Bega 50 035 Ceiling and Wall Luminaire For Indoor Use Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
50 035 Ceiling and Wall
Luminaire For Indoor Use
Instruction Manual Technical amendments reserved
50 035
Ceiling and wall luminaire for indoor use
50 035 Ceiling and Wall Luminaire For Indoor Use
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required.
Product description
Metal housing, finish colour white Hand-blown opal glass, satin matt, with
bayonet closure 2 mounting holes ø 5.5 mm
Distance apart 230 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x
1.5@ 3-pole plug connection with connecting terminal and earth conductor
terminal 2.5@
2-pole connection for digital control LED power supply unit 220-240 V x
0/50-60 Hz
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components Safety
class I
Impact strength IK05
Protection against mechanical impacts < 0.7 joule
– Safety mark
****– Conformity mark
Weight: 3.2 kg
This product contains light sources of energy efficiency class(es) D, E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 16.4 W |
|---|---|
| Luminaire connected wattage | 19.6 W |
| Rated temperature | ta= 25 °C |
| Ambient temperature | ta max a= 30 °C |
50 035 K27
| Colour temperature | 2700 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2335 lm |
| Luminaire luminous flux | 1423 lm |
| Luminaire luminous efficiency | 72,6 lm / W |
50 035 K3
| Colour temperature | 3000 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2415 lm |
| Luminaire luminous flux | 1473 lm |
| Luminaire luminous efficiency | 75,2 lm / W |
50 035 K4
| Colour temperature | 4000 K |
|---|---|
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2510 lm |
| Luminaire luminous flux | 1531 lm |
| Luminaire luminous efficiency | 78,1 lm / W |
Luminaire with trim ring:
Before installing onto the mounting surface the luminaire housing must be
inserted into the trim ring (accessory).
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on
to the mounting surface.
It is imperative to use the enclosed gaskets.
Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
Place glass to the luminaire housing and observe that the cam pins fit into
the notches of the glass.
Screw in glass by turning it clockwise. Thus, you reach a safe and vibration-
resistant holding of the glass.
To release the glass from the luminaire housing turn it counter-clockwise.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to
those of the LED units originally fitted. The LED unit can be replaced by
qualified persons using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Replace the LED unit.
Screw in glass by turning it clockwise.
Defective glass must be replaced.
Accessory · Trim rings
For this luminaire metal trim rings in 3 enamel surfaces are optional
available.
Trim rings are accessories and must be ordered separately.
| Part. No
---|---
Colour white| 13 004
Colour palladium| 13 005
Colour glossy silver| 13 006
Spares
| Spare glass | 11 003 180 .0R G |
|---|---|
| LED unit 2700 K | 75 001 904 .1K 27 |
| LED unit 3000 K | 75 001 904 .1K 3 |
| LED unit 4000 K | 75 001 904 .1K 4 |
BEGA Gantenbrink-Leuchten KG
· Postfach 31 60
· 58689 Menden
· info@bega.com
· www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>