W
Operation at colour temperature: 4000 K
Module luminous flux : 1870 lm
Luminaire luminous flux : 134 lm
Luminaire luminous efficiency: 12,3 lm/W
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Accessories
10 438: Installation housing
13 524: Installation housing for installation in insulated façades (EWIS)
10 038 : Plaster frame
13 508 : Plaster frame flush
A separate instructions for use can be provided upon request
Spares
LED power supply unit : DEV-0451/350
LED module : LED-1538/83040
Gasket: 83 001 619
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>