GREENBRIDGE PHT401 Pneumatic Strapping Tool Instruction Manual

May 15, 2024
GREENBRIDGE

GREENBRIDGE-LOGO

GREENBRIDGE PHT401 Pneumatic Strapping Tool

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-PRODUCT

Product Specifications

  • Tool Size: Length: Width: Height: Weight:
  • Maximum Tension Force:
  • Tensioning Speed:
  • Sealing: Friction weld seal
  • Air Required: Pressure range: 4.5-7 bar / 64-99 psi
  • Joint Strength: Level sound emission. Measurement type A (2003/10/CE)
  • Vibrations at Handle: (2002/44/CE)

Product Usage Instructions

Safety Instructions
Before operating the tool, ensure to read all safety instructions carefully. When using the tool, always wear eye, face, and hand safety protection. General safety instructions for compressed air should also be followed, including using dry, clean, and lubricated compressed air within the specified pressure range.

Warranty Conditions
The manufacturer provides a warranty for the tools and battery chargers for a specific period from the shipping date. Wear parts have a separate warranty period. Refer to the spare parts list in the tool manual for more information.

Installation
Properly connect the tool to the air supply as per the installation instructions provided in the manual.

Operating Elements and Adjustments
Adjust the welding-cutting time and strap tension using the provided adjustments. Always ensure there is a strap in place before operating to prevent damage to the tool components.

Operation
When operating the tool, follow these steps: Push tension lever no.1 to reach the required tension, release lever no.1, then push lever no.2 to cut and weld the strap. Wait for 2-3 seconds after the welding cycle to cool the strap before removing the tool.

Seal Check
Regularly check the seal quality visually to ensure proper sealing of the strapping.

Frequently Asked Questions (FAQ)

Q: What should I do if the tool does not operate properly?
A: If you encounter any issues with the tool’s operation, refer to the troubleshooting section in the manual or contact customer support for assistance.

Q: How often should I lubricate the tool?
A: It is recommended to lubricate the tool according to the maintenance schedule provided in the manual to ensure smooth operation.

SAFETY INSTRUCTIONS

READ THE OPERATING INSTRUCTION CAREFULLY

WHEN OPERATING THE TOOL, WEAR EYE, FACE AND HAND SAFETY PROTECTION

GENERAL SAFETY INSTRUCTIONS :

The tool must be used by properly trained people. Failure to follow the operating instructions or improper use could cause strap breakage, injuries, or package damages.
Check tool daily, do not use tool with worn or damaged parts. Use original spare parts for replacement. Never modify any tool part.
Do not put fingers, hands or other body parts between the strap and package during the cycle.
It is your responsibility to check the seal joints made by your tool. Training about the weld time adjustment will be useful to check the seal quality in order to avoid severe injury. Never move goods with bad quality seals. Only use specific strap dispenser to dispense the strap. Keep your working area clean and always use the tool in good balance and safety conditions. Never use straps as a means of pulling or lifting goods.
Always use a proper safety strap cutter and keep other people and yourself at a safe distance from strap, always stand to side of strap, away from direction of strap trajectory once cut. Hold the upper strap portion and pay attention that the lower strap will snap forward away from you.

Improper operation, excessive tensioning, use of non-recommended strap, or sharp corners on the package could cause a loss of strap tension and/or strap breakage that could lead to packaging failure or injury. The following is recommended; use edge protectors if package has sharp corners,place the strap correctly around a properly positioned package, stand in safety position (on one side of strap) during strapping cycle, and use the correct strap quality, width, thickness, and break strength as recommended in this manual.
Please save this manual, as it is a part of the tool. This tool is manufactured without any substances which could be dangerous to health. National instructions must be observed for disposal of all the parts.

GENERAL SAFETY INSTRUCTIONS FOR COMPRESSED AIR:
Never operate this tool using a bottled air or other gas source. Do not exceed the air pressure range as shown in this operation manual. For all adjustments, repairs or cleaning of the tool, always disconnect air supply. Always use dry, clean and lubricated compressed air.

TECHNICAL DATA

TOOL SIZE:|
---|---
Length:| 280mm – 11”
Width:| 150mm – 6”
Height:| 175mm – 6.9”
Weight:| 4.9 kgs – 10.8lbs


AIR REQUIRED:

|
---|---
Pressure range:| 4.5-7 bar / 64-99 psi
Air consumption:| 14 L/s – 29cuft/min
SPECIFICATION|
---|---
Maximum Tension force:| *2500N – 6.5 bar – 92 psi
Tensioning speed:|
11 mt/min**


Sealing:

| ****

Friction weld seal


Joint strength:

| ****

**80% plastic strap strength***

Level sound emission. Measurement type A (2003/10/CE)| ****


77 dB (A)

Vibrations at handle (2002/44/CE)| ****

< 2.5 ms2

depends of kind strap

CHART OF TYPES

ITEM MODEL STRAP THICKNESS
T101013 PHT401 * PP-PET -3/8” >.016” – 0.047”<
T101313 PHT401 * PP–PET -1/2” >.016” – 0.047”<
T109913 PHT401 * PP-PET -5/8”-3/4” >.016” – 0.047”<

Only with clutch on tensioning

WARRANTY CONDITIONS

Greenbridge warrants all its tools and battery chargers during a period of 6 months from the shipping date document. Wear parts are warranted for 45 days, otherwise wear parts are excluded from regular warranty,wear parts are shown on spare parts list (in tool manual).
Warranty includes free replacement parts. The warranty is not valid in case of improper use, lack of maintenance, tampering, arbitrary modifications and reparations, use of non-original parts, disregard of instructions of the operation manual, or missing serial number. No compensation can be claimed for production shutdowns and for damages to people and objects due to tool defects. Greenbridge reserves the right to modify the tools and documentation without any obligation to update previous ones.

Greenbridge warrants all its batteries during a period of 120 days from the shipping date document. The manufacturer is committed to replace it with a free battery only when there are manufacturing defects that make it unfit for use.

INSTALLATION

It is recommended to always use a dryer unit near the compressor and a filter- regulator-lubricator unit with pressure gauge (Greenbridge part # 200-0025) close to the tool air connection to avoid water and dirt in the valves or in the pneumatic motors. Connect the tool to air with quick connector ¼” and use minimum 8mm or 3/8” internal diameter pipe; max length for flexible pipe 10 m between tool and regulator group. Check that your compressor / air distribution plant is able to supply the right air quantity as shown in the operation manual without losing pressure.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(1\)

OPERATING ELEMENTS AND / ADJUSTMENTS

DO NOT OPERATE THE TOOL WITHOUT STRAP, YOU COULD DAMAGE THE FEED WHEEL AND THE WELDING / CUTTING GROUP

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(2\)

Welding – cutting time adjustment
The welding time can be adjusted with a screwdriver (pic.A), depending on strap quality and dimensions. Turning clockwise will increase the time, turning counter clockwise will decrease the time

Adjusting strap tension by motor
The strap tension can be adjusted with a screwdriver on the pneumatic motor, depending on strap quality and dimensions. (pic.B). Turning clockwise will reduce the force, turning counter clockwise will increase the force – do not exceed in counter clockwise.

Adjusting strap tension by clutch
The strap tension can also be adjusted with clutch system (pic.C). Turning the nut clockwise the force will be increased, turning counter clockwise it will be reduced – do not exceed in both directions –

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(3\)

Feed Wheel gap adjustment
It is possible to adjust the gap between feed wheel and grippers in order to change the teeth pressure on strap; unscrew the locking screw 1(pic.D1) and turn screw 2 (pic.D2), clockwise the gap will be increased, counter clockwise the gap will be reduced. Screw 2 pushes against the gearbox housing pin (pic.D3). After adjusting, lock screw 1 again. The standard gap is 0.2mm (0.008”) (pic.D4).

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(5\)

Strap size conversion
To set the tool for (13mm, ½”) – (16mm, 5/8”) – (19mm, ¾”) strap sizes, follow the instructions below:

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(6\)

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(7\)

OPERATION

The tool model PHT401 is designed to strap packages with plastic strap. The strap is fed around the package manually and inserted in the tool, tensioned, cut, and friction welded by the tool. Wrap the package to be strapped with the strap, as shown in pic.F1. Open the tool by squeezing the lever and motor together with right hand and insert the two straps. Make sure they are aligned between the body and bottom plate and against the front / rear strap guides (pic.F2). Release the lever. (pic.F3).

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(8\)

Push tension lever no.1 until required tension or maximum force (motor stalls) is reached, as shown in pic.F4, release lever no.1 and push lever no.2 (do not hold down) (pic.F5) to cut and weld the strap.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG- \(9\)

Seal check
A regular seal quality control is very important and it can be checked visually as follows:

  • G1) Sealing time set too low
  • G2) Sealing time set correct
  • G3) Sealing time set too long

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(10\)

SERVICING – CLEANING

Disconnect the air line from the tool before performing any service.
Periodically clean the tool from strap dust, particularly the feed wheel, the gripper plates and the cutter by using compressed air or wire brush (do not use other tools or objects) (pic. H1,H2)

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(11\)

Cutter replacement
Disconnect the air pipes from welding motor and tension motor (pic.L1), remove the opening lever screw and remove the opening lever (pic.L2), remove 3 pneumatic valve screws and remove the valve (pic.L3) remove the 2 locking welding motor screws (pic.L4), remove the motor (pic.L5).Pull out the cutter spring with pliers (pic.L6), insert air into the disconnected pipe to push down the piston and free the cutter and remove it with pliers (pic.L7). Replace it and reassemble in reverse order putting grease on spring and cutter seat.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(12\)

Feed Wheel replacement

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(13\)

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(14\)

Remove the pushing spring (pic.M1), disconnect the motor pipe (pic.M2), remove the 6 bottom plate screws (pic.M3), unscrew the holding screw (pic.M4), remove the nut on connection shaft (pic.M5) and pull it out from main frame (pic.M6) pay attention to the shim. Remove the feed wheel shaft nut (pic.M7) Remove the front cover, the bush, the clutch system with the feed wheel (pic.M8); replace the worn part (pic. M9) Reassemble in reverse order.

Bottom plate grippers replacement
Remove the 6 bottom plate screws (pic.N1), unscrew the grippers screws (pic.N2), replace the parts (pic.N3), and reassemble.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(15\)

Welding gripper replacement
Remove the cutter as shown in L1 to L5 sequence, remove the bottom plate as point N1, remove the safety circlip from welding gripper pin (pic.O1), remove the pin from welding gripper (pic.O2), and replace the worn out part (fig. O3). Reassemble all parts in reverse order.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(16\)

TROUBLESHOOTING

PROBLEM

REMEDY
Insufficient strap tension
Check the following: air pressure value (min.4.5 bar), if the filter / lubricator and/or the pneumatic motor is damaged or dirty, the pneumatic circuit, tension button, connections, pipes, valve. – Check if the clutch is loose.
The feed wheel slips and mills the strap
Check if the feed wheel and grippers are dirty or damaged. Adjust the gap between feed wheel and grippers (around 0,2mm– 0.008”). Adjust the motor power—too much tension force.

Check if the strap qualities are right for the strapping tool and application

The strap is breaking during tension
Adjust the motor power—too much tension force. Check if the strap qualities are right for the strapping tool and application. Check package for sharp edges.
The strap is sideways after tensioning; The seal isn’t in the middle of strap width
Adjust the motor power—too much tension force. Check if the strap qualities are right for the strapping tool and application. Check strap size; Check the strap guides for alignment.
The lower strap isn’t locked between the grippers and feed wheel so the tool goes forward during thetension
Adjust the gap between feed wheel and grippers (around 0,2mm– 0.008”). Check if the locking strap plates are dirty or damaged. Adjust the motor power.
Strap locks against itself
Adjust the gap between feed wheel and grippers (around 0,2mm– 0.008”)- try to increase the gap.

Check if the strap qualities are right for the strapping tool and application.

Tool is leaking air

Check the gaskets and pipes, replace if necessary
The strap does not seal; the upper strap isn’t completely cut; the cutting is inconsistant
Improper weld time adjustment. Check if the sealing foot and the cutter are damaged or worn out.

Check if the sealing foot slides on strap. Check the air pressure value.

Check if the strap qualities are right for the strapping tool and application. Check if the sealing motor is locked or dirty and, the pneumatic valve – try to clean the timer valve. The cutter spring is damaged, try to replace it.

Strap is over-sealed; the strap is breaking during the sealing – cutting
Improper weld time adjustment, may be too long.
During the sealing both straps are cut
Check if the gripper plate (under the sealing foot) is dirty or damaged (clean or replace it) Check if the strap is over tensioned. Improper weld timing adjustment, may be too long.
After the cycle is not possible to remove the tool from package
Check if there is too much tension. If it is not possible to remove the tool by hand, cut the strap from package and disassemble the foot from the main frame to remove the strap.
The sealing time will not remain constant
Timer valve problem, try to clean, lubricate or replace it.

LAYOUT-SPARE PARTS LIST

Ed. 06/17

GREENBRIDGE PART #| ITEM| DESCRIPTION| QTY| |
---|---|---|---|---|---
189604| A000014| ASSEMBLED GEARBOX BODY| 1| |
189570| A000086| ASSEMBLED FRONT COVER| 1| |
186897| B100032| PLASTIC PIPE 6×8| 0,09| |
189122| B100296| GRUB SCREW 1/4″ S2610 CAMOZZI| 1| |
189137| B100310| SWING ELBOW RL31 8 1/4| 1| |

189185| B100313| AIR FITTING 1/4”| 1| |
189599| B100403| SPIRAL PIPE 6×8| 0,25| |
189105| B200309| FAST AIR MALE CONN. APAG261.14| 1| |
189212| B200357| PNEUM.VALVE 3/2| 1| |

189177| B300021| O-RING 2125 (D32)| 1| |
189471| B300022| O-RING 3300 (D85)| 1| |
189296| B300055| O-RING 2043| 1| |
189508| B300451| O-RING 4300 N| 2| |
189180| B400001| ROLLER BEARING BK0810| 1| |
189182| B400002| BEARING 7200BE 2RS| 1| |
189146| B400003| ROLLER BEARING HK0808| 2| |
189176| B400004| BEARING 6001 2Z| 2| |
189149| B400005| ROLLER BEARING NK1616| 1| |
189198| B400008| BEARING 6001 2RS| 1| |
189166| B400009| BUSHING RING IR 12x16x16| 1| |
189574| B400340| AXK1226 SKF| 1| |
189575| B400341| AS 1226 SKF| 2| |
190196| B500037| SCREW M4X8| 1| |
189136| B500039| SCREW UNC 10X1/2″| 9| |
189179| B500043| SCREW ECOFIX M5X12 ZINC| 2| |
189276| B500045| SCREW M4X5| 1| |
189698| B500047| SCREW M5X8| 2| |
189438| B500048| SCREW M4X6| 3| |

189800| B500050| SCREW M4X35| 3| |
189163| B500053| SELFLOCK.NUT M8 H10 DIN982| 1| |
190161| B500068| SCREW M3X8 UNI5931| 2| |
189576| B500071| SCREW M8X6 UNI5923L| 1| |
189783| B500138| SCREW UNC 1/4X5/8 ANSI| 5| |
190147| B500211| SCHNORR WASHR DIAM.4R| 2| |
190044| B500379| SCREW STEI M4X5 UNI5923| 1| |
189785| B500407| SCREW UNC 1/4X1/2 ANSI B18.3| 1| |
189982| B500456| SCREW UNC 10-24X5/8| 1| |
189192| B600011| WASHER PS 10x16x0.5| 1| |
189183| B600012| CIRCLIP A10 DIN471| 1| |
189153| B600013| CIRCLIP 5 UNI 7434| 1| |
189193| B600014| WASHER PS 22x30x0,1| VAR| |
189194| B600015| WASHER PS 22x30x0,5| VAR| |
189279| B600016| WASHER PS 10x16x1| 1| |
189476| B600028| SPRING R10-051 ISO 10243| 1| |

189170| B600059| CUP WASHER CB25x12.2 x 1.5| 3| |
189579| B600338| GUIDE SOCKET BM 12 14 25| 1| |
189580| B600342| GUIDE SOCKET BM 16 18 10| 1| |
189767| B600389| WASHER PS 22x30x0,2| VAR| |
---|---|---|---|---|---
189501| B700031| PIN 3×60 DIN6325| 1| |
189581| B700078| PIN 6X18DIN6325| 1| |
189668| B700427| ELASTIC PIN 5×16 UNI6874| 1| |
189134| B900348| PNEUMATIC WELD MOTOR| 1| |
189215| B900353| PNEUMATIC TENSION MOTOR| 1| |
189132| D000620| CUTTER BLADE SPRING| 1| |
189157| D000780| LOCKING STRAP PLATE| 1| §|

189151| D001250| WELDING FOOT| 1| §|
189133| D001260| CUTTER| 1| §|

189282| D001620| CONNECTING ROD PIN| 1| |
189150| D001630| CONNECTING ROD| 1| |
189482| D001640| EXCENTRIC SHAFT| 1| |
189152| D001650| WELDING FOOT PIN| 1| |
189478| D001670| OPENING LEVER| 1| |
189160| D001700| WELD TIMER COVER| 1| |
189121| D001710| PISTON SPRING| 1| |
189178| D001730| GEARBOX COVER| 1| |
189484| D001740| CROWN| 1| |
189181| D001750| WORMGEAR| 1| |
189174| D001760| FEEDWHEEL SHAFT| 1| |
189172| D001770| SHAFT| 1| |
189190| D001780| SPECIAL NUT| 1| |
189586| D001800| REAR STRAP GUIDE 5/8” 3/4”| 1| |
189587| D001810| SIDE STRAP GUIDE 5/8”| 1| |
189588| D001820| SIDE STRAP GUIDE 3/4”| 1| |
189589| D001830| TENSION START LEVER| 1| |
189590| D001840| WELDING START LEVER| 1| |
189592| D001870| SUSPENSION HOOK| 1| |
189143| D001880| SIDE SUSPENSION HOOK SUPPORT| 1| |
189140| D001890| UPPER SUSP. HOOK SUPPORT| 1| |
189594| D001910| SPRING PIN| 1| |
189595| D001920| REAR STRAP GUIDE 3/8” 1/2”| 1| |
189596| D001930| SIDE STRAP GUIDE 1/2”| 1| |
189601| D001940| SIDE STRAP GUIDE 3/8”| 1| |
189763| D001960| REAR FRICTION PLATE| 1| |
189168| D001970| FRICTION PLATE| 2| §|
189169| D001980| FEEDWHEEL| 1| §|

189167| D001990| FRONT FRICTION PLATE| 1| |
189602| D002380| PISTON COVER| 1| |
189597| D003970| FRONT STRAP GUIDE 3/8” 1/2”| 1| |
189598| D003980| FRONT STRAP GUIDE 5/8” 3/4”| 1| |
189765| D004850| CUTTER PIN| 1| |
189507| D005280| PISTON| 1| |
190009| D005730| MAIN FRAME| 1| |
190010| D005740| BOTTOM PLATE| 1| |
190011| D005870| THICKNESS| 1| |
190012| D005920| LOCKING STRAP PLATE| 1| |
| §| WEARING PART
---|---|---
| *****| PART THAT SHOULD BE STOCKED

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(17\)

BOSCH 0 607 951 449 –B900348 WELDING MOTOR

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(18\)

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(19\)

Item| Qty.| Part No.| Description| JDE

PART #

---|---|---|---|---
1| 1| 3 605 125 063| MOTOR HOUSING| x
2| 1| 3 604 090 009| STATOR / 550W| x
3| 1| 3 604 220 005| ROTOR| 189222
5| 1| 3 605 700 167| BEARING FLANGE| x
6| 1| 1 900 905 127| DEEP-GROOVE BALL BEARING / 6000-2Z/C3 DIN| x
7| 1| 3 605 700 010| BEARING FLANGE| x
8| 1| 1 900 905 127| DEEP-GROOVE BALL BEARING / DIN 625-608-2Z-C3| x
9| 1| 2 600 200 007| SPACER RING| x
10| 1| 3 600 202 004| SPACER RING| 190193
11| 1| 2 916 011 012| PLAIN WASHER / DIN 125-A5,3-ST| 190192
12| 1| 2 911 061 150| HEX SCREW / DIN 933-M5x8-8.8| x
26| 1| 3 606 337 209| CARRIER| x
40| 1| 3 600 390 040| FLANGE| 189697
55| 2| 3 600 100 048| SEALING DISC| 190003
61| 1| 3 603 462 017| SILENCER| 189272
66| 1| 3 604 710 032| STRAIGHT PIN| x
95| 1| 3 601 106 047| NAMEPLATE| x
99| 1| 3 601 119 236| REFERENCE PLATE| x
804| 1| 3 607 030 260| ASSEMBLY OF SERVICE PARTS / 5 PIECE| x

BOSCH 0 607 951 445 –B900353 TENSION MOTOR

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(20\)

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(21\)

SPARE PARTS LIST B900353

# QTY CODE DESCRIPTION JDE PART #
1 1 3 600 760 114 MOTOR HOUSING / BLUE 189730
2 1 3 604 090 003 STATOR / 370W
3 1 3 604 220 025 ROTOR 206631
5 1 3 605 700 005 BEARING FLANGE 189728
6 1 3 600 905 039 DEEP-GROOVE BALL BEARING / 9x24x7mm 190004
7 1 3 605 700 007 BEARING FLANGE
8 1 3 600 905 148 DEEP-GROOVE BALL BEARING / DIN 625-7x19x6 190005
9 1 2 600 202 013 SPACER RING
10 1 2 600 202 014 SPACER RING
11 1 2 916 011 012 PLAIN WASHER / DIN 125-A5,3-ST 190192
12 1 2 911 061 150 HEX SCREW / DIN 933-M5x8-8.8
14 3 3 606 316 000 CYLINDRICAL GEAR / Z=12 189990
15 6 3 600 913 000 NEEDLE-ROLLER ASSEMBLY / INA K3x5x7 189781
16 3 3 606 316 002 CYLINDRICAL GEAR / Z=18 207203
26 1 3 606 300 002 PINION / Z=23 206953
27 1 3 600 101 001 STOP DISC
28 1 3 606 334 000 RING GEAR / Z=49 207204
29 1 3 606 337 207 PLANETARY-GEAR CARRIER
33 6 3 603 201 000 NEEDLE ROLLER 205974
34 2 3 600 103 002 SHIM RING 206197
35 1 3 600 224 000 RETAINING RING
36 1 1 900 900 287 DEEP-GROOVE BALL BEARING / 6001 DIN 625 190184
38 1 3 606 337 206 PLANETARY-GEAR CARRIER
41 1 3 600 905 145 DEEP-GROOVE BALL BEARING
42 1 3 600 910 018 FREEWHEELING
43 1 1 900 210 113 O-RING / 15×2,5 mm
45 3 1 903 230 004 BALL / DIN 5401-3 MM-III-ST
46 1 3 603 344 056 THREADED RING 189696
56 1 3 605 190 190 VALVE HOUSING 189468
57 1 3 601 010 002 SILENCER 189729
62 1 3 603 458 019 FITTING 189660
65 1 3 600 210 036 O-RING / 16×1,25 mm 189663
66 1 3 604 710 051 STRAIGHT PIN
86 1 3 603 435 032 ADJUSTING SCREW 189652
87 1 3 600 210 015 O-RING / 4×1 mm 189648
90 1 3 600 105 002 SILENCER
95 1 3 601 106 047 NAMEPLATE
96 1 3 601 110 331 MANUFACTURER’S NAMEPLATE
99 1 3 601 119 236 REFERENCE PLATE
804 1 3 607 030 249 ASSEMBLY OF SERVICE PARTS 189626

B200357 PNEUMATIC VALVE

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(22\)

SPARE PARTS LIST B200357

#| ****

CODE

| ****

JDE PART #

| DESCRIPTION| QTY
---|---|---|---|---
1| SF 1/8| | SPRERE 1/8 AISI 420 grade B| 7
2| AZ00.112.2| | PISTON KIT DIAM. 12| 3
| AZ00.018.0| | LIP GASKET Oe12| 1
| AZ00.013| | PISTON DIAM.12| 1
3| AZ08.006.0| 189632| BUTTON SPRING| 2
4| AZ08. 007.N| | OR WITH MEMBRANE 02.6| 2
5| AZ08.008.0| 189304| GASKET HOLDER| 2
6| AZ08.010.1| | BUTTON| 1
7| AZ08.013.1| | BUTTON GUIDE| 2
8| AZ08.023.1| | BUTTON WITH HOLE| 1
9| AZ08.031.2| 189771| SPACER KIT WITH OR105+OR106| 2
| | | OR 105| 1
| | | OR 106| 1
| | | SPACER AZ08.004.0| 1
10| AZ1/82/M| | SHUTTER SH75| 2
11| AZ12.103.1| | GASKET HOLDER REG. 908| 1
12| AZ5.3.11| | OR NBR 70 5x3X11| 1
13| SF3/32| | SPRERE 3/32 AISI 420 grade B| 1
14| AZOO.021.0| | SINTERED| 1
15| SF 5/32| | SPHERE 5/32 AISI 420 grade B| 2
16| AZ00.001.0| | GASKET 1/8| 4
| AZ00.002.0| | SPACER 1/8| 3
17| AZ01.001.0| 189622| SPACER 1/4| 3
| AZ01.002.0| 189278| GASKET 1/4| 3
18| AZ00.010.0| | 3 WAY SHUTTLE 1/8| 4
19| AZ01.011.1| | 3 WAY SHUTTLE 1/4| 1
20| AZ00.046.0| | REDUCTON| 1
21| AZ00.407.0| | PIPI CARTRIDGE| 1
22| AZ01.013.0| 189621| GASKET HOLDER 017,4-1/4| 1
23| AZ01.013.0M| | GASKET HOLDER 017.4| 2
24| AZ00.008.0| | GASKET HOLDER 015,5-1/8| 1
25| AZ01.014.0| | GASKET HOLDER 0e20| 1
26| AZ01.047.0| 189712| SPRING| 2
27| AZ03.032.0| 189711| SHUTTER| 1
28| AZ10.017.0| | SHUTTER HOLE O0,5| 1
29| AZ11.001.0| | SHUTTER GUIDE| 1
30| AZ11.004.0| | SPRING| 1
31| AZ01.036.0| 189981| UNDERPISTON SPRING| 1
32| AZOR101| | OR101| 2
33| AZOR102| | OR 102| 1
34| AZOR110| | OR 110| 1
35| AZOR2010| | OR 2010| 1
36| AZOR2050| | OR 2050| 1
37| AZOR2081| | OR 2081| 2
38| SF 9/32| | SPRERE 9/32 AISI grade B| 1
39| AZ03.025.0| 189631| GUIDE SPRING| 1
40| AZ10.051.2| 190016| PISTON 020 WITH SUTTLE WITHOUT SCREW| 1
41| AZOR4X1| | OR4x1 PISTON 020| 2
42| AZ20.001.0| 189997| COOLING TIME STEM| 1
43| AZ20.000.0| 189994| PISTON 08| 1
44| AZ11.028.0| | GASKET HOLDER 08| 1
45| AZ20.002.0| 189996| CYLINDER BODY 08| 1
46| AZ20.004.0| 189999| SPRING| 1
47| AZ10.164.1| | BOTTOM PLATE| 1
48| AZ10.105.1| 204099| BODY VALVE| 1
49| AZ10.149.1| 206632| TOP PLATE| 1
50| AZOR106| | OR 106| 1
51| OR 2034| 189296| OR 2043| 1
52| OR 2043| 189296| OR 2043| 1
53| AZ12.002.1| | REGULATOR NIPPLE| 1
54| AZ10.175.0| | NEEDLE| 1
---|---|---|---|---
55| M4x12| | SCREW M4x20 UNI 5931 (BOTTOM VALVE)| 2
56| M4x20| 190015| SCREW M4x20 UNI 5931 (TOP VALVE)| 3
57| AZOR108| | OR 108| 1

CE DECLARATION OF CONFORMITY

Greenbridge declares under own responsibility that the under mentioned machinery, to which this declarations refers, is in conformity with 2006/42/CE Directive and successive modifications, as well as with standards EN12100-1 / EN12100-2.

GREENBRIDGE-PHT401-Pneumatic-Strapping-Tool-FIG-
\(23\)

MACHINE TYPE:
PNEUMATIC PLASTIC STRAPPING TOOL

GREENBRIDGE
6277 Heisley Road Mentor, Ohio 44060
Tel. 440-357-1500 Fax 440-352-9553 www.greenbridge.com
Manufactured in Italy

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GREENBRIDGE User Manuals

Related Manuals