Visteon HARLEYIFCU Infotainment Control Unit User Manual
- June 14, 2024
- Visteon
Table of Contents
- Generalities
- Product Overview
- System Interaction
- Mounting Diagram
- Conditions and methods of Storage and Transportation
- Equipment Repair Requirements
- Disposal methods
- Instructions to Access Electronic Label
- BT Configuration
- WiFi Configuration
- Compliance Marking
- Customer Information
- Documents / Resources
Visteon HARLEYIFCU Infotainment Control Unit
Generalities
Customer: Harley Davidson Motor Co., Inc.
Model Name: HARLEYIFCU
Product Name: INFOTAINMENT CONTROL UNIT
Brand Name: VISTEON
Manufacturer: VISTEON CORPORATION
Manufacturer Address: ONE VILLAGE CENTER DRIVE. VAN BUREN TOWNSHIP 48111
MI USA.
Country of Origin: Mexico
Product Overview
Motorcycle cockpit domain controller, called Infotainment Front Control Unit (IFCU) of 12.3 inch
System Interaction
Mounting Diagram
Conditions and methods of Storage and Transportation
The storage temperature range shall be -40 to 105 degrees C.
Equipment Repair Requirements
No Hardware repairs are permitted, Instrument clusters will be out of warranty if opened.
The fuse to be used with this product must be 10A.
Recommended Fuse – 10A fuse 72462-00 (LITTLEFUSE PN 297010)
Disposal methods
In case of permanent malfunction, IFCU needs to be replaced by service center. IFCU would directly go to scrap yard.
Instructions to Access Electronic Label
-
To Revie the conformity marking on the product, you must click on settings.
-
Go to General Settings menu
-
Select option System Info
-
Select “E-Labels”
-
E-Labels will be displayed, scroll down
BT Configuration
Phone BT configuration
-
Click on Menu/Settings
-
Click on Device Manager menu, with the BT logo
-
Assure the BT is ON and Click on “Add new”
-
Wait for a couple of minutes until you device has been identified and select it.
-
Corroborate the code on the IFCU and on your phone and click “accept” on both devices
-
Corroboration of connection will appear
-
Corroboration on role of the device connected will be requested.
-
You device will now appear on the phones list
BT Headset Configuration
-
Click on Menu/Settings
-
Click on Device Manager menu, with the BT logo
-
Assure the BT is ON and Click on “Add new”
-
Wait for a couple of minutes until you headset has been identified and select it.
-
Click “OK” after that
-
Assign a Role to your headsets
-
The headsets will be added on you headsets list
WiFi Configuration
Countries with ONLY 2.4 GHz Band
*** Access point configuration will not be allowed
Station Mode
-
Click on Menu/Settings
-
Click on “WiFi” settings
-
Look for the WiFi network you want to connect and select it, you will only see 2.4GHz networks and enter the password
-
Connection will be done and the WiFi logo will change on the bottom right.
Countries with 2.4 GHz and 5GHzBand or 5GHz ONLY
**** In countries with 2.4GHz and 5GHz, connection will be allowed ONLY for 5GHz
Station Mode
-
Click on Menu/Settings
-
Click on “WiFi” settings
-
Look for the WiFi network you want to connect and select it, you will only see 5 GHz networks and enter the password
-
Connection will be done and the WiFi logo will change on the bottom right.
Access Point
-
Click on Menu/Settings
-
Click on “WiFi” settings
-
Click on “Access point”
-
Look on the device you want to connect the network that appears on the display and enter the password, you will biconnected after that.
Compliance Marking
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- The device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF exposure safety
This device complies with the FCC RF exposure limits and has been evaluated in compliance with mobile exposure conditions.
The equipment must be installed and operated and was evaluated with minimum distance of 40cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED
This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- The device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF exposure safety
This device complies with ISED RF exposure limits and has been evaluated in compliance with mobile exposure conditions. The equipment must be installed and operated and was evaluated with minimum distance of 40cm of the human body. This distance or greater is maintained by vehicle design and ensures compliance by normal use of the vehicle.
Customer Information
Declaration of Conformity
CE MARK:
Simplified EU DoC:
Hereby, Visteon Corporation declares that the Infotainment Control Unit type HARLEYIFCU is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.visteondocs.com/
Hereby, Visteon Corporation, declares that this HARLEYIFCU is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Argentina
User manual in official language
This equipment is not entitled to protection against harmful interference and may not cause interference to duly authorized systems For more information, see the ANATEL website – www.anatel.gov.br
México
Homologation by IFTXXXXXXXXX-XXXX
Certification By: NYCE
Australia and New Zealand
This device contains SRRC type approval radio transmitter module with code as: CMIIT ID: XXXXYZNNNN’.
India
User Manual in English
Japan
User manual must be in Japanese
South Korea
(It means that, as this radio equipment has the possibility of radio interference, this equipment cannot be used for any services related to human life safety)
- KC logo along with the following information (Conformity assessment information -인증 정보)):
- Company name of Applicant (인증 받은 자의 상호): Visteon Corporation
- Manufacturing date (제조연월일): 별도표기
- Manufacturer/ Country of origin (제조자/제조국가): USA
- Equipment name/ Model name (기자재의 명칭/ 모델명): HARLEYIFCU
- Conformity assessment number (인증번호): R-R-VC1-HARLEYIFCU
Malaysia
Highly recommended to provide the user manual in official language
Vietnam
Israel
User manual in Hebrew
Any safety instructions or warning on the product and/or in the documentation
should be in Hebrew as mandatory requirement. English could be enough.
“Wireless approval signed by the Ministry of Communication no. 55-14363”
Jordan
Kuwait
Highly recommended to provide the user’s manual in the national official language/languages
Qatar
No specific requirement
Russia
Saudi Arabia
South Africa
United Arab Emirates
United Kingdom
Simplified UKCA DoC:
Hereby, Visteon Corporation declares that the radio equipment type HARLEYIFCU is in compliance with the relevant statutory requirement. The full text of the Declaration of Conformity is available at the following internet address: www.visteondocs.com
a. Frequency band:
Bluetooth: 2402-2480MHz
WiFi: 2412-2472MHz / 5180-5825 GHz
b. Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates.
Max output power:
Bluetooth: 4.0 dBm
WiFi: 21.0 dBm
E-Mark
Oman
Documents / Resources
|
Visteon HARLEYIFCU Infotainment Control
Unit
[pdf] User Manual
NT8-HARLEYIFCU, NT8HARLEYIFCU, HARLEYIFCU, HARLEYIFCU Infotainment Control
Unit, Infotainment Control Unit, Control Unit, Unit
---|---