QualGear PRB-717-WHT Universal Ceiling Mount Projector Access Instruction Manual

: May 15, 2024
: QualGear

Table of Contents

QualGear PRB-717-WHT Universal Ceiling Mount Projector Access
Product Information
Product Usage Instructions
Parts Checklist
Hardware Package
Installing the Ceiling Mount (Wood Joist Surfaces)
Attaching the Projector Bracket to the Projector
Pitch Adjustment
Maintenance
Documents / Resources

QualGear PRB-717-WHT Universal Ceiling Mount Projector Access

QualGear-PRB-717-WHT-Universal-Ceiling-Mount-Projector-Access-
PRODUCT

Product Information

Specifications

Model: PRB-717-WHT
Weight: 13.6kg (30lbs)
Warranty: 2 Year Limited Warranty
Version: December 2023

Product Usage Instructions

Installation Precautions

Read the entire installation manual before starting.
Check all parts are included before installation.
Understand all instructions and warnings.
Only install if you have good mechanical aptitude.
Do not exceed the maximum weight limit specified.
Avoid installing near-air conditioner vents or dusty areas.
Be cautious of electrical cables, water, or gas pipes when drilling holes.

Installation Recommendations

Tighten screws firmly, but do not over-tighten.
Mount to wooden studs by anchoring screws in the center.
Use an assistant or lifting equipment for safe positioning.
Use all bolts and screws at designated points only.
Ensure the supporting surface can hold the load securely.

Prohibited Usage

Avoid outdoor use as it voids the warranty.
Avoid commercial use as it voids the warranty.

Wall Construction

This product is designed to be installed on the following types of wall construction: Wooden Stud, Wooden Beam, and Solid Concrete.
For other types, contact a qualified professional.

Frequently Asked Questions (FAQ)

Q: What should I do if any parts are missing or damaged?

A: Contact your local distributor or email support@qualgear.com for replacement parts before starting assembly and installation.

Q: Can I exceed the maximum weight limit specified?

A: No, never exceed the maximum weight limit as it may cause damage or injury.

NOTE Please read the entire installation manual. Check to ensure that all parts are included before you start installation and assembly.

WARNING

Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual.
US customers with questions regarding instructions, please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.
This product should only be installed by someone of good mechanical aptitude, who has experience with basic building construction, and who fully understands these instructions.
This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.
Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.
All QualGear products are intended for indoor use only and any outdoor use voids the limited warranty.
All QualGear products are designed and tested for residential use only and any commercial use voids the limited warranty. For warranty information, please visit http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.
Never exceed the maximum rated weight specified in this manual.
All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.
DO NOT install near air conditioner vents or where there is excessive dust or smoke.
When drilling holes in the wall, it is very important to take care of electrical cables, water, or gas pipes in the wall.
This product was designed to be installed on the following wall construction only:

WALL CONSTRUCTION Wooden Stud

Wooden Beam
Solid Concrete
Other

HARDWARE REQUIRED Included

Included
Included
Contact Qualified Professional

Parts Checklist

IMPORTANT: Before starting installation, please check that all parts shown in this checklist are included.
If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts, and do not start assembly and installation until you receive all the parts.

Hardware Package

QualGear-PRB-717-WHT-Universal-Ceiling-Mount-Projector-Access-
FIG-2

Tools Needed for Assembly

Stud finder (edge-to-edge stud finder is recommended) Marking pen
5/32″ (4mm) bit for wood studs Electric drill
5/16″ (8mm) bit for solid concrete surfaces Philips screwdriver
Socket wrench Measuring tape
Hammer Level

Installing the Ceiling Mount (Wood Joist Surfaces)

For installation to concrete surfaces, skip to Step 1B. QualGear-PRB-717-WHT-
Universal-Ceiling-Mount-Projector-Access-FIG-4

Using an edge-to-edge stud finder, find the edges of the stud in the ceiling.
Using a level, mark the centerline of the stud.
Using the marking template provided, mark holes for drilling on the centerline of the stud.
Using an electric drill and a 5/32″ (4mm) drill bit, drill pilot holes to a minimum depth of 2.5″ (64mm).
Depending on the direction of the studs, choose the mounting holes accordingly.
Attach the ceiling mount with two screws (H) as shown in the figure on the left.
Using a socket wrench tighten each screw until the ceiling mount is firmly attached.
IMPORTANT: Do not use electric/power drill and do not over-tighten the screws.

WARNING

Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Make sure that mounting screws are anchored into the center of the stud. The use of an edge-to-edge stud finder is highly recommended.
Hardware provided is for attachment of mount through standard thickness drywall into wood studs, or mount to solid concrete wall. Installers are responsible for providing hardware for other types of mounting situations.
Tighten screws so that the ceiling mount is firmly attached, but do not over-tighten. Over-tightening can damage the screws, greatly reducing their holding power.

Installing the Ceiling Mount (Concrete Surfaces)

For installation to wood surfaces, refer to Step 1A.
Hold the marking template provided against the ceiling where you want to install your projector and mark four holes for drilling using a marking pen or pencil.
Using an electric drill and a 5/16″ (8mm) drill bit, drill the four mounting holes to a minimum depth of 2.5″ (64mm).

WARNING

Concrete must have a 2000 psi density minimum. Lighter-density concrete may not hold concrete anchors.
Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.
Attach ceiling mount with four concrete anchors (G) and four screws (H) as shown in the figure on the left.
Using a socket wrench tighten each screw until the ceiling mount is firmly attached.
Do not use electric / power drill and do not over-tighten the screws.

Attaching the Projector Bracket to the Projector

WARNING

If your projector model has three mounting holes only, please remove the fourth extension bracket using the supplied Allen Key (E).
If your projector model does not have at least three mounting holes, do not use this mount.
Loosen the M6x12mm Screws using the supplied Allen Key (E) until you can slide the extension brackets freely, as shown.
To suit the mounting hole configuration of your projector, you may need to replace the attached Extension Brackets with the additional short or long Extension Brackets (A, B, C, D) supplied in the package.
Place the Projector Bracket Assembly over the Projector and align the center of the Mount with the Center of Gravity of the Projector.
Align the shift adjustment opening (at the center of the projector bracket) in parallel with the projector lens opening to allow shift adjustments to the projector.
Place the Bottom Spacers (R) in between the Extension Brackets and the Projector, and align the mounting holes as shown below. If you are using a short extension bracket you must use spacer Q.
Select the correct Mounting Screws from the Hardware Package (J, K, L, M, or N) and firmly screw the Projector Bracket Assembly onto your Projector using a Philips Screwdriver.
Once this is done, the Projector Bracket Assembly is ready to be mounted onto the Ceiling Mount.
If your mounting holes are recessed into the projector, you may need to use the additional Spacers (S, T, U) supplied in the Hardware Package.
Please select the appropriate Spacer(s) according to the design of your projector.

Attaching the Projector Assembly to the Ceiling Mount

Using an assistant to support the weight of the projector, attach the Projector Assembly to the Ceiling Mount as shown above.
Tighten the M6x30mm screws on either side with the supplied Allen Key (E).
When the projector requires servicing, remove the projector via this easy disconnection point to save time.

Adjusting the Projector

Pitch Adjustment

To make a Pitch adjustment, first ensure the weight of the projector is supported.
Then loosen both M6x25mm screws with the supplied Allen Key (E), and adjust to your desired position. Re-tighten both screws firmly.

Tilt Adjustment

To make a Tilt adjustment, first ensure the weight of the projector is supported.
Then loosen both M6x20mm screws on either side with the supplied Allen Key (E) and
Wrench (F), and adjust to your desired position.
Re-tighten all screws firmly.

Roll Adjustment

To make a Roll adjustment, first ensure that the weight of the projector is supported.
Then loosen both M6x70mm bolts with the supplied Allen Key (E) and Wrench (F), and adjust to your desired position. Re-tighten both screws firmly.

Rotation/Shift Adjustment

To make Rotation / Shift adjustment(s), first ensure that the weight of the projector is supported.
Then loosen the center M6x16mm screw slightly with the supplied Wrench (F), and adjust to your desired position. Re-tighten the screw firmly.

Maintenance

Please check that the TV wall mount is secure and safe to use at regular intervals.
If you have any questions regarding any of the instructions or warnings, please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.
+1 (972) 423-8960
support@qualgear.com
facebook.com/qualgear
youtube.com/qualgear
store.qualgear.com
google.com/+qualgear
pinterest.com/qualgearusa
twitter.com/qualgear

Documents / Resources

| QualGear PRB-717-WHT Universal Ceiling Mount Projector Access [pdf] Instruction Manual
PRB-717-WHT Universal Ceiling Mount Projector Access, PRB-717-WHT, Universal Ceiling Mount Projector Access, Ceiling Mount Projector Access, Mount Projector Access, Projector Access
---|---