QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount Installation Guide

June 16, 2024
QualGear

QualGear logo

QG-TM-A-012
INSTALLATION MANUAL
ULTRA LOW PROFILE ARTICULATING TV WALL MOUNT

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall
Mount

■ 1 Year Limited Warranty
■ Version September 2018

QG-TM-A-012 Ultra Low Profile Articulating Wall Mount

For Most 23″ to 55″ Flat Screen TVs and Monitors

CAUTION!
Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.

ESA
75×75 | 100×100 | 200×100 | 200×200 300×300 | 400×200 | 400×400

Scan the QR Code™ below for more info about this product:

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Qr Code
1

https://www.qualgear.com/p
roducts/tv/24/qg-tm-a-012

NOTE
Please read the entire installation manual. Check to ensure that all parts are included before you start installation and assembly.

WARNING

  • Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual.
    US customers with questions regarding instructions, please contact QualGear customer support via email at support@qualgear.com
    For all international customers, please contact your local distributor.

  • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

  • This product was designed to be installed and utilized only as specified in this manual.
    Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.

  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.

  • Tighten screws firmly, but do not over tighten.
    Over tightening can damage the items, greatly reducing their holding power.

  • All QualGear products are intended for indoor use only and any outdoor use voids the limited warranty.
    All QualGear products are designed and tested for residential use only and any commercial use voids the limited warranty.
    For warranty information, please visit http://www.qualgear.com/warranty.php.

  • If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.

  • Never exceed the maximum rated weight specified in this manual.

  • All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.

  • DO NOT install near air conditioner vents or where there is excessive dust or smoke.

  • When drilling holes in the wall, it is very important to take care of electrical cables, water, or gas pipes in the wall.

  • This product was designed to be installed on the following wall construction only:
    WALL CONSTRUCTION
    Wooden Stud
    Wooden Beam
    Solid Concrete
    Other| HARDWARE REQUIRED
    Included
    Included
    Included
    Contact Qualified Professional
    ---|---

Parts Checklist

IMPORTANT: Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and  installation until you receive all the parts.

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Parts
Checklist

Hardware Package

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Hardware
Package

Separating the Center Decorative Cover from the Wall Mount

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Cover from
the Wall Mount

Removing the VESA Plate

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Removing
the VESA Plate

3a Mounting to a Wooden Stud Wall

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - For
concrete

NOTE
For concrete wall mounting, follow Step 3b.

  1. Using an edge-to-edge stud finder, find the edges of the stud.
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - For
concrete 2

  2. Using a level, mark the centerline of the stud.
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount -
centerline

  3. Using the marking template (H) provided, mark three holes for drilling on the centerline of the stud.
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Using the
marking templateUsing a power drill and 3/16″ drill bit, drill pilot holes of 3/16″ (4.5 mm) diameter and at least 2.5″ (65 mm) depth
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - power
drill

  4. Mount the wall mount (A) and tighten with the provided lag bolts (W-A) and D6 washers (W-C) using a socket wrench.
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Mount the
wall mount NOTE
    Do NOT use power drill and do
    NOT over tighten the lag bolts.

WARNING

  • Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
  • Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Installers are responsible for providing hardware for other types of mounting situations.

3b Mounting to a Concrete or Brick Wall

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount -
template

Hold the marking template (H) provided against the wall where you want to install the TV, mark four holes for drilling.

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Using a
power drill

Using a power drill and a 3/8″ masonry drill bit, drill mounting holes of 3/8″ (10 mm) diameter and 2.7″ (70 mm) depth at the marked locations in the previous step.

NOTE Do NOT use power drill and do NOT over tighten the lag bolts.

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - lag
bolts

Place concrete anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer.
Using a socket wrench, mount the wall mount (A) and fasten them with the provided lag bolts (W-A) and D6 washers (W-C).

WARNING

  • Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Installing the Decorative Covers

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Installing
the Decorative Covers

Attaching the VESA Extension Arms

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - VESA
Extension Arms

Adjust the extension arms (C&D) for VESA 400×200.

Mounting TV onto the Wall Mount

Flat Back Panel

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Flat Back
Panel

IMPORTANT! Tighten all screws but do NOT over tighten

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - icon
6

Curved Back Panel

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Curved Back
Panel

Choose appropriate screws, washers, and spacers (if necessary) according to the type of your TV, attach the VESA plate with extension arms to the back of the TV, then tighten screws using a Phillips screwdriver.

Hanging the TV onto the Wall Mount

  1. Lift your TV and guide the screws into the mounting holes on the mount.
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - the Wall
Mount

  2. Place lower nut and tighten all three nuts using a wrench (G).
    QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Place
lower

IMPORTANT!
Tighten all screws but do NOT over tighten

NOTE
Hold TV securely until all screws are firmly installed before releasing the TV.

Cable Management

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Cable
Management

Connect cables to your TV and route through the cable holders and along the arms.

Adjustments

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount -
Adjustments

Loosen screws with Allen Key (F) and make adjustments.

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Adjustments
2

Display can be adjusted to a desired viewing position by tilt and swivel the bracket

Maintenance

Please check that the wall mount is secure and safe to use at regular intervals If you have any questions regarding any of the instructions or warnings; please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.

Scan the QR Code” below to contact us:

QualGear QG-TM-A-012 Ultra Low Profile Articulating Wall Mount - Qr Code
2

https://www.qualgear.com/contact-us

| +1(972) 423-8960
---|---
| facebook.com/qualgear
| twitter.com/qualgear
| pinterest.com/qualgearusa
| support@qualgear.com
| youtube.com/qualgear
| store.qualgear.com
| google.com/+qualgear

QualGear logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

QualGear User Manuals

Related Manuals