GOPLUS JZ10050 Gun Safe Adjustable Gun Racks User Manual

USER’S MANUAL
Gun Safe

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

JZ10050 Gun Safe Adjustable Gun Racks

Before You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

IMPORTANT
Tip Over Hazard: Secure the safe! A child or adult can tip the safe and be seriously injured.
Do not store the back up key, your combination code or this document in the safe.
Keep keys and combination code in a secure place away from children.
Do not move this safe using its handle.
Record the serial number on the keys or/and serial number from the tag on the front bottom corner of the safe!

SCHEMATIC DRAWING OF CONTROL PANEL

BASIC OPEATION

OPEN SAFE WITH THE EMERGENCY KEY
Upon first use of the safe, or either the electronic circuit malfunctions or codes unknown, you could also use the emergency key to open the safe.

1. Remove the cover of Emergency Lock.
   Insert the emergency key, turn it counter-clockwise.

2. Rotate the Wheel on the Control Panel clockwise.

3. Turn the Door Handle clockwise to open the safe.

INSTALL BATTERIES
Remove Battery Compartment cover.
Insert 4*AA batteries and restore battery cover.
NOTE: If the batteries are low, both of the red and green lights will be on at the same time. You should insert new batteries.
NOTE: When outage for longer than 30 minutes, the user code will become the factory code “111” “123”, you should reset the user’s code.

1. Turn the Door Handle and CLOSE the door.
2. Then rotate the Wheel on the Control Panel counter-clockwise to LOCK the safe.
   (IMPORTANT) BEEP SOUND OPTIONS
   Beep OFF/ON: Press and Hold the Button “2” for several seconds.

FINGERPRINT REGISTRATION

Situation 1: Upon first receipt of the safe. If it can be opened with ANY fingerprint(s), please refer to the part ” OPEN SAFE WITH THE EMERGENCY KEY”.
Situation 2: If safe can NOT be opened with any fingerprint(s), Press and Hold Fingerprint Reset Button for 5 seconds until a continuous sound is heard. Now all fingerprints are deleted. You can register your fingerprints. (The Reset button is inside the safe under the hinge-look)

FINGERPRINT REGISTRTION (IMPORTANT)

1. Press the Fingerprint Reset Button (DO NOT hold the button), followed by a short beep and the green light on.
2. With green light on, place your finger on the scanner. When it beeps (1-2 seconds after placing finger on reader), remove your finger.
3. Place the same finger back on the scanner at the same position for a second time until it beeps again (1-2 seconds). Remove your finger. Your fingerprint is now saved.

Successful Registration: Registration is successful when a consecutive beep is heard.
Unsuccessful Registration: Many beeps will be heard. Green and red lights will flash together.

NOTE: If Registration is unsuccessful, place the same finger on the scanner soon until registration is successful.
To register another fingerprint – repeat FINGERPRINT REGISTRTION (IMPORTANT)
(You can record up to 100 different fingerprints)
TIP 1: To improve the accuracy of a certain finger, we recommend that you register the same finger in different position/directions.
TIP 2: In certain dry climate condition, your fingerprint may not scan. If your fingerprint did not scan, we recommend moisturizing with minimal lotion again. For best results, each individual should use their thumb or index finger only.

OPEN THE SAFE USING YOUR FINGERPRINT

1. Place a record finger on Fingerprint Scanner. The green light will be on with a beep.
2. Rotate the Wheel on the Control Panel clockwise within 5 seconds.
3. Turn the door Handle clockwise to open the safe. If the finger is not recorded, the red and green light will flash together with beeps on.

NOTE: Test Registered fingerprint and multiple Non-Registered fingerprints to see if your new registered fingerprints work or not.
Registered Fingerprint: When safe locked, place the finger and a beep will be heard, green light will be on and you rotate the wheel to the end and open the door.
Non-registered Fingerprint: When safe locked, place the finger and long beep will be heard, the red and green lights flash together. You CAN’T rotate the wheel clockwise to the end and open the door.

SETTING THE USER CODE

This safe can record two user codes. (preset codes are “111”, “123”)
Reset user code: Before setting the user code, press the Code Reset Button (Red Button), followed by a continuous sound and the green light will flash once. Now the user codes are preset codes “111” , “123”.

CHANGE THE USER CODE

1. Press and hold the Number “1” for 5 seconds until the green light comes on.
2. Input preset code “111”, and press “#”. A short beep will be heard and the green light will be on for a few seconds.
3. Input your new user code and press “#”.
4. Then reinsert the same new code and “#” again. Then it will be your new code.

If the green light is on, it means the code changing is effective. If the red and green light flash together, it means the code changing is not effective, and you need to try again.
Repeat step 1,2,3,4 to reset the other preset code “123”.
NOTE: If you hold down the reset button for about 5 minutes, all fingerprints will be deleted, also the code will become default code “111” and “123”.

OPENING DOOR WITH PRESET CODE OR YOUR NEW CODE
Input your user code (3-8 digits) and the “#” button, the green light will be on.
Rotate the Wheel on the Control Panel clockwise within 5 seconds. Turn the Door Handle to open the door.

MOUNTING INSTRUCTIONS

For optimal safety and security, the safe must be mounted to the wall or to the floor in an isolated, dry and secure area.
Place the safe in the desired location. Lift the bottom carpeting up to find the locations of the two holes marked on the floor or wall.
Drill holes for expansion bolts (or clamping screws) in the right place. Drill the appropriate diameter and depth of pilot holes depending on the type of hardware. (12mm diameter holes and depth >54mm,(2.13 inch) for included bolts.)
Turn the expansion bolts counter-clockwise to separate. Use the expansion bolts (or clamping screws) to secure the case to the wall. Make sure the case is mounted in place as required and then tighten all screws.
NOTES: This safe must be mounted to the floor or the wall. Failure to do so will compromise the safety and security of the safe, and it may tip over.

CARE AND MAINTENANCE

To maximize the security and performance of the safe, keep
Fingerprint Scanner clean; use a dry cloth to remove any smudges or prints off the Fingerprint Scanner after each use.
Test registered fingerprints every 6 months.
Keep liquids away from the control panel. Spills on the control panel will cause damage.
Secure safe in a proper area to prevent from falling and causing damage or injury.
DO NOT disassemble the products.
Clean with a damp cloth. DO NOT use chemicals or cleaning agents to clean the safe.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>