QualGear LP29-46T Heavy Duty Tilting TV Wall Mount Installation Guide
- June 15, 2024
- QualGear
Table of Contents
- LP29-46T Heavy Duty Tilting TV Wall Mount
- Specifications
- Product Usage Instructions
- Installing the Safety Bar and the Padlock
- Safety Bar Adjustment
- TV Angle Adjustment
- FAQ
- Q: What is the maximum weight capacity of this TV wall
- Q: Can I use this wall mount for outdoor installations?
- Q: Can I use this wall mount for commercial purposes?
- Q: Where can I find warranty information for this product?
- Q: How should I mount this wall mount to wooden studs?
- Q: What precautions should I take when drilling holes in the
- Q: What types of wall construction is this product designed
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LP29-46T Heavy Duty Tilting TV Wall Mount
Specifications
-
Product Model: QG-TM-031-BLK
-
Product Name: Heavy Duty Tilting TV Wall Mount
-
Compatible TV Size: Most 37 to 70 Flat Panel and Curved
TVs -
Maximum Weight Capacity: 40kg (88lbs)
-
VESA Mounting Patterns: 300×300, 400×200, 400×400, 600×400
-
Version: March 2016
Product Usage Instructions
Installing the Safety Bar and the Padlock
1. Make sure the TV is safely secured before proceeding.
2. The padlock is not included, so you need to acquire one
separately.
3. Fold the edge of the safety bar inward.
Safety Bar Adjustment
1. Insert the safety bar onto the rail at the bottom of the wall
plate to secure it.
2. Put a padlock on the safety bar to prevent the TV from being
stolen.
TV Angle Adjustment
To adjust the viewing angle of the TV:
1. Push or pull from the top or bottom of the screen to obtain
the desired angle.
FAQ
Q: What is the maximum weight capacity of this TV wall
mount?
A: The maximum weight capacity is 40kg (88lbs). Do not exceed
this weight limit to avoid serious injury or property damage.
Q: Can I use this wall mount for outdoor installations?
A: No, all QualGear products are intended for indoor use only.
Using them outdoors voids the limited warranty.
Q: Can I use this wall mount for commercial purposes?
A: No, this wall mount is designed and tested for residential
use only. Using it for commercial purposes voids the limited
warranty.
Q: Where can I find warranty information for this product?
A: For warranty information, please visit
http://www.qualgear.com/warranty.php.
Q: How should I mount this wall mount to wooden studs?
A: When mounting to wooden studs, make sure that the mounting
screws are anchored into the center of the studs. It is highly
recommended to use an edge-to-edge stud finder for accurate
placement.
Q: What precautions should I take when drilling holes in the
wall?
A: When drilling holes in the wall, be cautious of electrical
cables, water pipes, or gas pipes that may be present. Take
necessary measures to avoid damaging them.
Q: What types of wall construction is this product designed
for?
A: This product is designed to be installed on wooden studs,
wooden beams, solid concrete walls, or other suitable wall
constructions. Please consult a qualified professional if you are
unsure about the compatibility with your specific wall
construction.
5 Installing the Safety Bar and the Padlock
IMPORTANT: Make sure the TV is safely secured before releasing
Padlock is not included
The folded edge faces inward.
B Safety Bar
6 Adjustment
Insert the safety bar onto the rail (at the bottom of the wall plate) to secure. Put a padlock on the safety bar to prevent the TV from being stolen.
Tilt -10°~+5°
Push or pull from the top or bottom of the
screen to obtain the desired angle.
QG-TM-031-BLK
HEAVY DUTY TILTING TV WALL MOUNT
70
For Most 37″ to 70″ Flat Panel and
Curved TVs
40kg (8(48880llkbbgss) )
Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.
300×300 400×200 400×400 600×400
Version March 2016
NOTE Please read the entire installation manual before you start installation and assembly.
WARNING
Do not begin to install your QualGear product until you have read and
understood all the instructions and warnings contained in this installation
manual. If you have any questions regarding the instructions, for US customers
please contact QualGear customer support via email at support@qualgear.com.
For all international customers, please contact your local distributor.
This product should only be installed by someone of good mechanical aptitude,
has experience with basic building construction, and fully understands these
instructions.
This product was designed to be installed and utilized only as specified in
this manual. Improper installation of this product may cause damage or serious
injury. QualGear is not liable for the improper use or installation of its
products.
Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
ALL QUALGEAR products are intended for indoor use only and any outdoor use
voids the limited warranty.
ALL QUALGEAR products are designed and tested for residential use only and any
commercial use voids the limited warranty. For warranty information, please
visit http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that mounting screws are anchored into
the center of the studs. Use of an edge-to-edge stud finder is highly
recommended.
Never exceed the maximum rated weight specified in this manual.
Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.
Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
DO NOT install near air conditioner vents or where there is excessive dust or
smoke.
When drilling holes in the wall, it is very important to take care of
electrical cables, water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:
WALL CONSTRUCTION Wooden Stud Wooden Beam Solid Concrete Other
HARDWARE REQUIRED Included Included Included Contact Qualified Professional
1
Parts Checklist
IMPORTANT: Before starting installation, please check that all parts shown in
this checklist are included. If any parts are missing or damaged, contact your
local distributor or support@qualgear.com for replacement parts and do not
start assembly and installation until you receive all the parts.
Wall Plate (x1) A
Safety Bar (x1) B
ST2.9×6.5 Screw (x4) G
Hardware Package
Left Adapter Bracket (x1) C
Right Adapter Bracket (x1) D
Bubble Level (x1) E
Decorative Cover (x2) F
QG-TM-031-BLK
Marking Template (x1) H
M4x14mm (x4) M-A
M5x14mm (x4) M-B
M6x14mm (x4) M-C
M8x20mm (x4) M-D
M6x30mm (x4) M-E
M8x30mm (x4) M-F
5.5mm/8.5mm Washer (x4)
M-G
5mm Small Spacer (x8)
M-H
15mm Large Spacer (x4)
M-I
ST6.3x65mm Lag Bolt (x6)
W-A
10x60mm Concrete Anchor (x6)
W-B
D6 Washer (x6) W-C
2
1 Installing the Decorative Covers
NOTE
When decorative covers are installed correctly, there will be a gap between the bottom of the wall plate and the decorative covers. This gap is for the safety bar installation on Step 5.
F Decorative Cover
G ST2.9×6.5 Screw
Attach the decorative covers to the wall plate using the screws.
2a Mounting to a Wooden Stud Wall
Stud Finder
For concrete wall NOTE mounting, follow
Step 2b.
1 Using an edge-to-edge stud finder, find the edges of the stud.
3
2 Using a level, mark the centerline of the stud.
65mm (2.5″)
ø 4.5mm (ø 3/16″)
H
QG-TM-031-BLK
3
Using the marking template (H) provided, mark four holes for drilling on the
centerline of the stud.
A Wall Plate
4
Using a power drill and 3/16″ drill bit, drill pilot holes of 3/16″ (4.5 mm)
diameter and at least 2.5″ (65 mm) depth.
E Bubble Level
Insert the bubble level (E) on the wall plate (A)
W-C W-A
5 Mount the wall plate (A) and tighten it with the provided lag bolts (W-A)
and D6 washers (W-C) using a socket wrench.
NOTE Do NOT use power drill and do NOT over tighten the lag bolts.
WARNING
Make sure that mounting screws are anchored into the center of the studs. The
use of a stud finder is highly recommended.
Installers are responsible to provide hardware for other types of mounting
situations. Installers must verify that the supporting surface will safely
support the combined
weight of the equipment and all attached hardware and components.
SKIP TO STEP 3
4
2b Mounting to a Concrete Wall
H Marking Template
NOTE Do NOT use power drill and do NOT over tighten the lag bolts.
E Bubble Level
Insert the bubble level (E) on the wall plate (A)
QG-TM-031-BLK
1
Hold the marking template (H) provided against the wall where you want to
install the TV, mark six holes for drilling.
70mm (2.7″)
ø 10mm (ø 3/8″)
2
Using a power drill and a 3/8″ masonry drill bit, drill mounting holes of 3/8″
(10 mm) diameter and 2.7″ (70 mm) depth at the marked locations in the
previous step.
5
A Wall Plate
W-B W-C W-A
3 Place concrete anchors (W-B) in each hole. Tap each anchor flush with the
wall using a hammer. Using a socket wrench, mount the wall plate (A) and
fasten them with the provided lag bolts (W-A) and D6 washers (W-C).
WARNING
Installers must verify that the supporting surface will safely support the
combined weight of the equipment and all attached hardware and components.
6
3a Installing to a Flat Back Panel of a TV
Choose the appropriate screws and washers according to the type of your TV,
and attach adapter brackets (C and D) to the back of the TV using a Phillips
screwdriver.
D Right Adapter Bracket
C Left Adapter Bracket
Top Backside of the TV
IMPORTANT! Tighten all screws but do NOT over tighten
7
M-A/ M-B M-G
5.5mm
Flat Back Panel
OR
M-C/ M-D
M-G
8.5mm
Top of the TV
NOTE
According to the direction indicator arrows on the adapter brackets, make sure the adapter brackets are installed in the correct direction.
8
3b Installing to a Curved or Recessed Back Panel of a TV
D Right Adapter Bracket
C Left Adapter Bracket
Top Backside of the TV
IMPORTANT! Tighten all screws but do NOT over tighten
Curved Back Panel
Recessed
Back Panel
OR
NOTE
According to the direction indicator arrows on the adapter brackets, make sure the adapter brackets are installed in the correct direction.
Top Backside of the TV
Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your TV and attach adapter brackets (C and D) to the back of the TV using a Phillips screwdriver.
8.5mm
M-D M-G
M-D/ M-E/ M-F M-G
M-H
OR
M-E/ M-F M-G
M-I
4 Hooking the TV onto the Wall Plate
M-H M-H
M-E/ M-F M-G
M-H M-I
With an assistant, hook the TV onto the mounted wall plate.
9
10
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>