BEGA 512776 System Pendant Luminaire Indoor Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 512776 System Pendant Luminaire Indoor
Product Information
Specifications
- Lamp Module connected wattage: 15.2 W
- Luminaire connected wattage: 18 W
- Colour temperature: 3000 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 2095 lm
- Luminaire luminous flux: 854 lm
- Luminaire luminous efficiency: 47.4 lm / W
Product Usage Instructions
Safety
The installation and operation of this luminaire must comply with national
safety regulations. Only a qualified electrician should perform installation
and commissioning. The manufacturer is not liable for damages due to improper
use or installation.
Overvoltage Protection
The luminaire’s electronic components have overvoltage protection according to
DIN EN 61547. For additional protection,consider separate overvoltage
protection components available on the manufacturer’s website.
Installation
Handle LED components carefully during installation. Avoid direct contact with
the light output opening. Follow these steps for installation:
- Guide the reflector into the housing cover.
- Hang the reflector onto the struts by turning clockwise.
- Attach the housing shield to the pendant unit by turning it clockwise.
LED Module Replacement
Before replacing the LED module, remove the end cover from the pendant unit
without tools. Follow these steps for LED module replacement:
- Disconnect the system and open the luminaire.
- Replace the module with a qualified person using appropriate tools.
- Follow the installation instructions for the LED module and close the luminaire.
Additional Component Requirement
To operate this luminaire, an additional BEGA Installation component must be
ordered. Refer to the instructions for the specific component selected for
luminaire installation. The manufacturer is not liable for damages if the
recommended BEGA installation component is not used.
FAQ (Frequently Asked Questions)
Q: Can the luminaire be operated without a qualified electrician?
A: No, only a qualified electrician should perform installation and
operation to ensure safety and proper functioning of the luminaire.
Q: How can I ensure overvoltage protection for the luminaire?
A: The luminaire’s electronic components have built-in overvoltage
protection. For additional protection, consider using separate overvoltage
protection components available on the manufacturer’s website.
Q: What should I do before replacing the LED module?
A: Before replacing the LED module, disconnect the system, open the
luminaire, and follow the specific installation instructions for replacing the
module provided in the user manual.
System pendant luminaire for indoor use
Instructions for use
Application
Pendant luminaire · Indoor luminaire with aluminium housing for glare-free,
downwarddirected light.
Some of the light is emitted upwards and softly highlights the exterior finish
of the upper luminaire body.
BEGA System pendant luminaire for use in combination with various modular BEGA
installation components.
Product description
Pendant luminaire »STUDIO LINE«
Luminaire housing made of aluminium,surface colour velvet white inside hue
matt copper
Light-diffusing silicone lens
Synthetic reflector, colour white
Cable pendant · Sheath cable white 2 x 0,75@
Overall length of luminaire approx. 2000 mm
Safety class III
– Conformity mark
Weight: 0.7 kg
This product contains light sources of energy efficiency class(es) E Luminaire
without canopy,for connection to an additional required BEGA Installation
component (accessory)
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 15.2 W
- Luminaire connected wattage 18 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 40 °C
51 277.6 K3
- Module designation LED-0910/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 2095 lm
- Luminaire luminous flux 854 lm
- Luminaire luminous efficiency 47,4 lm / W
Please note:
The luminaire can only be operated with an operating device that fulfills the
requirements according to EN 61347-2-13.
The maximum idle voltage of 60 V DC must conform to SELV or SELV equivalent.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Guide the supplied reflector with the profile recess facing forwards into the
housing cover and hang onto the three struts by turning clockwise.
Pass the enclosed housing shield with its inner ring to the front in central
position over the pendant unit.
Insert the housing shield into the profile recess and fasten it to the pendant
unit by turning it clockwise.
To operate this luminaire one of the following additional BEGA Installation
components must be ordered – accessoire.
Please refer to the instructions for use for the BEGA installation component
selected for luminaire installation
Please note:
The manufacturer accepts no liability for damage caused by improper use or
installation if no BEGA installation component is used to install this BEGA
system pendant luminaire.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Please note before replacing the LED module:
The end cover on the top can be removed from the pendant unit without tools.
First push the luminaire cable back approximately 20 mm through the cable
entry into the pendant unit, then remove the end cover from the pendant unit
by pulling lightly on the luminaire cable.
Squeeze the light-diffusing silicone lens with two fingers and remove it from
the pendant unit.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by a
qualified person using commercially available tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Close the luminaire.
Accessories
BEGA Installation components with LED power supply unit.
Satin white finish.
Depending on the desired type of installation,the following suitable installation components are available for this BEGA system pendant luminaire:
For all level ceilings:
-
13 238 Surface-mounted canopy (Type A)
DALI · 220-240 V · 490 mA DC -
13 266 Surface-mounted canopy (Type AS)
Smart controllable/dimmable ·
220-240 V · 490 mA DC
Suitable for level ceilings and sloped ceilings with a pitch of 0 – 40°:
-
13 244 Surface-mounted canopy (Type B)
DALI · 220-240 V · 490 mA DC -
13 250 Recessed canopy (Type C)
DALI · 220-240 V · 500 mA DC -
13 272 Recessed canopy (Type CS)
Smart controllable/dimmable · -
220-240 V · 500 mA DC
For flush and surface-mounted 3-phase
Eurostandard-Plus® track systems:
- 13 218 Track adapter (Type D)
DALI · 220-240 V · 500 mA DC
Spares
- Silicone lens 15 000 485
- LED module 3000 K LED-0910/930
- Housing shield 71 003 533 B4
- Reflector 76 002 109 DB1
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>