sw-motech STP.06.590.10000-B Frame Pads Kit Instruction Manual
- June 2, 2024
- SW-MOTECH
Table of Contents
**sw-motech STP.06.590.10000-B Frame Pads Kit Instruction Manual
**
Mounting Instructions
SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:
| M6 | 9,6 Nm |
|---|---|
| M10 | 46 Nm |
All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts.
Subject to change. Not responsible for typos
STP.00.590.001 02
Pcs. : 2| Frame Slider
---|---
STP.00.590.002 00
Pcs. : 2| Adapter Plate
M6 x 40 DIN 912
Pcs. : 2| Hexagon Socket Screw
LOG.00.000.001 02
Pcs. : 2| Logo Plate
STP.00.590.003 02
Pcs. : 2| Mounting Plate
M3 x 6 Anzahl/ Pcs. GEFU 4| Self-tapping Screw
M10 X 1,25 x 70 DIN 912
Pcs. : 2| Hexagon Socket Screw
Da:20 Di:10,5 h:20
Pcs. : 2| Spacer
Attach part (5), (6) and (7) with the original washer as shown in
step 1. Do not fully tighten screw (6). Adjust the mounting plate (5)
according to the alignment of the motorcycle. Now tighten screw (6). Pay
attention to the manufacturer’s specified torque. Then attach the parts (1),
(2), (3), (4) and (8), as shown in step 2.
Attention : First attach the frame slider on the left side, then on the
right side. Never attach both frame sliders, or remove both engine bolts at
the same time.
Follow the installation steps on the right side of the vehicle.
MOUNTING INSTRUCTIONS
Crash pad set
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable, If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION : Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor/exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING : All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker . Torque specifications
undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a
specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
Scdrit| Nr
No| Item No./Description| Part| Quantity**| N-m “””
1| 1| STP.00.590.020L/R| Crash Pad, left/right| 22|
| | | | |
2| 2| | Logo Insert| 2|
| | | | |
3| 3| | Lenshead Screw, self-tapping| 2/2| max. 1,2
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
Errors and omissions excepted. Technical and design modifications are subject to change.
MOUNTING
Step [1]: Attach the crash pads (1) on both sides to the adapter plates
of your SW-MOTECH slider set for frame, as described in the mounting
instructions of the slider set for frame.
Step [2]: Place the logo inserts (2) on both sides into the crash pads …
Step [3]: … and attach them with the screws (3).
Tighten the screws (3) CAREFULLY by hand (max. 1,2 N-m)!
Errors and omissions excepted. Technical and design modifications are subject to change.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>