Livoo TEC620 Smartwatch User Manual

Livoo TEC620 Smartwatch

Figures

Safety Instructions

Please, take time to read well the instruction sheet before the first use and keep them for a future use.
A misuse of the appliance can damage it or hurt the user. Assure that you use the appliance for the use for which it is designed. We refuse any responsibilities as for the damages by an incorrect use or a bad manipulation.

1. Do not charge after the device was water damaged.

2. This product is an electronic monitoring product. Data received from it cannot be used as medical basis.

3. This device is not compatible with a pacemaker. Do not use this device if you have a pacemaker.

4. Blood pressure testing tip：
   – Keep your body relaxed and still while testing.
   – Keep device at the same height as your heart, and don’t talk while you are testing.

5. A charging environment of more than 50 degrees may cause overheating and deformation of the equipment.

6. This device uses built-in battery. It is forbidden to disassemble it. Please do not drop, collide, squeeze, puncture or cut.

7. When the battery is broken or leaking, avoid contact with eyes and skin. When the situation occurs, do not touch the contact area and rinse immediately with water.

8. Always disconnect the USB cable from the device immediately after use unless it is charging.

9. Use the provided USB cable only.

10. Do not disassemble or reassemble the product.

11. Keep this product out of the reach of children.

12. Keep the device dry
    

Technical Specifications

Input: 5V ⎓ 0.5 A
Battery: 3.7 V ⎓ 220 mAh, 0.814 Wh
Battery life: 15 days in standby, up to 7 days in use Compatible with Android and iOS.
IP67 waterproofing
7 health functions: heart rate, sleep quality analysis, breathing exercise, pedometer, distance travelled, calories burned, activity time.

Warning:
This product is not a medical device and is not compatible with a pacemaker. Watches and their applications should not be used for diagnosis, treatment, or prevention of diseases or illnesses. To change your habits such as exercise and sleep, be sure to consult a qualified medical professional to avoid serious injury. We reserve the right to modify and improve any of the functions described in this manual without prior notice and continuously update the contents of the product. All contents are subject to the actual product.
Please stop wearing the smart bracelet in case of skin allergy or any discomfort.
Adjust the smart bracelet tightness to ensure air circulation

Use of the device

Charging Operation : fully charge the device before the first use. Take the included cable. Connect the magnetic side on the back of the device. Plug the USB side of the cable in an USB port capable of charging your device. When successfully connected, the screen will show that charging is in progress.
You cannot use your device during charging process. Carefully observe the maximum charging voltage of the device (5V) to avoid any damage.
Removing the watch strap : Push the metal switch on the back of the strap to remove the strap.

Button function
Power button (figure 6, button 1): long press = switch on/off. Short press = Start the screen/return/stand by. In the main menu, double press to change the interface. Double press in home screen to initiate the voice assistant.
Sport button (figure 6, button 2): short press in home screen to enter sports mode.

Downloading & paring (Figure 2)
Start your Smartwatch with a long press on the on/off side button (figure 6, button 1).
Download and install the application “RDFit” on your mobile by using QR code in this instruction manual, in the watch (parameters, QR Code) or by searching the application directly in AppStore or Google Play.

Paring

WARNING: YOU HAVE TO MAKE TWO OPERATIONS TO FULLY CONNECT YOUR DEVICE AND YOUR MOBILE !
OPERATION 1
Once you’ve download and install the application on your mobile device, please follow the instruction of the application to setup it as you prefer and according to your personal information.
Activate the Bluetooth on your mobile device.
Launch the app and select “Connect the device” in “Device interface” (figure 8). The device should appear on the screen of your mobile. Select the device in the list and follow the instruction of your mobile.

OPERATION 2
Go to the setup menu in your device. Select “Bluetooth for calling” and validate it (Figure 7).
In your mobile, check the list of the Bluetooth devices you can select. A second device has appeared in the list named ‘TEC620-Call’. Connect your mobile with this device too to activate all the functions of your device.

Note: Bluetooth devices can only be paired individually, so be sure to disconnect the previous Bluetooth device when connecting a new device. If the Bluetooth icon 3.0 or 5.0 Is colored, connection is successful.
Note 2 : if you choose to disconnect the device and your mobile, do not forget to also “forget” the device in the Bluetooth parameter setup of your mobile.
How to set up the incoming notification message?
1. On your mobile, open RDF it. In the “Device” interface, select “push of the messages”. In this menu, you can enable your mobile to send selected notification on your device. Do not forget to save your setting before quitting the menu.

Note 1 : If the WeChat WEB is online at the same time, the Smartphone will not receive Incoming message notification. For some Smart- phones, you need to whitelist “RDFit” in the power saving mode, to avoid being turned off by the phone when the battery is low.
Note 2 : To receive all notification on your smartphone be sure that the notifications are enabled for the APPs in smartphone settings (steps mentioned above).
Navigate in the menu with your watch: (Figure 3)
When your device is of, push the on/off button to activate it and let it show the standby screen. Click on the screen to enter the main menu, and swipe to the right to return to the standby screen.
Click to enter the corresponding function interface and swipe right to return to the main menu.
Swipe down to the screen control and swipe up to return.
Swipe up to enter the message interface and swipe right to return.
Swipe right to enter the split screen interface and swipe left to return.
Slide left to enter the “adding function” interface. In this interface, you can freely add and delete short access to some app. Swipe right to return.

Device applications
Step-counting : the step-counting interface shows steps. Wear the smart bracelet on wrist, and the smart bracelet can automatically count steps, distance and calories.
Message: seven messages can be saved and seen directly on the device. The new messages will replace the oldest one by one. You can delete a message or a call notification touching it for several seconds.
Calls: once your device is fully connected, you can take calls directly on your watch, talk thanks to the microphone in it and hear the discuss thanks to the speaker in it.
Music: the watch can control the music player of the mobile phone. When the mobile phone plays music, use the music application on your device to control the application on your mobile. Heart rate measurement : the heart rate measurement application supports real- time dynamic heart rate. Be sure that there is no dirt at the bottom of the heart rate sensor when you run a measurement. Skin colour, hair density, tattoos and scars may affect the accuracy of the measuring results, in which cases please re-measure the heart rate.
Note: The heart rate sensor shall be closely attached to skin and well contacted with skin in measurement of heart rate.
Stop watch : Open this application to perform single or multiple timing.
Sleep: from 9 o’clock every night to 9 o’clock the next morning, wearing the smart bracelet at night will allow the watch to detect if you are asleep, to record deep sleep and light sleep respectively and to summarize the total sleep time to help you monitor your sleep quality. The sensor will measure your sleep quality according to the range and frequency of wrist movements when you sleep.
Motion : The watch can select multiple sports modes for sports: walking, indoor running, outdoor running, cycling, mountaineering. After the sports are completed, the data can be displayed on the app.
Find a phone : when your mobile and the watch are connected, launch the application on the watch to let the mobile ring.
Split screen : Swipe toward the right on the dial screen to access the split screen function to quickly access an application.
Dial push: push dials, digital dials and customised dials from the app.
Dial: Connects to your phone with Bluetooth and dials out a call to make a call on the watch.
Call history: can synchronise the call history on the mobile phone.
Contacts: 20 contacts can be synchronised on the mobile phone.
Alarm clock: Up to five alarms can be added via the app.
Remote photo taking : on your mobile, launch the menu “Photo” in RDFIT application. The screen on your watch will show a white button. By clicking on the button, you take a picture with your phone.
Find the device : In RDFit App on your mobile, launch “Find the device” to make the watch ring and vibrate.
Weather : After connecting to Bluetooth, the watch can display the weather condition of the day.
Breathing : You can set the length of time of the exercise and the breathing speed.
Calculator : You can enter the calculator to do simple calculations.
Menu style : From the list provided, you can select the style of menu presentation you want to use.
Business card: The watch connects to the App and can push business cards from the App: WeChat, QQ, Alipay, Weibo, WhatsApp, Twitter, LinkedIn, Instagram, Facebook, Line, Tim, Snapchat, Viber and other third party apps to the watch, so you can add new friends anytime, anywhere.
Wallet: The watch is connected to the app and you can send WeChat, Alipay, PayPal and other third party app codes to your watch, so you can send money anytime, anywhere. More settings. Click Settings to enter the Settings page which displays functions such as language, APP download, product information, factory settings restoration, dials, screen off time and vibration intensity.

Cleaning and maintenance

Wipe your cable with a dry cloth. If not use, store in a dry place away from dust and humidity.

We, DELTA, BP61071, 67452 Mundolsheim – France

Declare under our own responsibility that the article :
– Description : Smartwatch ; – Reference : TEC620
to which this declaration applies, is in conformity with the applicable EU harmonization legislation.

ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-17 V3.2.4 (2020-09)
EN 55032 2015+AC 2016+A1 2020+A11 2020
EN 55035 2017+A11 2020
ROHS 2011/65/EU| The object of the declaration described above is in conformity with Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. EU 2011/65/EU et EU 2015/863

Mundolsheim le 25/01/2023

David Bousquet, CEO

Correct disposal of the unit (Electrical and Electronic Equipment). (Applicable in the European Union and the rest of Europe that have adopted separate collection systems countries). The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be
disposed of in the normal household waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The symbol of the crossed out dustbin is marked on all products to remind the obligations of separate collection. Consumers should contact their local authority or retailer for information concerning the correct disposal of their product.

References

• Livoo, life in feel-good mode

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>