QualGear QG-PM-002-WHT Projector Ceiling Mount Installation Guide

June 16, 2024
QualGear

QualGear logo

QG-PM-002-WHT
INSTALLATION MANUAL
PROJECTOR CEILING MOUNT

QualGear QG-PM-002-WHT Projector Ceiling Mount

QG-PM-002-WHT Projector Ceiling Mount

Scan the QR Code below for more info this product:

QualGear QG-PM-002-WHT Projector Ceiling Mount - Qr
Code

20kg
(44Ibs)
RATED
CAUTION!
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.

1 Year Limited Warranty
Version November

NOTE Please read the entire installation manual before you start installation and assembly.

WARNING

  • Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual. If you have any questions regarding the instructions, for US customers please contact QualGear  customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.

  • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

  • This product was designed to be installed and utilized only as specified in this manual.
    Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.

  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.

  • Tighten screws firmly, but do not over tighten.
    Over tightening can damage the items, greatly reducing their holding power.

  • ALL QUALGEAR products are intended for indoor use only and any outdoor use voids the limited warranty.

  • ALL QUALGEAR products are designed and tested for residential use only and any commercial use voids the limited warranty.
    For warranty information, please visit http://www.qualgear.com/warranty.php.

  • If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.

  • Never exceed the maximum rated weight specified in this manual.

  • All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.

  • DO NOT install near air conditioner vents or where there is excessive dust or smoke.

  • When drilling holes in the ceiling, it is very important to take care of electrical cables, water, or gas pipes in the ceiling.

  • This product was designed to be installed on the following ceiling construction only:
    CEILING CONSTRUCTION
    Wooden Stud
    Wooden Beam
    Solid Concrete
    Brick
    Other| HARDWARE REQUIRED
    Included
    Included
    Included
    Included
    Contact Qualified Professional
    ---|---

Parts Checklist

IMPORTANT: Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and  installation until you receive all the parts.

QualGear QG-PM-002-WHT Projector Ceiling Mount - Parts
Checklist

Hardware Package

QualGear QG-PM-002-WHT Projector Ceiling Mount - Hardware
Package

Cable Management

QualGear QG-PM-002-WHT Projector Ceiling Mount - Cable
Management

QualGear QG-PM-002-WHT Projector Ceiling Mount - Cable Management
2

Installing the Projector Ceiling Mount Assembly

Attach the adjustable extension column to the ceiling plate with four M6 screws (M-B) and four D6 washers (M-L) using a 5mm Allen key (M-N) as shown below.

QualGear QG-PM-002-WHT Projector Ceiling Mount - Installing the
Projector

Insert the pivot bracket into the end of the inner extension column and secure with four M5 screws (M-A) and four D5 washers (M-J) using a 4mm Allen key (M-M) as shown below.

QualGear QG-PM-002-WHT Projector Ceiling Mount - Insert the pivot
bracket

3a Mounting to a Wooden Ceiling

QualGear QG-PM-002-WHT Projector Ceiling Mount - Mounting to a Wooden
Ceiling

WARNING

  • Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  • Installers are responsible for providing hardware for other types of mounting situations.

3b Mounting to a Brick or a Concrete Ceiling

QualGear QG-PM-002-WHT Projector Ceiling Mount - Mounting to a Brick or a
Concrete Ceiling

Hold the marking template provided against the ceiling where you want to install the projector, mark four holes for drilling.

QualGear QG-PM-002-WHT Projector Ceiling Mount - Using a power
drill

Using a power drill and a 3/8″ masonry drill bit, drill mounting holes of 3/8″ (10 mm) diameter and 2.7″ (70 mm) depth at the marked locations in the previous step.

QualGear QG-PM-002-WHT Projector Ceiling Mount - Place concrete
anchors

Place concrete anchors (W-B) in each hole. Tap each anchor flush with the ceiling surface using a hammer. Mount the ceiling plate and tighten with the lag bolts (W-A) and washers (W-C) using a socket wrench.

WARNING

  • Installers are responsible to provide hardware for other types of mounting situations.
  • Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Installing Adapter Bracket to the Projector

QualGear QG-PM-002-WHT Projector Ceiling Mount - Installing Adapter Bracket
to the Projector

Depending on the mounting hole configuration of your projector, replace the attached extension brackets with the additional extension brackets provided, choose from (M-O/ M-P/ M-Q).
Then, place the projector bracket as close to the center of gravity of the projector as possible, align the holes of the extension brackets over the mounting holes of the projector. Select the appropriate screws (M-C/ M-D/ M-E/ M-F/ M-G) and washers (M-H/ M-I/  M-J/ M-L) according to the mounting holes of your projector, and tighten the screws using a screwdriver.

NOTE
If your projector does not have at least three mount holes, do NOT use this projector mount.
Tighten all screws but do NOT over tighten.

Connecting the Projector Mount Assembly to the Extension Column

QualGear QG-PM-002-WHT Projector Ceiling Mount - Mount
Assembly

Adjustments

QualGear QG-PM-002-WHT Projector Ceiling Mount - Mount Assembly
2

Your projector ceiling mount is now installed.
To make adjustments, loosen up the screws slightly with the alley key (M-M). When you are satisfied with the adjustments, tighten up the screws again

IMPORTANT:
Use an assistant for this step to hold projector securely. Do not loosen screws all the way when making adjustments, this will disconnect the parts and may cause injury or property damage.

Maintenance

Please check that the projector mount is secure and safe to use at regular intervals. If you have any questions regarding any of the instructions or warnings; please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.

QualGear logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

QualGear User Manuals

Related Manuals