GREENBRIDGE SP6119 Pneumatic Sealer for Steel Strap with Seal Joint User Manual

SP6119 / SP6132
OPERATION MANUAL | SPARE PARTS LIST
READ ALL INSTRUCTIONS BEFORE OPERATING THE TOOL
GREENBRIDGE
6277 HEISLEY ROAD, MENTOR, OHIO 44060
PHONE: 440.357.1500, FAX: 440.352.9553
WWW.GREENBRIDGE.COM
ED. 4/21

SAFETY INSTRUCTIONS

| READ THE OPERATING INSTRUCTIONS CAREFULLY
---|---
| WEAR EYE, FACE, AND HAND PROTECTION WHEN OPERATING THE TOOL.
| GENERAL SAFETY INSTRUCTIONS:

The tool must be used by properly trained people. Failure to follow the operating instructions or improper use could cause strap breakage, injuries, or package damages.
Check tool daily, do not use tool with worn or damaged parts. Use original spare parts for eplacement. Never modify any tool part.
Do not put fingers, hands or other body parts between the strap and package during the cycle.
It is your responsibility to check the seal joints made by your tool. Training about the weld time adjustment will be useful to check the seal quality in order to avoid severe injury. Never move goods with bad quality seals. Only use specific strap dispenser to dispense the strap. Keep your working area clean and always use the tool in good balance and safety conditions. Never use straps as a means of pulling or lifting goods.
Always use a proper safety strap cutter and keep other people and yourself at a safe distance from strap, always stand to side of strap, away from direction of strap trajectory once cut. Hold the upper strap portion and pay attention that the lower strap will snap forward away from you.
Improper operation, excessive tensioning, use of non-recommended strap, or sharp corners on the package could cause a loss of strap tension and/or strap breakage that could lead to packaging failure or injury. The following is recommended; use edge  rotectors if package has sharp corners, place the strap correctly around a properly positioned package, stand in safety position (on one side of strap) during strapping cycle, and use the correct strap quality, width, thickness, and break strength as recommended in this manual.
Please save this manual, as it is a part of the tool. This tool is manufactured without any substances which could be dangerous to health. National instructions must be observed for disposal of all the parts.

GENERAL SAFETY INSTRUCTIONS FOR COMPRESSED AIR:
Never operate this tool using bottled air or other gas source. Do not exceed the air pressure range as shown in this operation manual. For all adjustments, repairs or cleaning of the tool, always disconnect air supply. Always use dry, clean and lubricated compressed air.

TECHNICAL DATA

TOOL SIZE|
---|---
Length:| 12.6”
Width:| 5.5”
Height:| 7”
Weight:| 6.4lbs
AIR REQUIREMENTS|
---|---
Pressure Range:| 78-99 psi

CHART OF TYPES

0.025” – 0.031”
T453201| T453201| R 850N/mm2
R 1100N/mm2| 0.024” – 0.039”
0.025” – 0.031”

WARRANTY CONDITIONS AND LIABILITY

Greenbridge warrants all its tools and battery chargers during a period of 6 months from the shipping date document. Wear parts are warranted for 45 days, otherwise wear parts are excluded from regular warranty, wear parts are shown on spare parts list (in tool manual).
Warranty includes free replacement parts. The warranty is not valid in case of improper use, lack of maintenance, tampering, arbitrary modifications and reparations, use of non-original parts, disregard of instructions of the operation manual, or missing serial number. No compensation can be claimed for production shutdowns and for damages to people and objects due to tool defects. Greenbridge reserves the right to modify the tools and documentation without any obligation to update previous ones.
Greenbridge warrants all its batteries during a period of 120 days from the shipping date document. The manufacturer is committed to replace it with a free battery only when there are manufacturing defects that make it unfit for use.

INSTALLATION

It is recommended to always use a dryer unit near the compressor and a filter- regulator-lubricator unit with pressure gauge (part # 186895) close to the tool air connection to avoid water and dirt in the valves or in the pneumatic motors. Connect the tool to air with quick connector ¼” and use minimum 8mm or 3/8” internal diameter pipe; max length for flexible pipe 10 m between tool and regulator group. Check that your compressor / air distribution plant is able to supply the right air quantity as shown in the operation manual without losing pressure

TOOL AIR CONNECTION

OPERATING ELEMENTS AND ADJUSTMENTS

OPTION : The operator can change the position of the jaw to seal at 45° or 90°.
Disconnect the sealer from the air supply, then remove screws (part # 401-0141) (see the SPARE-PARTS LIST) .After removing the screws, turn the jaw to desired position and reinstall the screws.

OPERATION

Place the jaw of the sealer on top of the seal and pull the sealing lever (it’s possible to repeat this operation to make more than one notch on the same seal) (fig.C1). It’s important to check the depth of the notch in order to obtain a good seal joint (fig. C2).

TROUBLESHOOTING

PROBLEM
REMEDY
The notch of the seal is insufficient
Check if the strap and the seal are right for the pneumatic sealer.
Check the air pressure (min.78 psi) and check if the filter lubricator group is damaged or dirty.
Check if there are some broken or worn parts in the sealing group.
The tool has an air leak
The gaskets may need replacing (contact the after sale service).
Check the air fitting for tightness.
The sealing lever is locked and the sealing jaw is closed
The sealing lever spring may need replaced (contact the after sale service).

SPARE PARTS LIST

Ed. 06/17

GREENBRIDGE
PART #| ITEM| DESCRIPTION| QTY| |
---|---|---|---|---|---
189779| B100136| ALLUMINIUM GASKET 5/8′| 1| |
X| A005450| CYLINDER ASSEMBLED| 1| |
207994| A005480| FLANGE ASSEMBLED| 1| |
189780| B100305| REDUCER 3/8″-1/4″| 1| |
189672| B200104| BASE LANTERN CAMOZZI 458-3319 VALVE| 1| |
189674| B200105| MIDDLE LANTERN CAMOZZI 458-3319 VALVE| 3| |
189105| B200309| AIR FITTING 1/4″| 1| |
189673| B300085| GASKET OR 20×2| 4| |
189667| B300086| GASKET OR 108| 1| |
190129| B300156| GASKET OR2056| 1| |
189723| B300409| GASKET OR64501195| 1| |
189163| B500047| SCREW S.T.E.I. M5x8 UNI5925| 1| |
189782| B500098| LOCKNUT M8 DIN985| 1| |
189783| B500138| SCREW T.C.E.I. UNC 114×5/8″| 2| |
189784| B500146| LOCKNUT M10x1| 1| |
189736| B500164| SCREW T.S.E.I. M8x45 UNI5933| 2| |
189785| B500407| SCREW T.C.E.I. UNC 1/4×1/2″| 2| |
189786| B500408| SCREW T.B.E.I. M8x301507380| 1| |
189811| B500443| SCREW UNC1/4-20X3/4| 4| |
208132| B500449| SCREW M8X35 1507380| 1| |
189279| B600016| WASHER 010x16x1| 1| |
189693| B600118| INTERNAL SEEGER J20 DIN472 R150| 1| |
190052| B600159| SEEGER Al2 UNI7435 R150| 1| |
189722| B700171| CYL.ROLLER TMP. 08×10| 2| |
189787| B700182| CYL. PIN TMP 04×24 DIN6325| | |
189690| D000970| VALVE SPRING| 1| |
189788| D002460| SPACER 10mm| 1| |
190131| D004040| HANDLE| 1| |
190132| D004080| CYLINDER GASKET| 1| |
189789| D004100| PISTON| 1| |
189791| D004120| PISTON PIN| 1| |
189792| D004130| SEALER LINK 19mm| 2| |
189794| D004150| SEALER LINK 32mm| 2| |
189677| D004160| JAW| 2| §|
189795| D004180| LEVER| 1| |
189691| D004210| STEM VALVE| 1| |
189692| D004220| VALVE GUIDE| 1| |
189731| D004230| JAW ROTATION PIN| 2| |
189710| D004240| JAW PLATE 19mm| 2| |
189678| D004260| JAW PLATE 32mm| 2| |
189857| D004870| PISTON PIN| 1| |
189858| D004880| CYLINDER BASE| 1| |
189859| D004890| PROTECTION COVER| 2| |
§| WEARING PART
---|---
| PART THAT SHOULD BE STOCKED

CE DECLARATION OF CONFORMITY

Greenbridge declares under own responsibility that the under mentioned machinery, to which this declarations refers, is in conformity with 2006/42/CE Directive and successive modifications, as well as with standards EN12100-1 / EN12100-2

MACHINE TYPE: PNEUMATIC STEEL STRAPPING TOOL SEAL JOINT

GREENBRIDGE
6277 Heisley Road Mentor, Ohio 44060
Tel.440-357-1500 Fax 440-352-9553 www.greenbridge.com

References

• Greenbridge | Strapping Solutions, Tools & Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>