QualGear QG-PRO-PM-50-B Projector Mounting Bracket Instruction Manual

June 2, 2024
QualGear

QualGear QG-PRO-PM-50-B Projector Mounting Bracket

QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket-PRO

Product Information

Specifications:

  • Product: Projector Mounting Bracket
  • Compatibility: For 1.5-inch NPT Threaded Pipes
  • Model: QG-PRO-PM-50-B
  • Warranty: 1-Year Limited Warranty (Version: Sep 2023)

Product Usage Instructions

Installation Precautions:

  • Read the entire installation manual before starting installation and assembly.
  • Ensure good mechanical aptitude and experience with basic building construction.
  • Follow instructions carefully to prevent damage or injury.
  • Check the supporting surface’s load-bearing capacity.
  • Use an assistant or lifting equipment for safe equipment positioning.
  • Avoid over-tightening screws to prevent damage.
  • Indoor use only; outdoor use voids warranty.
  • Secure mounting screws into the centre of wooden studs with an edge-to-edge stud finder.
  • Avoid exceeding the maximum weight limit specified in the manual.
  • Use designated points for bolts and screws to prevent property damage and injury.
  • Avoid installing near air conditioner vents, excessive dust, or smoke.
  • Avoid electrical cables, water, or gas pipes when drilling holes in the ceiling.

Parts Checklist:

  • Projector Bracket (x1)
  • M6 x 8mm Screw (x1)
  • 4mm Allen Key (x1)
  • Hardware Package:
    • M3 x 8mm Screws (x4)
    • M4 x 10mm Screws (x4)
    • M5 x 10mm Screws (x4)
    • M6 x 10mm Screws (x4)
    • M4 x 25mm Screws (x4)
    • M6 x 25mm Screws (x4)
    • D3-D6 Washers (each x4)
    • 5mm Spacers (x8)

Installation Steps:

  1. Disassemble the Projector Bracket
  2. Connect the Adapter Bracket to the Extension Column
  3. Attach the Adapter Bracket to the Projector
  4. Connect the Projector Assembly to the Extension Column
  5. Maintenance – Detach the Projector Assembly from the Extension Column
    • Remove the Projector Mounting Screws
    • Detach the Projector Bracket from the Projector

Frequently Asked Questions (FAQ)

  • Q: Can this product be used outdoors?
    A: No, all QualGear products are intended for indoor use only. Using them outdoors will void the limited warranty.

  • Q: What should I do if any parts are missing or damaged?
    A: Please contact support@qualgear.com for replacement parts before starting assembly and installation.

  • Q: How do I ensure proper weight distribution when mounting the projector?
    A: Make sure to follow the specified weight limits in the manual and use all provided hardware at designated points to ensure proper weight distribution and prevent damage or injury.

SAFETY WARNINGS

NOTE Please read the entire installation manual before you start installation and assembly.

WARNING

  • Only begin installing your QualGear product once you have read and understood all the instructions and warnings in this installation manual. If you have any questions regarding the instructions, please contact QualGear customer support via email at support@qualgear.com.
  • This product should only be installed by someone of good mechanical aptitude who has experience with basic building construction and fully understands these instructions.
  • This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.
  • Ensure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Always use an assistant or mechanical lifting equipment to lift and position the equipment safely.
  • Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.
  • All QualGear products are intended for indoor use only, and any outdoor use voids the limited warranty.
  • If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.
  • Never exceed the maximum rated weight specified in this manual.
  • All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and personal injury.
  • Do not install near air conditioner vents or where there is excessive dust or smoke.
  • When drilling holes in the ceiling, it is very important to take care of electrical cables, water, or gas pipes in the ceiling.

Parts Checklist

IMPORTANT: Before starting installation, please ensure all parts in this checklist are included. If any parts are missing or damaged, please contact support@qualgear.com for replacement parts, and do not start assembly and installation until you receive all the parts.

QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket-
\(2\)

Hardware Package

QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket-
\(3\)

INSTALLATION INSTRUCTION

  1. Disassemble the Projector Bracket.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(4\)
  2. Connect the Adapter Bracket to the Extension Column.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(5\)
  3. Attach the Adapter Bracket to the Projector.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(6\)
  4. Connect the Projector Assembly to the Extension Column.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(7\)
  5. A. Adjustments – Pitch.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(8\)
    • B. Adjustments – Roll.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(9\)
    • C. Adjustments – Swivel.
  6. A. Maintenance – Detach the Projector Assembly from the Extension Column.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(11\)
    • B. Remove the Projector Mounting Screws.
    • C. Detach the Projector Bracket from the Projector.QualGear-QG-PRO-PM-50-B-Projector-Mounting-Bracket- \(12\)

Maintenance

Please check that the projector assembly is secure and safe to use regularly. If you have questions about the instructions, please contact QualGear technical support at support@qualgear.com.

Scan the QR Code ™ below for more info about this product:QualGear-QG-PRO-
PM-50-B-Projector-Mounting-Bracket- \(1\)

CAUTION!
Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

QualGear User Manuals

Related Manuals