sw-motech HTA.01.843.10000 SLC Side Carrier Left Installation Guide

sw-motech HTA.01.843.10000 SLC Side Carrier Left

Product Specifications

• Model Numbers: HTA.01.843.10000, HTA.01.843.11000BC.HTA.00.677.10000L/B, BC.HTA.00.677.10000R/B
• Part Number: BC.HTA.01.843.30000/B

Installation

1. Ensure the area where the product will be installed is clean and dry.
2. Identify the appropriate model number for your specific product variant.
3. Follow the detailed installation steps provided in the user manual.

Operation

1. Power on the product using the designated power button.
2. Adjust settings as per your requirements using the control panel.
3. Refer to the user manual for specific operational guidelines.

Maintenance

1. Regularly clean the product surfaces with a soft, damp cloth.
2. Avoid using harsh chemicals or abrasive materials during cleaning.
3. Check for any loose components and tighten them ifnecessary.

Frequently Asked Questions (FAQ)
Q: What should I do if the product does not power on?
A: Check the power source and ensure it is properly connected. If the issue persists, contact customer support for assistance.

 INSTRUCTIONS· READ AND SAVE THESE MOUNTING INSTRUCTIONS

SLC side carrier

Thank you for choosing this premium product from SW-MOTECH. Please carefully read and understand all instructions, safety messages and warnings in this mounting instructions prior to installation and use of this product to avoid injury.

This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!

SAFETY ALERT SYMBOL

A This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:

• A DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
• A WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
• A CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
• & NOTICE: Important information, but not death or injury related (property damage only)!
• A WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications.
• For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
• A WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during intallation and use. IF YOU DO NOT UNDERSTAND ANY PART OF THESE

INSTRUCTIONS, OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO

MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.

• PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
• A CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
• MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
• A WARNING: Secure all threads, unless otherwise specified, with medium­strong strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
• FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
• A WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.

SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg Germany

Tel. I phone + 49 (0)6425 / 8168 – 050
Fax/ fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com www.sw-motech.com

Errors and omissions excepted. Technical and design modifications are subject to change .

PARTS LIST · READ AND SAVE THESE MOUNTING INSTRUCTIONS

Note: No torque All measurements specifications: in Use the millimeters. torque b The defined second by vehicle number indicates manufacturer! the total The quantity standard of the torque part in in this the table delivery. can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING· READ AND SAVE THESE MOUNTING INSTRUCTIONS

PRODUCT SPECIFIC INFORMATION

A WARNING: It is essential to observe the country-specific regulations regarding the lighting equipment (reflectors)!
If the reflectors mounted to the vehicle in the factory setting are covered by the side carriers, the reflectors must be removed and/or attached elsewhere in the same mounting position!
& NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

MOUNTING INSTRUCTIONS

URBAN ABS side case

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and / or servicing carried out by a specialist workshop! SW-

MOTECH assumes no liability for damage caused by improper installation and/ or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/ or stability of your vehicle.

GENERAL INFORMATION

Observe the country-specific regulations concerning vehicle registration / operation as well as TUY regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

PRODUCT SPECIFIC INFORMATION

• ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
• ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
• ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!

ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!

• All measurements in millimeters.
•  The second number indicates the total quantity of the part in the delivery.
•  No torque specifications: Use the torque defined by vehicle manufacturel’! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

Care

• To clean the side case, use warm, soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer!
• Clean the side case after riding in salty conditions, to avoid damage from salt.
• Hard to open zippers can be loosened with a small amount of talcum powder.

ATTENTION: Surface materials can experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this.

MOUNTING

Place the three locking openings of the side case onto the guide bolts of the mounted SLC side carrier. Then press the side case slightly downward, until it properly rests on the SLC side carrier.

ATTENTION: Make sure that all three guide bolts engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism and that the red marking under the slider is not visible!
To release press the slider downward.

ATTENTION: All components of the side case must not contact any hot or moving parts of the vehicle! All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream! After mounting, make sure there are no clearance issues while the suspension is both compressed and extended. 

Use the included waterproof innerbag (3) to protect your luggage from moisture.

For an easier loading of the side case (11. open the buckles and hook and loop fasteners of the opening reductions, as shown in the drawing.

ATTENTION: Make sure weight is evenly distributed between the left and right side if you want to use both side cases! Make sure that the loanding is secured against shifting during the ride!
ATTENTION: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/side case!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>