GREENBRIDGE B1200 Battery Powered Friction Weld Tool User Manual

GREENBRIDGE B1200 Battery Powered Friction Weld Tool

Product Information

• Product Name: B1200
• Manufacturer: GREENBRIDGE
• Address: 6277 Heisley Road, Mentor, Ohio 44060
• Phone: 440.357.1500
• Website: www.greenbridge.com
• Edition: 4/21

Dimensions

• Length:
• Width:
• Height:
• Weight with battery:

Feed Requirement

• Battery:

Performance

• Max. Tension:
• Tensioning Speed:
• Sealing:
• Joint Strength (approx.):
• Sound Emission Level:
• Vibrations at Handle:

Product Usage Instructions

1. Read all instructions before operating the tool.
2. Wear eye and hand safety protection and safety shoes when operating the tool.
3. The tool must be used by properly trained personnel.
4. Observe all laws when disposing of the tool and its parts, including the battery and charging unit.
5. Dismantle and separate the electrical parts from mechanical parts for proper disposal.
6. Collect, recycle, or dispose of the battery and charger in an environmentally friendly way.
7. If the tool displays a low battery signal in a low temperature environment, insert the battery into the charger for a refreshing for 2 minutes.

SAFETY INSTRUCTIONS

• READ THE OPERATING INSTRUCTIONS CAREFULLY

• WHEN OPERATING THE TOOL, WEAR EYE AND HAND SAFETY PROTECTION AND SAFETY SHOES

• GENERAL SAFETY INSTRUCTIONS

The tool must be used by properly trained personnel. Failure to follow the operating instructions or improper use could cause strap breakage, injuries, and package damage. Check the tool daily. Do not use the tool with worn or damaged parts; promptly replace them by trained personel only, using only original spare parts. Never modify any tool part. Do not put your fingers, hands or other body parts between the strap and package during the strapping cycle. It is your total responsibility to check the joints made by your tool. To avoid severe injury, properly train users on seal quality and adjustments prior to using the tool. Never move goods with bad quality seals. Use only specific strap dispenser to dispense the strap. Keep your working area clean and always use the tool in good balance and safety conditions. Never use straps as a means of pulling or lifting goods. To cut the straps always use proper safety strap cutters and keep other people and yourself at a safe distance from the strap, always stand to the side of the strap, away from the direction of the strap trajectory when cut. Hold the upper strap portion and pay attention to the lower strap. It will snap forward away from you. Improper operation, excessive tensioning, using non-recommended strap, and sharp corners on the package could cause a sudden loss of strap tension and/or strap breakage. This could lead to the package falling and cause violent movement of the strap against the operator. It is recommended to use edge protectors if package has sharp corners to place the strap correctly around a properly positioned package, to remain in safety position (on one side of strap) during strapping cycle, to use the correct strap quality, width, thickness, and strength as recommended in this manual. Please preserve this manual, it is as a part of the tool. This tool is manufactured without any materials which could be dangerous to health. Please observe all laws when disposing of this tool and all parts contained in it including the battery and charging unit.

DISPOSAL INFORMATION
Please observe all laws when disposing of this tool and all parts contained in it including the battery and charging unit. Please dismantle and separate the electrical parts from mechanical parts so they can be disposed of properly (separately). The battery and charger must be collected, recycled or disposed of in an environmentally friendly way as well.

TECHNICAL DATA

DIMENSIONS|
---|---
Length:| 300 mm – 11.8”
Width:| 150 mm – 5.9”
Height:| 160 mm – 6.3”
Weight with battery:| 4.1 kgs – 9 lbs
FEED REQUIR.|
---|---
Battery| 14.8V – 3.2 A/h LI- PO

PERFORMANCES|
---|---
Max.Tension :| 1200 lbs
Tensioning speed:| 12 mt/m

Sealing:

| Friction weld seal Soudage a friction
Joint strength approx.:| *80% plastic strap strength

Level sound emission.
Measurement type A (2003/10/CE)| 81 dB (A)
Vibrations at handle (2002/44/CE)| 2.2 ms 2**

• depends on strap quality
  Working temperature: The tool should be used between 0C° (32F) and +45C° (+113 F). When used in a low temperature environment the tool may display a low battery signal. In this case insert the battery into the charger for a “refreshing” for 2 minutes.

CHART OF TYPES

(0.031” ÷ 0.041”)
0.7 mm ÷ 1.30 mm (0.027” ÷ 0.050”)

Warranty and condition

Greenbridge warrants all its tools and battery chargers during a period of 6 months from the shipping date document. Wear parts are warranted for 45 days, otherwise wear parts are excluded from regular warranty, wear parts are shown on spare parts list (in tool manual).
Warranty includes free replacement parts. The warranty is not valid in case of improper use, lack of maintenance, tampering, arbitrary modifications and reparations, use of non-original parts, disregard of instructions of the operation manual, or missing serial number. No compensation can be claimed for production shutdowns and for damages to people and objects due to tool defects. Greenbridge reserves the right to modify the tools and documentation without any obligation to update previous ones.
Greenbridge warrants all its batteries during a period of 120 days from the shipping date document. The manufacturer is committed to replace it with a free battery only when there are manufacturing defects that make it unfit for use.

INSTALLATION

BATTERY

SAFETY INSTRUCTIONS: To begin operating the B1200, remove the spacer and insert the battery until the locking button clicks into position. The battery is designed for use in the B1200 strapping tool and to be recharged only by the provided battery charger. For other purposes or applications our warranty and liability is not valid. The battery should be used by properly trained personnel. Failure to follow the operating instructions or improper use could result in injuries and battery damage. The battery is supplied partially charged. The lithium polymer rechargeable battery can be charged at any time without reducing its service life. Interupting the charging procedure does not damage it. To use and charge the battery, please follow the battery charger instructions. Check battery daily; do not use it with worn or damaged parts. Do not disassemble it, never modify any part, do not connect the positive (+) and negative (-) terminals. This can result in battery damage or a short circuit. Do not invert the right polarity during the use or charge. Do not transport or store the battery with metal objects, this can result in a short circuit. Do not try to charge with different charger, the battery could be seriously damaged. Do not put metal keys or other objects between contacts. Do not use the battery for purposes other than those specified. Battery must not be left in charging mode without supervision. Do not discharge the battery to less than 10.8V, it could be damaged. Do not throw the battery into a fire or heat it, do not store at high temperature or direct sunlight, do not put the battery in a microwave oven or a pressure cooker. Keep it away from any exposed flame. Do not dip the battery in water, protect it from humidity. Do not subject the battery to impact; do not throw it, drop it, or drill it. In case of heat generation, smoke emission, or ignition stop use immediately and replace it. In case the electrolyte comes into contact with eyes, rinse eyes thoroughly with clean water immediately and consult a physician; for contact with hands wash hands with clean water.

TECHNICAL DATA:

• Li-Po (Lithium-Polymer) 14.8V – 3.2 Ah
• Weight: 1.25lbs. Cod. (B1200BAT) Charging time approximately 40 min.
• Temperature charging and discharging: 0C° ( 32F) and +45C° (+113 F)

BATTERY CHARGER
SAFETY INSTRUCTIONS: The charger must be used only to charge the B600/B1200 lithium polymer battery. If used for other purposes or applications our warranty and liability is void. The charger should be used by properly trained personnel. Failure to follow the operating instructions or improper use could cause injuries and battery damage. To use the battery please follow the B1200 operating instructions. Check charger and main supply cable daily; do not use it with worn or damaged parts. Do not disassemble it, never modify any part, do not connect the contacts which can result in battery damage or short circuit. Do not invert the polarity during use or charge. Do not put metal keys between contacts. Do not use for purposes other than those specified.

BATTERY MUST NOT BE LEFT IN CHARGING MODE WITHOUT SUPERVISION.
Do not store at high temperature or direct sunlight, do not cover fan clefts. Do not dip it in water, protect it from humidity. Do not subject it to impact; do not throw, drop or drill it, if any of these conditions occur test it with care. In case of heat generation, smoke emission, or ignition stop use immediately and replace it. Place the charger on flat, not flammable and heat resistant surface. Keep away from any volatile or flammable substances. Disconnect from main power supply when is not used, to get service and maintenance use only authorized dealers.

CHARGING PROCEDURE: Before connecting to main power supply please check that the voltage value is correct (see label) this charger is autos witching. Stand-by green LED lights.
Put the battery into the charger correctly (do not invert the polarity), charging will start automatically. An acoustic signal is emitted and the LED becomes RED (see “LIGHT SIGNALS” and “ACOUSTIC SIGNALS”). It will remain in this condition up to 80% of charging, when the LED starts blinking GREEN, the charging process is from 80% to 99% complete. The charging cycle is complete when the Green blinking LED stays GREEN and the acoustic signal is emitted at the end of charging. Remove the battery from charger.

FAILURE: A blinking RED LED signifies the temperature of the battery is not compatible with the recharging process or its voltage is lower than 10.4V and therefore recharging will not occur. This condition is also used to indicate other possible issues, such as defective battery, dirty contacts etc. Check and wait for the battery to return to normal temperature; if recharging does not occur, contact the service center.

TECHNICAL DATA:
Cod.600CHG

• Input: 90V – 230V – 50/60Hz – 80W
• Output: 16.8V – 4.7A

ATTENTION: The battery charger is to be used only with the Li-Po 14.8V battery

VISUAL SIGNAL

SOUND SIGNAL

DOUBLE SHORT BEEPS EVERY ONE MINUTE AFTER

FULL CHARGE REACHED

| BATTERY FULLY CHARGED – READY TO USE

BUT STILL HOUSED INTO CHARGER

FAST INTERMITTENT CONTINUOUS BEEPS| BATTERY HAS TROUBLE – BATTERY DID NOT CHARGE

ACCESSORIES
The tool can be equipped with a stainless steel wear plate to protect the base against excessive wear when used on abrasive surfaces like bricks, concrete, stones, etc … Order item number: 401-6057

SUSPENSION HOOK
The tool can be equipped with a three position suspension hook. The hook must be fixed to the tool by two screws (included) in vertical or horizontal position. Order item number: 401-6058

OPERATING ELEMENTS AND ADJUSTMENTS

DO NOT OPERATE THE TOOL WITHOUT STRAP, YOU COULD DAMAGE THE FEEDWHEEL AND THE WELDING / CUTTING GROUP

LED SIGNALS

GREEN| TOOL READY FOR WORK
GREEN BLINKING| STAND-BY TOOL

ADJUSTING TENSION AND WELDING
In order to adjust (welding and tensioning), the tool must be switched on. Then press the adjust tension button as shown in picture A for about 3 sec., a number equal to the tension force will flash and you can select the desired value. Once you release the button, the number will stop flashing after about 3 seconds and the set value will be stored. The same procedure must be done in order to set the welding value using the button as shown in picture B.

OPERATING MODE
Press and hold the SET button for 3 seconds to access the various modes of operation (automatic, semiautomatic and manual) Fig C. The display will flash the LED corresponding to the mode in use, then you can select the one you want, when you release the button, the LED will stop blinking after about 3 seconds and the mode you selected will be stored.

AUTOMATIC STRAPPING: To activate the automatic strapping cycle quickly press button number 1 twice. Tension, seal, and cut off occur automatically. To STOP the automatic cycle press buttons 1 or 2.
Warning: after 15 seconds tension is automatically stopped if the tension setting has not been reached

SEMI-AUTOMATIC STRAPPING: To activate this cycle hold down button number 1 until set tension is reached. The tool will then automatically seal and cut off. If button number 1 is released before set tension is achieved tension will stop. Button number 1 can be pressed again and when set tension is reached tool will automatically seal and cut off.

STRAPPING MANUAL: To activate this cycle press button number 1 until desired strap tension is reached then press button number 2 for seal and cut off.

WELDING AREA ADJUSTMENT
Using various width strap can result in a non uniform weld. This situation can be corrected by adjusting screws as shown in pictures D-1 and D-2.
If the weld appears mostly on the outside edge of the seal (pic. D-3) slightly loosen the outside set screw and if needed slightly tighten the inside set screw for a uniform weld (pic.D4)
If the weld appears mostly on the inside edge of the seal (pic.D5) slightly loosen the inside set screw and if needed slightly tighten the outside set screw for a uniform weld (pic.D6)

STRAP SIZE CONVERSION
The B1200 is adjustable for either 5/8” (16mm) or 3/4” (19mm) width strap sizes by replacing the front and side strap guides with the proper strap width guide and moving the rear strap guide pin as shown in the picture below.

OPERATION

The tool model B1200 is designed to strap packages with plastic strap. The strap is fed around the package manually and inserted in the tool, as shown in the instructions, tensioned, friction welded and cut off by the tool. Wrap the package to be strapped, as shown in pic.E1, holding the tip of the strap with left hand and bringing the top strap over the bottom strap ( make sure that the strap is clean and free from oil and grease ); to open the tool squeeze the lever release, insert straps keeping them aligned by pushing them against the front and rear strap guides. Pressing tension button number 1 will activate tension to the preset tension as shown in (fig. E2). (once the maximum set tension is reached, the tool allows the operator to carry out 3 additional tension presses after which welding must take place. In order to carry out welding process press button 2, the tool will seal and cut and allow for cooling of the seal (fig. E3). The LED and the sound of the tool will indicate the end of the welding cycle. The tool may now be removed from the strap (fig. E4).

CONTROL BATTERY LEVEL : During use of the tool, it is important to view the charge status of the battery. Battery charged (fig.E5) – battery charge half (fig.E6) – Low Battery (fig.E7). When the battery is about to run out of charge, the LED will flash.

SEAL CHECK
A regular seal quality control check is very important and seals should be examined visually as follows:

SERVICING – CLEANING

Clean the tool periodically to remove strap dust, particularly the feed wheel, the gripper plates and the cutter. Only use compressed air for cleaning. Do not use a hard object to remove strap dust as you may damage the feed wheel.

CLEANING AND REPLACING FEEDWHEEL

To replace or clean the feedwheel FIRST remove the battery from the tool. Remove 4 socket head cap screws 401-2012, remove the cover by turning it slightly, then remove the feedwheel from the gearbox and the ball bearing 401-2007 from the feedwheel. To clean the tension roller use compressed air. Check the wear of the teeth before reinstalling it, if teeth are worn replace it with a new one. To replace, reassemble in reverse order.

CLEANING AND REPLACING STRAP
To clean or replace the strap locker proceed as follows: FIRST Remove the battery from the tool, remove the 2 screws 401-2027 and remove the 2 washers 401-2134. Remove the strap locker from the front using needle nose pliers. For cleaning of the plate use compressed air. Check the wear of the teeth , if teeth are worn replace it with a new one. To replace, reassemble in reverse order.

WELDING FOOT AND WELDING PLATE REPLACEMENT
To replace the welding foot and the welding plate proceed as follows:FIRST remove the battery from the tool. Remove the cover screw, remove the pin 401-2066, remove welding foot 401-2109 with the help of a clamp and replace. To replace the welding plate repeat the previous steps, then through the socket of the welding foot remove screw 401-2108, slide out with the help of a pair of pliers welding plate 401-2109. To replace, reassemble in reverse order

CUTTER REPLACEMENT
To replace the cutter proceed as follows :FIRST Remove the battery from the tool. Remove the cover screw, remove the screw 401-2012, remove the cutter guide 401-2076 and finally remove the cutter and replace it with a new one. Reassemble in reverse order.

SERVO CONTROL RESET
Should a problem occur during the welding operation, the foot may remain in the down position and prevent removal of the tool. If this situation occurs, remove and reinsert the battery. The servo will return to original position.

TROUBLESHOOTING

The tool doesn’t work after the battery is installed

• Check the battery contacts in the rear tool battery compartment and / or if there are disconnected wires
• Check the battery charge status

The strap tension is too loose

• Check the tension setting on keypad
• Check if the tension motor is damaged or worn out
• Check the gearbox
• Check the electronic card

The feed wheel slips on the strap

• Check if the feed wheel or grippers need cleaning or are damaged. Clean or replace as needed. Adjust the tension.
• Check if the strap qualities are right for the strapping tool and application

The strap is breaking during tension

• Adjust the tension force. Check if the strap qualities are right for the strapping tool and application. Check the package for sharp edges.

The seal is not aligned

• Adjust the tension power. Check if the strap qualities are right for the strapping tool and application. Check strap size, adjust the guides. Check the alignment guides.

The tool goes forward during the tension

• Check if the gripper is dirty or damaged. Adjust the tension.

The sealing isn’t enough; the upper strap isn’t completely cut; the cutting isn’t consist ant

• Check the sealing time, it may be too short, increase sealing time.
• Check if the sealing foot and / or the cutter are damaged or worn out Check if the sealing foot is dirty or worn
• Check if the tool comes back after tensioning
• Check the battery charge
• Check if the strap qualities are right for the strapping tool and application
• Check if the sealing motor is worn out Check the electronic cards

During the sealing both straps are cut

• Check if the gripper plate (under the sealing foot) is dirty or damaged (clean or replace it)
• Check if the tension setting is too high for the strap in use. Improper weld timing adjustment. Weld time may be too long, reset weld time.

Pressing the welding button doesn’t start the motor

• Check if the welding button is damaged or disconnected.
• Check if the sealing motor is worn out and the cables are connected
• Check the electronic cards

It is difficult to adjust the work parameters or they don’t remain constant or won’t change on keyboard

• Possible keyboard or electronic card problems / try to replace them.

Progressive problems with the battery life.

• Check the battery charge, try to recharge and check if the battery charger is running well.
• May be that the battery is near the recharge life limit
• May be that the internal cells are damaged due to strong impacts, or worn out.
• Test tool with a different battery

The charger will not start to recharge the battery

• The battery is damaged. The battery voltage is lower than 10V – check with electric tester Check if the charger is still running

SPARE PARTS LIST

Ed. 10-20

| GREENBRIDGE PART #| CODE| Description| qty| |
---|---|---|---|---|---|---
| B1200BAT| A000175| 3.2Ah Li-Po BATTERY| 1| §|
| 190260| A000177| TENSION MOTOR ASSEMBLED| 1| |
| 190212| A000179| CONNECTING ROD ASSEMBLED| 1| |
| 190202| A000180| WELDING MOTOR ASSEMBLED| 1| |
| 190213| A000181| ECCENTRIC SHAFT ASSEMBLED| 1| |
| 190261| A000182| TENSION MOTOR FLANGE ASSEMBLED| 1| |
| 190215| A000184| SUPPORT FEEDWHEEL ASSEMBLED| 1| |
| 190216| A000185| SERVO/CAM CONNECTING LEVER| 1| |
| 190137| A004650| WELDING FOOT SUPPORT ASSEMBLED| 1| |
| 190231| A800511| LEVER+DRIVE ASSEMBLED| 1| |
| 190026| B400186| BEARING 61808-ZZ C3| 1| |
| 190028| B400188| BEARING INA HF0812| 1| |
| 190029| B400332| BEARING 609-ZZ| 1| |
| 190030| B400333| BEARING 61902-ZZ| 1| |
| 190218| B400480| ROLL BEARING HK1214| 1| |
| 190217| B400520| SERVO BEARING H61700-2Z| 1| |
| 190031| B500035| CYLINDER SCREW M4x10 UNI5931| 6| |
| 190196| B500037| CYLINDER SCREW M4x8 UNI5931| 4| |
| 189136| B500039| SCREW UNI 10-24×1/2”| 2| |
| 189155| B500041| SCREW M4X30 UNI5931| 1| |
| 189698| B500047| SCREW M5x8 UNI 5925| 1| |
| 190219| B500049| SCREW M4x6 DIN7984| 2| |
| 190161| B500068| CYLINDER SCREW M3x8 UNI5931| 12| |
| 190037| B500158| CYLINDER SCREW M4x12 UNI5931| 1| |
| 190147| B500211| WASHER| 6| |
| 190040| B500273| CYLINDER SCREW M3X10 UNI5931| 1| |
| 190042| B500281| NUT M6 DIN985| 1| |
| 190043| B500336| SCREW M4x10 UNI5933| 6| |
| 190044| B500379| SCRW M4X5 UNI5923| 1| |
| 190047| B500395| SCREW BOSSARD BN13577 3.5×16 KA35| 9| |
| 190033| B500418| SCREW UNC10-24X3/8| 2| |
| 190220| B500464| SCHNORR WASHER R150 DIAM.3| 6| |
| 190221| B500465| CYLINDER SCREW M5x14 UNI5931| 4| |
| 190222| B500519| SCREW BOSSARD BN13577 3×30| 2| |
| 190223| B500522| SCREW BOSSARD BN13577 3.5×35 KA35| 1| |
| 190225| B500524| VITE TBEI M5x8 ISO7380| 1| |
| 190226| B500529| SCREW 3×20 DIN7505 A| 4| |
| 404919| B500548| SCREW M4X8 UNI5923| 4| |
| 404902| B500559| SCREW M3X5| 9| |
| 190050| B600112| WASHER PS12X18X0.5 DIN988| 1| |
| 190053| B600189| CIRCLIP D3.2| 1| |
| 190054| B600190| CIRCLIP D8 TYPE E DIN 471| 1| |
| 190134| B600227| CUP WASHER CB12.5X6.2X0.7 D.2093| 1| |
| 190057| B600343| SPRING G13-025 ISO10243| 1| |
| 190060| B600346| CIRCLIP D15 UNI 7435 R150| 1| |
| 190227| B600402| CIRCLIP RA4 UNI7434 R150| 1| |
| 206908| B600468| WIRE CLAMP| 1| |
| 190062| B700076| PIN Ø4×12| 1| |
| 190064| B700325| SPHERE DIAM. 5mm| 8| |
| 190228| B700260| SPINA CIL. Ø5×30| 1| |
| 190229| B700525| PIN 6X20 UNI6364B| 2| |
| 190230| B800510| TENSION/WELDING BUTTON| 2| |
| 190205| B800515| KEYBOARD| 1| |
| 190204| B800531| ELECTRONIC SIGNALS CARD| 1| |
| 190263| B800533| POWER CARD| 1| |
| 190232| B800534| POWER CARD–KEYBOARD CONNECTION CABLE| 1| |
| 190070| D000010| CONNECTING ROD PIN| 1| |
| 190071| D000170| GEAR SHAFT| 1| |
| 190072| D000200| 16mm FRONT STRAP GUIDE| 1| |
| 190073| D000250| STRAPLOCKER| 1| §|
| 190074| D000330| FREEWHEEL SUPPORT| 1| |
| 190076| D000390| WASHER| 1| |
| 190077| D000400| FREE GEAR| 1| |
| 190079| D001140| OPENING LEVER SPRING| 1| |
| 190081| D002020| WELDING FOOT PIN| 1| |
| 190087| D002080| PIN| 1| |
| 190091| D002130| CUTTER GUIDE| 1| |
| 190092| D002140| COVER| 1| |
| 190098| D002240| SPRING PIN| 1| |
| 190101| D002270| ROLLER| 1| |
| 190110| D002990| BLADE SPRING| 1| |
| 190123| D004540| WELDING FOOT| 1| §|
| 190145| D004560| SPECIAL SCREW| 1| |
| 190124| D004600| WELDING PLATE| 1| §|
| 190126| D004620| CUTTER| 1| §|
| 190136| D004630| FRONT STRAP GUIDE 19mm| 1| |
| 190179| D005550| GEARBOX| 1| |
| 190206| D006030| SPRING| 1| |
| 190263| D006040| LEVER/HOOK SUPPORT| 1| |
| 190264| D006050| FEEDWHEEL| 1| §|
| 190265| D006060| WELDING FRAME| 1| |
| 190266| D006090| SUPPORT| 1| |
| 190208| D006120| ANTIWEAR PAD| 1| §|
| 190234| D006130| WELDING MOTOR FLANGE| 1| |
| 190235| D006140| SPRING PIN| 1| |
| 190236| D006160| SPRING SUPPORT| 1| |
| 190237| D006180| LATERAL STRAP GUIDE 16mm| 1| |
| 190267| D006190| LATERAL STRAP GUIDE 19mm| 1| |
| 190238| D006200| PIN CAM| 1| |
| 190239| D006210| CAM| 1| |
| 190240| D006250| SERVO SUPPORT| 1| |
| 190242| D006270| PIN| 2| |
| 190243| D006280| REAR STRAPGUIDE| 1| |
| 190245| D006300| MAIN FRAME| 1| |
| 190246| D006320| CENTRAL PIN| 1| |
| 190248| D006350| HOOK| 1| |
| 190251| D006410| OPENING LEVER| 1| |
| 190252| D006420| TOP PLASTIC TOOL COVER| 1| |
| 190253| D006430| BOTTOM PLASTIC TOOL COVER| 1| |
| 190254| D006440| BLADE COVER| 1| |
| 190255| D006450| HANDLE| 1| |
| 190256| D006460| BATTERY CARD PLASTIC FRAME| 1| |
| 190209| D006510| REAR STRAP GUIDE PIN| 1| |
| 204059| D006570| STRAP GUIDE SPRING| 1| |
| 206283| D007030| SPECIAL SCREW| 2| |
| 404920| D009990| DRIVE LEVER| 1| |
| §| WEARING PART| |
| *****| PART THAT SHOULD BE STOCKED|

CE DECLARATION OF CONFORMITY

GREENBRIDGE declares under own responsibility that the tool B1200, to which this declarations refer, is in conformity with 2006/42/CE Directive and successive modifications, as well as with standards EN12100-1, EN12100-2, EN60745-1, EN60745-2-18, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3

MACHINE TYPE:
BATTERY POWERED PLASTIC STRAPPING TOOL

GREENBRIDGE
6277 Heisley Road Mentor, Ohio 44060
Tel. 440-357-1500 Fax 440-352-9553 www.greenbridge.com

References

• Greenbridge | Strapping Solutions, Tools & Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>