CONNEX CM 166 CE PTZ IP Camera Auto Track Indoor Instructions

May 15, 2024
Connex

COXT938768

Instructions

The safety goggles are in conformity with the relevant Union harmonisation legislation:
Regulation (EU) 2016/425 on personal protective equipment (PPE) Directive 2001/95/EC on general product safety The following harmonised European Standard has been used to declare conformity: EN 166 : 2001, EN 169 : 2002, EN 170 : 2002, EN 171 : 2002, EN 172 : 1994 + A1 : 2000 + A2 : 2001, EN 175 : 1997, EN 1731 : 2006.

Marking frame:
CM = Code letters of manufacturer
166 = Number of standard
3 4 = Additional areas of use
S/F/B = Symbol for mechanical strength
CE = EU-Conformity symbol
Do not use frames or safety lenses that do not show a clear marking!

Marking lens:
5 = Welding filter level according to EN 169
UV Transmission until 313nm max. 0,0003%
UV Transmission until 365nm max. 0,3%
5-3,1 = Sunprotection filter according to EN 172
2-1,2 = UV protection filter according to EN 170
CM = Code letters of manufacturer
1 = Optical class
S/F/B = Symbol for mechanical strength
CE = EU-Conformity symbol

Identification

CM 166 CE| mechanical risks
optical radiation according to EN 169
optical radiation according to EN 170
optical radiation according to EN 171
optical radiation according to EN 172
---|---
CM 166 S CE| like above but with clear safety lens marked S for increased robustness = 22 mm ball with 5,1 m/s
CM 166 F CE| like above but with clear safety lens marked F for low energy impact = 6 mm ball with 45 m/s
CM 166 B CE| like above but with clear safety lens marked B for medium energy impact = 6 mm ball with 120 m/s
CM 166 3 4 CE| Protection against liquid splashes (3) and coarse dust (4)

protection against :
clear safety lenses
Welding protection filter level 1,7 to 14
UV-protection filter level 2-1,2
IR-protection filter level 4-6 or 4-7
Sunprotection filter level 5-3,1

Packaging: Transport item only in its original packaging
Accessories: No accessories for this item available
Storage: Store at room temperature in a dry place and clear of dust
Cleaning: With clean water and household detergent (no alkalis, acids or

solvents!)
Avoid strong mechanical cleaning (scratched surfaces) high amount of scattered light)
Disinfection:| Article can be disinfected with all common disinfectants
Disposal:| When disposing of the article, the national regulations must be observed
Adjustment:| Adjustment options of strap or headband use to ensure a secure fit   guarantee
Spare parts:| Only use spare lenses with CE mark and the same marking Install discs with imprint> inside <in the correct direction Check for secure fit of lens after changing Lens must always fit together with marking of frame Always replace filter lenses in pairs because of possible color differences
Use:| Do not use product 5 years after the user‘s purchase date

Warnings:
Do not use glasses after damage! Only use lenses with optical class 1! (optical class 3 is not intended for long-term use!) Materials that come into contact with the wearer‘s skin may cause allergic reactions in susceptible persons! It is essential to replace scratched, dirty, damaged or differently colored discs or supporting bodies! If lens and frames carry different mechanical resistance markings, the lower level applies to the complete eye protection product.
Eyewear against high velocity particles can present a risk of shock transmission when worn over standard prescription eyewear! Only glasses with the abbreviation for mechanical strength FT or BT are suitable for extreme temperatures!
If T in the marking is missing, the eye protection products may only be used at room temperature.
The complete eyewear is only suitable for a specific use, if the marking of the frame and the lens both indicate such use! (Compatibility of the marking!)
Do not repair damaged goggles yourself, but dispose of them!
When using color filters, ensure that there is adequate lighting in the workplace.
Do not use in traffic!

Limitation of use:
In particular, these goggles are not suitable for high speed particles (such as bolt driving tools), laser beams, temperatures over 55% Celsius, arcing faults, molten metals, infectious agents or organisms!
EU Declaration of Conformity: An EU Declaration of Conformity in accordance with PPE Regulation (EU) 2016/425 and the General Product Safety Directive 2001/95 / EC is available on the following website for this product. www.conmetallmeister.de

Zertifizierungsstelle:
ECS GmbH
Hüttfeldstraße 50
73430 Aalen / Deutschland
Notified Body: 1883
Conmetall Meister GmbH
Hafenstraße 26
29223 Celle
GERMANY
www.conmetallmeister.de

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals