LUTRON Caseta Wireless In Wall Switch User Guide
- June 4, 2024
- Lutron
Table of Contents
LUTRON Caseta Wireless In Wall Switch
In-wall switch
Welcome and thank you for purchasing a Caséta Wireless Diva Smart in-wall switch. In order to control your lights from an app or remote, you’ll need to replace an existing switch with a Caséta Wireless Diva Smart in-wall switch. We hope you enjoy the convenience of Caséta Wireless.
Double your warranty
Love Caséta Wireless products? Have ideas for making them better? Tell us
what you think and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
Contents supplied
Tools you’ll need
Installing your switch
Turn power off at circuit breaker!
WARNING: SHOCK HAZARD May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.
Important note: Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). We’ve included instructions for lights with one wall switch (called a single pole). If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way for complete installation instructions and how-to videos.
Remove existing switch from wall
- Remove the wallplate from switch.
- Remove the switch and pull it away from the wall.
- Disconnect all three wires* from the switch.
- If your light has more than one switch (called a 3-way), please visit www.casetawireless.com/3way
Ganging and Derating
Important note: Removing side sections does not reduce the switch’s
maximum wattage rating. See the chart below for maximum load information.
Maximum load derating chart (120 V~ 50/60 Hz)
- The in-wall switch is ULR Listed for use with all magnetic and electronic fluorescent ballasts.
- The maximum lamp wattage is determined by the efficiency of the transformer, with 70%–85% as typical. For actual transformer efficiency, contact either the fixture or transformer manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the in-wall switch.
Connect the switch
- Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the switch using a wire connector.
- Connect the load wire from the wallbox to the red wire on the switch using a wire connector.
- Connect the hot wire from the wallbox to the black wire on the switch using a wire connector.
- Connect the neutral wire from the wallbox to the white wire on the switch (neutral connection required).
Mount the switch
- Use the screws provided.
Attach the wallplate
- Attach the adapter to the switch using the screws provided and snap on the wallplate.
- (If you installed the switch next to other switches or dimmers, you’ll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)
Turn power on at circuit breaker
CAUTION
Use only with permanently installed fixtures with dimmable LED, dimmable CFL,
halogen, or incandescent,lamps. To avoid overheating and possible damage to
other equipment, do not use to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local electrical codes.
To use your Caséta Wireless Diva Smart kit
With a smartphone or tablet (Smart Bridge required, sold separately)
The Caséta Wireless Diva Smart switch can be controlled from a smartphone when
used with the Lutron Smart Bridge. All devices must be within 30 ft (9 m) from
the Lutron Smart Bridge.
- Press and hold “off” button on the switch
- Press and hold “off” button on remote
Using your controls
Replacing light bulbs using FASS
Pull the FASS out on the in-wall switch to remove power at the light socket
Supported Loads
- LED— up to 5 A
- Incandescent/Halogen— up to 600 W
- MLV— up to 600 VA
- ELV— up to 600 W
- Fluorescent— up to 5 A
- General Purpose Fan— up to 3 A
Troubleshooting
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference,and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
For warranty information, please visit:
www.casetawireless.com/warranty
References
- Installing Caséta for a light with two switches | Lutron
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
- Wiring Diagrams | Caséta Wireless | Lutron
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>