BEGA 84099K4 Surface Washer Indoors Outdoors Graphite Light Instruction Manual

Table of Contents

BEGA-84099K4-Surface-Washer-Indoors-Outdoors-Graphite-Light-PRO-removebg-
preview

Safety

The installation and operation of this luminaire must comply with national safety regulations.
Only a qualified electrician should carry out the installation and commissioning.
The manufacturer is not liable for damage due to improper use or installation.
Any modifications should be done by authorized personnel.

Q: Can I install the luminaire myself?
A: No, only a qualified electrician should install and commission the luminaire to ensure safety and proper functioning.
Q: Where can I find accessories for the luminaire?
A: Accessories like enterrer, traverse, and sangle are available. Separate instructions for their use can be provided upon request.
Q: What should I do if I need spares for the luminaire?
A: You can find spares such as LED power supply units, LED modules in different colour temperatures, reflectors, and gasket housing by referring to the provided part numbers.

BEGA-84099K4-Surface-Washer-Indoors-Outdoors-Graphite-Light-
FIG-1

Application

Surface washer with asymmetrical light distribution and mounting bush G ½ for illuminating walls, ceilings, ground surfaces and advertising boards.
The floodlight can be bolted together with any female thread G ½ according to ISO 228 supplied by others or to BEGA accessories.

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Safety glass
The reflector surface is made of pure aluminium
Mounting bracket with G½ threaded connection
Thread length: 11 mm
Rotation range surface floodlight 315° Swivel range -30°/+120°
Connecting cable ÖLFLEX ROBUST 210 · 5 G 1 mm²
Cable length 1 m
BEGA Ultimate Driver®
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK08
Protection against mechanical impacts < 5 joule
– Safety mark
– Conformity mark
Wind catching area: 0.07 m²
Weight: 2.8 kg
This product contains light sources of energy efficiency class(es) D

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage under DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

84 099 K4

84 099 K3

Screw floodlight mounting bush G½ firmly into the female G½ thread provided on-site or into BEGA accessory.
Torque of the mounting bush G½ = 20 Nm.
Secure bolted connection against loosening.
Check the earth conductor connection between mounting bush G½ and female thread G½ provided on site.
The electrical connection must be carried out with matching protection class and safety class, strain-relieved, with suitable connection terminals (not included in the scope of delivery) at the luminaire power supply cable.
Note the correct configuration of the main supply cable.
Make connection of the phase with the L marked, the neutral wire at the N marked and earth conductor at the marked wire.
The connection of the control cables is achieved using both leads marked with – DALI –. In case these leads are not used the luminaire will be operated at full light output.
Undo the joint screw and adjust the slope angle of the surface floodlight.
Tighten the joint screw firmly.
Torque = 14 Nm

Please note

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.