QualGear QG-TM-001 Picture Hanging Style Ultra Low Profile TV Wall Mount Instruction Manual

QualGear QG-TM-001 Picture Hanging Style Ultra Low Profile TV Wall Mount

Product Information

• Specifications
  • Maximum Rated Weight: 50kg (110lbs)
  • Designed for: Indoor use only
  • Intended Use: Residential use only

Product Usage Instructions

• Installation Precautions
  • Please read the entire installation manual before starting installation and assembly.
  • Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual.
  • This product should only be installed by someone with good mechanical aptitude, experience with basic building construction, and who fully understands these instructions.
  • Tighten screws firmly, but do not over-tighten as it may damage the items and reduce their holding power.
  • Never exceed the maximum rated weight specified in this manual.
  • Make sure that the supporting surface can safely support the combined load of the equipment and all attached hardware and components.
  • All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.
  • Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
  • Avoid installing near air conditioner vents or in areas with excessive dust or smoke.
  • When drilling holes in the wall, take care to avoid electrical cables, water, or gas pipes in the wall.
• Wall Construction
  • This product is designed to be installed on the following types of wall construction:
  • Wooden Stud
  • Wooden Beam
  • Solid Concrete
  • Brick
  • Other (Contact Qualified Professional)
  • Parts Checklist
  • Before starting installation, please check that all parts shown in this checklist are included.
  • If any parts are missing or damaged, contact your local distributor or support@qualgear.com.
  • For replacement parts do not start assembly and installation until you receive all the parts.
• FAQ (Frequently Asked Questions)
  • What should I do if I exceed the maximum rated weight?
  • Exceeding the maximum rated weight specified may result in serious injury or property damage.
  • It is important to ensure that the weight of your equipment does not exceed the maximum rated weight.
  • If you have equipment that exceeds the maximum rated weight, consider using a different mounting solution that can support the weight or consult with a qualified professional.
  • Can I use this product outdoors?
  • No, all QualGear products are intended for indoor use only. Using the product outdoors will void the limited warranty.
  • Can I use this product for commercial purposes?
  • No, all QualGear products are designed and tested for residential use only. Using the product for commercial purposes will void the limited warranty.
  • What should I do if I encounter any issues during installation?
  • If you have any questions or encounter any issues during installation, please consult the installation manual and ensure that you have followed all the instructions correctly.
  • If the issue persists, you can contact QualGear customer support via email at support@qualgear.com. (for US customers) or reach out to your local distributor (for international customers).

Please read the entire installation manual before you start installation and assembly.

Installation and Assembly

• Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual. If you have any questions regarding the instructions, for US customers please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, who has experience with basic building construction, and who fully understands these instructions.

• This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
  Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.

• ALL QUALGEAR products are intended for indoor use only and any outdoor use voids the limited warranty.

• ALL QUALGEAR products are designed and tested for residential use only and any commercial use voids the limited warranty. For warranty information, please visit http://www.qualgear.com/warranty.php.

• If mounting to wooden studs, make sure that mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is highly recommended.

• Never exceed the maximum rated weight specified in this manual.

• All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.

• DO NOT install near air conditioner vents or where there is excessive dust or smoke.

• When drilling holes in the wall, it is very important to take care of electrical cables, water, or gas pipes in the wall.

This product was designed to be installed on the following wall construction only:

• WALL CONSTRUCTION Wooden Stud
  • Wooden Beam
  • Solid Concrete
  • Brick
  • Other
• HARDWARE REQUIRED
  • Included
  • Included
  • Included
  • Included
  • Contact Qualified Professional

Parts Checklist

IMPORTANT: Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com. for replacement parts and do not start assembly and installation until you receive all the parts.

Hardware Package

Mounting

1a Mounting to a Wooden Stud Wall

IMPORTANT: Minimum VESA for wooden stud installation is 400x400mm. If your TV has mounting holes closer than 400x400mm, do NOT use this mount.

1. Using an edge-to-edge stud finder, find the edges of the stud.
2. Using a level, mark the centerline of the stud.
3. Using the wall plate (A) as a template, mark two holes for drilling on the centerline of the stud.
4. Using a power drill and 3/16″ drill bit, drill pilot holes of 3/16″ (4.5 mm) diameter and at least 2.5″ (65 mm) depth.
5. Mount the wall plates (A) and tighten them with the provided lag bolts (W-A) and D6 washers (W-C) using a socket wrench.

[ Table 1a ] The letter “a” stands for the spacing between the wooden studs. The letter “L” (see step 2) stands for the actual length of the wire rope.

TIP

If your TV has a VESA of 400x400mm and spacing between the wooden studs is 16″, then use wire rope length of 700mm.

WARNING

• Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1b Mounting to a Concrete 1b or a Solid Brick Wall

1. Hold the wall plate (A) as a template against the wall where you want to install your TV, mark two holes for drilling.
2. Using a power drill and a 3/8″ masonry drill bit, drill mounting holes of 3/8″ (10 mm) diameter and 2.7″ (70 mm) depth at the marked locations in the previous step.
3. Place plastic anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer. Using a socket wrench, mount the wall plates and fasten them with the provided lag bolts (W-A) and D6 washers (W-C).

[ Table 1b ] The letter “X” stands for the spacing between the wall plates. The letter “L” (see step 2) stands for the actual length of wire rope.

TIP

If your TV has a VESA of 400x400mm, mount the wall plates at a spacing of 180-220mm, and use the wire rope length of 500mm.

WARNING

• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Installing the Adapter Brackets

To adjust length of wire rope, loosen nuts of clamp (D), adjust wire rope length as necessary and re-tighten the clamp nuts using wrench (F).

Installing to a Flat Back Panel of a TV

Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your TV, and tighten the adapter brackets (B) and the kickstands (C) to the back of the TV using a Phillips screwdriver.

Installing to a Curved or Recessed Back Panel of a TV

Choose the appropriate screws, washers, and spacers (if necessary) according to the type of your TV and tighten the adapter brackets (B) and the kickstands (C) to the back of the TV using a Philips screw driver.

Hanging the TV onto the Wall Plates

Cable Management

Fold out the kickstands to access the cables behind the TV. Once all cables are installed, unfold the kickstands.

Maintenance

• Please check that the TV Wall Mount is secure and safe to use at regular intervals.
• If you have any questions regarding any of the instructions or warnings, please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.
  • www.qualgear.com.
• For Most 37″ to 70″ Flat-screen TVs and Monitors.
• CAUTION! Do not exceed the maximum rated weight specified. Otherwise, serious injury or property damage may occur.
• VESA for Brick & Wooden Walls
  • B 100×100 | 200×200 | 400×400 | 600×600 | 800×800
  • W 400×400 | 600×600 | 800×800
  • 1 Year Limited Warranty
  • Version January 2016

References

• QualGear Warranty On Product Purchase | Qualgear Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>