GREENBRIDGE PC1000 Automatic Strapping Machine Instruction Manual

GREENBRIDGE PC1000 Automatic Strapping Machine

Product Information

Specifications

• Model: PC1000
• Manufacturer: Greenbridge
• Address: 6277 Heisley Road, Mentor, Ohio 44060
• Contact: Phone – 440.357.1500, Fax – 440.352.9553

Product Usage Instructions

Part I – General Safety Instructions

Before operating the strapping machine, ensure you have read the operation and safety manual provided with the product. The manual should always be kept attached to the machine for reference.

Only trained personnel should operate the machine. Regular inspections and maintenance are crucial for safe operation. Refer to the Maintenance section in the manual for guidance.

Ensure all safety devices are in place and functioning correctly before operating the machine. Do not bypass or alter safety mechanisms.

When moving the machine, always disconnect it from the power supply. Reconnect the power properly before resuming operation.

Part II – Wiring Diagram

Refer to the wiring diagram provided in Section B1 for understanding the electrical connections of the machine.

Part III – Components Overview

• Strapping Head Unit (Section C1)
• Bandway Unit (Section C43)
• Accumulator Unit (Section C63)
• Reel Control Group (Section C85)
• Body Frame Unit (Section C95)
• Electric Control Unit (Section C133)

FAQs

• Q: Who should operate the strapping machine?
  • A: Only trained personnel should operate the machine to ensure safety and proper functioning.
• Q: What precautions should be taken before using the machine?
  • A: Before operating, ensure all safety devices are intact, conduct regular maintenance checks, and refer to the operation manual for guidelines.
• Q: How should the machine be moved?
  • A: When relocating the machine, always disconnect it from the power supply. Reconnect the power properly before using it again.

General Safety Instructions

1.1 Basic Operation
Read the operation and safety manual prior to using the strapping machine. The operation and safety manual should remain attached to the machine at all times. The machine may only be operated in accordance with its designated use. The strapping machine was built in accordance with state-of-the-art standards and
recognized safety rules. Nevertheless, improper use can still result in injury to personnel or damage to the machine and other material property.
Machine shall only be operated by trained personnel. Perform inspections and maintenance at regular intervals. Refer to the Maintenance
section of the manual. The machine may not be put in operation before checking the respective devices. Safety devices must never be bridged or eliminated by any means. To transport the equipment only use lifting apparatus and loading devices with sufficient
capacity. Always disconnect from external power supply when changing the location of the
machine, even if the location should only be slightly changed. Connect power supply properly before returning to service. Do not alter or bypass protective interlocks. Do not alter circuits and machine unless authorized to do so by the manufacturer.
1.2 Basic Safety Precautions
In addition to the instructions for operation, the user is to be instructed in all generally applicable legal or mandatory regulations relevant to safety or the environment.
Long hair, loose-fitting garments, or jewelry can be a safety hazard. These items must be secured prior to equipment operation.
Use protective equipment whenever appropriate or when required by law. Carefully observe all safety instructions and warnings attached to the machine. Keep
safety labels clean and legible. People that are being trained to operate or service the equipment must be supervised by
experienced personnel. Any electrical work performed on the equipment must be conducted by a skilled
electrician or under the supervision of a skilled electrician. All work must be observed good electrical engineering practice and follow safety rules and local wiring standards.
-A1-

1.3 Safety Instructions Governing Specific Operational Phases
Avoid unsafe operation of the equipment. The machine is only to be operated when it is in good running order. Only operate the
equipment in a safe manner; all protective and safety devices must be in place and fully functional. This includes removable safety devices, emergency shut- off equipment, noise-protection devices and exhaust fans. The machine is to be checked for damage and defects at least once each work shift. Any changes, including the working behavior of the machine, are to be reported immediately. If necessary, the machine is to be stopped and locked-out immediately. In case of a malfunction, the strapping machine is to be immediately stopped and locked-out until the fault has been eliminated. Before starting the strapping machine, make sure that the area is clear and safe. Do not place any tools or parts onto the machine. Operating personnel needs to be well trained before executing special operations and maintenance work; this work needs to be done with the proper supervision. Always check and tighten connections after maintenance or repair. After completing maintenance or repair, all safety devices must be replaced and checked for functionality before operating the equipment. To minimize the environmental impact, all consumables and replaced parts must be disposed of safely. Before starting the machine, check that the accessories have been stowed away safely. Avoid operating the machine in a fashion that could upset its stability.
-A2-

1.4 Warning of Electrical Dangers
Immediately remove power to the machine in case of trouble in the electrical system. Replace a fuse with one with the same style and ratings; pay particular attention to matching the specified current.
Any electrical work performed on the equipment must be conducted by a skilled electrician or under the supervision of a skilled electrician. All work must be observed good electrical engineering practice and follow safety rules and local wiring standards.
Inspect the electrical equipment of the machine at regular intervals. Tighten any loose connections. Check wiring for scorch marks; replace scorched wiring and determine and correct the reason for the overheating.
When working on live equipment, ensure that a second person is available to cut power in case of an emergency. When appropriate, secure the working area with safety tape and a warning sign. Use insulated tools for electrical work.
Before working on high-voltage assemblies, turn off the power supply. Carefully discharge the supply cable and short-circuit any energy-storage components such as capacitors.
If the equipment was moved, carefully refit and refasten all parts removed for transport before reapplying power.
Before moving the machine, remember to disconnect the power cable.
1.5 Grounding Instructions Shall Include the Following
This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock. This product is equipped with a cord that has a grounding wire and an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
If repair or replacement of the cord or plug is necessary, connect the ground wire to the ground terminal of the plug. The wire with green insulation (with or without yellow stripes) is the grounding wire.
Check with a qualified electrician or service person if the grounding instructions are not clear or if in doubt about the proper grounding of the machine. Do not modify the plug provided; if it will not fit the power outlet, have the proper outlet installed by a qualified electrician.
DANGER!
Improper installation of the grounding can result in electrocution.
-A3-

1.6 Before Operating
Read the instruction manual before operating the machine for your safety. Wear eye protection and safety gloves before operating this machine.

Eye protection must be worn

Safety gloves must be worn

Verify that the power line voltage is correct. The machine must be properly grounded to avoid a shock hazard. All wiring must be
in accordance with local wiring standards. The strapping machine can only be operated with polypropylene (PP) strapping;
do not use polyester (PET) strapping or polyethylene (PE) cord strap.

1.7 During Operation
The weight of the package cannot exceed 40kg (88 lbs), but it may be necessary to use lifting aids for handling products that exceed 25kg (55 lbs).
The size of the package should not be less than 70 mm × 20 mm (2.75 inches × 0.75 inches).
While running, check the unit for any unusual sounds or smoke emissions. Keep away from the inside of the arch while the machine is operating; do not put your
hands or body into the arch when the machine is running.
NOTE: it is normal for the heater tongue to smoke during the sealing operation.

1.8 After Operating
Remove dust and dirt from the unit; pay particular attention to the interior of the arch. Turn off the power when the machine is not in use.

-A4-

1.9 Signs and Symbols
Symbol

Meaning
Warning for dangerous voltage! Contact with live electrical parts will result in severe injury or death.
Warning for hot surface! Welding area is approximately 270oC(520oF) Allow sufficient time for the heater to cool down before any work in welding area.
Warning for danger! Do not put your hands or body into arch working area when machine is operating.

-A5-

Machine Information

2.1 Areas of Application
The strapping machine is to be used for strapping packages, cartons, paper boxes, newspapers, magazines and those materials using a polypropylene (PP) strapping for stabilizing purposes when in transportation. Be careful for rigidity of working materials, and dont try to pack agri-foodstuffs or other such material.
This machine was designed for certain applications only. We strongly recommend that this machine NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the machine until you have had detail instruction from your dealer.
2.2 Environment Information
The strapping machine shall be installed in the following conditions:
Supply voltage: 0.9 – 1.1 nominal supply voltage Source frequency: 0.99 – 1.01 nominal frequency Ambient temperature: 5°C – 40°C (41-104). Altitude: shall be at altitudes up to 1000m above mean sea level. Relative humidity: not exceed 50% at 40°C. Atmosphere: Free from excessive dust, acid fume, corrosive gases and salt. Avoid exposing to abnormal vibration. Don’t use machine in dangerous environment. Don’t use machines in damp or wet locations, or expose them to rain. Please provide a suitable illumination around the machine for safety operation. Work place of user should have a fire extinguisher or other devices that meet their local
safety regulations, and always be careful. Internal parts requiring frequent inspection and adjustment, and maintenance areas must
be provided with a suitable illumination around the machine.
If there may be harmful gases, fumes or dust generated during heating, user or system integrator must install exhaust system for the extraction of harmful substances.
The exhaust system shall be positioned according to the vent location. Please refer to the figure.
-A6-

And the user should refer to a professional expert or relevant authority to prevent the dangerous substance/ gas emitted by suitable means according to local /national environmental/health codes/regulations.
2.3 Storage
The store room must be dry Do not expose the machine to extreme cold or heat environment Place the machine on an even floor in order to avoid any distortion
2.4 Machine Description
Automatic strapping machine for polypropylene (PP) strapping material. Strap width 12mm. Electronic heater temperature control. Hinged front table. Automatic strap loop ejection in case of strapping cycle without package. Extra tough construction. Simple, safe and user-friendly operation. Automatic strap feeding system. Automatic strap end detection. Mobile, with large table area and high capacity strap reel Table surface made of stainless steel. Strap tension adjustable from soft to extremely high.
-A7-

2.5 Safety Devices
Danger!
Operate the machine only when all safety devices are at their place and are functioning correctly.
The machine has been constructed in accordance with the applicable legal regulations. The machine is reliable in operation. Nevertheless the machine may constitute a danger if it is operated in improper or undue condition. Danger points that cannot be avoided due to equipment design are equipped with safety devices. If necessary, these points are marked on the machine with warning signs, and in the manual under working safety instructions.
The machine is equipped with the following safety devices: 1. Warning signs at the danger points of the machine 2. Automatic shunt down of machine when front table opening 3. Live parts are secured by cover
-A8-

If it is necessary to make adjustments inside the machine during operation, after a strap jam for example, the rear table top can be unscrewed. Observe caution as the machine is still fully functional with the covers removed. When the front table top is opened, safety switch B6-1 is activated. This will remove power but the heating element will keeping heating.
CAUTION!
The heating unit operates at a very high temperature in order to melt the PP strapping. To prevent burns, avoid contact with this area.

2.6 Technical Specification

2.6.1 Electrical Specification

System configuration: Nominal power: Rated current: Rated voltage: Rated frequency: Type of current

1L+N+PE (Ground) 0.5kW 3A
220V/230V/240V 50Hz
AC – single phase
-A9-

1L+N+PE (Ground) 0.5kW 5A 110V 60Hz
AC – single phase

2.6.2 Technical Data

Strap width Strap thickness
Strap coil diameter
Table height Weight Noise emission Ambient temp Minimum package size:
Maximum package size:

12mm 0.45mm up to 0.65mm (0.017″ ­ 0.026″) Coil diameter 200mm (8″ nominal) Outside diameter 420mm (16.5″) Width(Face) 190mm (7.5″)
Minimum ­ 820mm (32.3″) Maximum ­ 920mm (36.2″) 167 kg (368 lbs) 78 dBA 5 – 40 (41 – 104) 70mm W × 20mm H (2.75″ W × 0.75″ H)
arch size minus 50mm (1.97″) EX: arch size: 650W×500H Max. package size: 600mm W×450mm H
(23.6″ W × 17.7″ H)

-A10-

Preparation Before Operating the Machine

3.1 Shipping
The equipment is delivered in transport units. Each transport unit is loaded onto a wooden pallet, secured by polyester strapping.

3.2 Transportation & Centre of Gravity
Transport the strapping machine on a pallet. Lift the unit using forklift truck or other lifting device. Proper packaging requires that the casters rest in a recess. Cover the machine with a sturdy box for protection. Secure the unit to the pallet with plastic strapping. Place the strapping across the top plates. Use cardboard to avoid marring. Use plastic strapping to hold the cover to the pallet.
The machine can be removed from the pallet using forklift truck or other lifting device.

CAUTION!
Do not carry machine by having the forklift’s fork under the arch, but only under the machine frame.

Center-of-gravity position

-A11-

Danger to Lift! Suspend loads can fall down. By inappropriate mounting or fracture of hoisting device the load can fall down and cause serious injuries or death. Do not step under suspended loads! Use appropriate hoisting devices and fasteners.
3.3 Construction Layout

1. Arch 2. Upper Table Front 3. Adjustment Leg 4. Reel 5. Foot Bar (Front) 6. Caster (Brake) 7. Reel Brake Release 8. Caster (Free) 9. Foot Pedal (Option) 10. Control Panel 11. Power Cord 12. Strapping Head Unit 13. Main Motor M1 14. Feed Motor M2 15. Tension Motor M3

-A12-

16. Strap Accumulator Motor M4 17. Automatic Feed Motor M5 18. Proximity Sensor SQ1 19. Proximity Sensor SQ2 20. Proximity Sensor SQ3 21. Fan (M11) 22. Heater 23. Photo Eye (Option) 24. Timer Box (Option) 25. Foot Bar (Rear)(Option)
3.4 Installation
1. Remove the packing material and check that the machine is complete and without any shipping damage.
2. Installation of Arch Unit a. Unpack the Arch Unit from the pallet. b. Open the Upper Table Front and take out the package of spare parts from the machine inside. These spare parts are listed as below. c. Loosen the fixing bolt (about 2-3 turns) of Upper Table Rear and then remove it (pull it up and then remove it backward). d. Loosen M7-1-102000 Spring on M7-1-131101 Slide Table Frame and then move M7-1-131600 Slide Table backward. e. Install the Arch Unit to the fixing position and then have 9 sets of spare parts Item D (HBS0616+SW06+PW06A) install in both sides of the Arch Unit, Strap Guide(R) and Strap Guide (L); hand tied them.
-A13-

Package of spare parts Step 1

ITEM

Description M7-1-101300 T7-2-10120 (Guide) HBS0308N + SW03 HBS0616N + SW06+PW06A HBS0630N + PW06A + T7-3-10530+ PW06A + SW06 + HN06 HBS0620N + SW06

• PW06A (For arch size W850mm)
  PMS0316 + SW03 (For SQ6) (OPTION) FMS0508N HBS0508N + SW05 + PW05 (For 850W / 1050W / 1650W) HBS0640HN + PW06B + T7-2-20470 (For 1250W / 1650W)

Qty 1 pc 2 pcs 2 sets 11 sets 1 sets
2 sets or 1set
2 sets
4 pcs 2 sets
2 sets

Step 5 Step 3

Step 2

Step 8

Fig. B
-A13-1-

Step 4 & 8

Step 9

Step 6

Fig. C

Step 10

Step 11 Fig. D

For 1050W/1650W Fig. E

For 1250W/1650W Fig. F

f. Make sure the Arch Unit is vertical (900) to the machine frame and then fix 6 sets of Item D (HBS0616+SW06+PW06A) which are on both sides of Arch Unit.
g. Adjust the position of Guide LH and Guide RH close to the Strap track. The clearance should be smaller than 0.5mm. When the width of arch is 1050W/1650W, its necessary to have Item I parts help to fix Guide LH. (refer to fig. E) When the width of arch is 1250W/1650W, its necessary to have Item J parts help to fix Guide LH & Guide RH. (refer to fig. F)
h. Hook the M7-1-102000 Spring back to M7-1-131101Slide Table Frame (refer to fig. B) and fix M7-1-101300 Eject Plate (L) with correct direction (refer to fig. B). Be sure the Slide Table can move freely after fixing it.

-A13-2-

i. Use Item H parts to fix Control panel onto the right upper side of the Arch Unit. j. Use Item E parts to connect the M7-2-101500 Plate on the left and T7-2-10290
Arm together. (refer to fig. D step 10) k. Fix T7-2-10120 Guide. It can be only a little bit touched with the M7-2-101600
Left Bar or M7-2-101700 Right Bar. l. Connect the Power Cord to the terminal under the Upper Table Front. m. The installation of Arch unit is done. Turn on the machine for following
testing. n. If this machine is with SQ6 option (check chute home position sensor), fix the
SQ6 and make adjustment to have SQ6 is activated before the chute is 1mm away from the home position. If the clearance is too big, it might cause feeding failure; while if the clearance is too small, SQ6 might not able to be activated well. (when testing SQ6, the power should be on so that the led on the SQ6 could be activated.) o. If the width of arch is 1250mm, its necessary to install Connecting Rod Group (M7-2-400000) with Item F parts. (refer to fig. H); if the width of arch is 850mm or 1050mm, its necessary to install Connecting Rod Group (M7-2-400010) with 1set of Item F parts. (refer to fig. I) p. Put back the Upper Table Rear and close the Upper Table Front. Done.

Step 14

Item H

Fig. G

-A13-3-

Step 15

Fig. H

Item F

Fig. I

Item F

3. Adjust the table height by repositioning the screws underneath the machine frame (refer to below drawing). After adjustments, be sure to tighten all the fixing screws.
Caution!
Be sure to take out the wire for the proximity switch underneath the left side of machine to avoid any damage before adjusting the table height.

-A13-4-

4. After positioning the machine ready for working, be sure to lock two front casters (with brake) to avoid machines movements.
5. When moving the machine, be sure to un-lock the two lockable casters. Re- lock the two casters after re-positioning the machine.
6. Do not move the machine unless its necessary. Before movement, be sure to turn off the power, unplug it, put the power cord on the machine and un-lock the front two lockable casters.
7. Minimum Requirements to the Electrical Supply The electrical supply cord for the machine must have a minimum cross-section of at least 1.0 mm2 (16 AWG). The maximum power line fuse must not exceed 16 Amp.
-A13-5-

3.5 Operation Space
Keep the area (A) and (B) free for the operator. The area (A) is necessary for operation strapping machine. The area (B) is necessary for changing the strap or adjusting strap amount in the accumulator.
B
-A14-

3.6 Operating Elements

1. Main Power Switch: Provides the machine with power. Switch to “1” position for turning the main power on. After strapping, switch it to “0” to turn off the machine.

2. LCD Display:
Display strapping message.
2

3. Soft – High Tension Switch:

Switch to right for High strapping tension. Switch to left for soft strapping tension.

3

4
4. Strap Tension Potentiometer:

5

Turn clockwise to increase strapping tension;

turn counter-clockwise to reduce strapping

tension. This potentiometer is only

6

functional under High tension mode)

5. Function Encoder: Turn clockwise or counterclockwise to change strapping settings.

Also! It offers settings for weld cooling time and photo eye timers (expressed in page A21). Other settings can only be changed by technicians with password.
6. Start Switch: When the machine is ready for working, and after turning on Main Power Switch, you must push the Start switch for activating other controls. To initiate a strapping cycle. To clear up machine fault.(reset)

-A15-

7. Reel Release Switch: To release the dispenser for easily taking out strapping from it.
8. Foot Bar : To initiate a strapping cycle. To clear up machine fault. (reset)
9. Foot Pedal Switch (Option): To initiate a strapping cycle. To clear up machine fault. (reset)
10. Photo Eye Switch (Option) The purpose of the photo-eye switch is to automatically initiate strapping cycles when a package is detected. The controls for the photo-eye are shown in the figure below.

Function 0 1
Timer 1 Timer 2

Function
The photo-eye is disabled. The strapping cycle must be initiated with Start switch on the control panel or Foot bar switch and optional foot pedal.
A single strapping cycle: initiates a cycle when a package covers the photo- eye. Delay time for initiating the cycle is controlled by TIMER 1. Multiple strapping cycles: initiates a cycle when a package covers the photo-eye. Cycling continuously until the photo-eye no longer “sees” a package. The cycle timing is determined by TIMER 1 and TIMER 2.
Sets the delay time from the moment that a package is detected until the 1st strapping cycle initiates. This allows an operator to properly position a package for the first strap. It is adjustable from zero to five seconds.
Its the delay time (interval) between strap cycles. When multiple strapping cycles are needed, this timer is for an operator to determine the interval between each straps. It is adjustable from zero to five seconds.

-A16-

11. Foot Bar (Rear)(Option): To initiate a strapping cycle. To clear up machine fault. (reset)
11 3.7 Instructions for Loading PP Strap
3.7.1 Specifications Polypropylene Strap Width: 12mm Thickness: 0.45 -0.65 mm
Strap which has excessive camber as illustrated in figure below cannot be used. Height of 5mm (0.2″) or above
(78.7″)
-A17-

3.7.2 Strap Reel Installation 1. Release the Reel Nut Handle by pressing and turning it to the left. 2. Take out the Outer Flange. 3. Install a new strap coil onto the drum according to the instructions on the reel. 4. Put Outer Flange back and the Reel Nut Handle. Turning the Reel Nut Handle to the right to lock it. 5.Remove the protective straps (B) and the stickers (A) Note: The Reel Nut Handle is released by turning to the left. Tighten it by pressing and turning it to the right.
-A18-

3.8 Auto Strap Feeding Process
1. Turn Main Power Switch on the control panel to the right (at 1 position), and press Start Switch. (refer to Fig. a)
2. Press “Reel Release Switch A” (as shown in Fig. a) and pull out around 60cm strap. (refer to Fig. b)
3. Thread the strap through the Guide Roller B following to the direction showing in Fig. c.
4. Insert the strap to outlet C (refer to Fig. d). 5. Keep threading until the tip of the strap reaches the Accumulator Main Roller. 6. Lift the lever D and insert strap between the rollers E. Feed strap for around
2-3cm ahead the rollers. (refer to Fig. e)

Fig. a.

60cm B
Fig. b.
-A19-

Fig. c.

C Fig. d.

E Fig. e.

B
Caution:
If strap is fed more than 6cm ahead the rollers, it could make Auto Strap Feeding failed.
7. Press Start Switch. Machine will complete the Auto Strap Feeding in 5 sec. and have the strap feeding to the sealing point.
Caution! In the process of Auto Strap Feeding, only the Start Switch is functional. Neither Foot bar switch nor foot pedal switch will function.
Caution! The cut edge of the strap must be free from burrs to avoid failure in Auto Strap Feeding.
-A20-

Operating the Machine

After switching on the strapping machine, heater starts to warm up and LCD display continues to be on until the heater reaches its operating temperature (about 2 minutes).
Caution! Machine will not operate until heater reaches to operating temperature. The heater fans continue to run until heater reaches operating temperature.

Switch Main Power Switch to Position “1”
Heater warms up and LCD display keeps on lightening
Ready! LCD display is off

4.1 Soft Tension Operation

1. Place a package in the middle of table beneath the chute.
2. Push start switch or actuate foot bar switch or foot pedal switch (option) to start strapping.
NOTE! When operating in soft tension mode, the strap tension potentiometer does not function.

4.2 High Tension Operation
1. Place a package in the middle of table beneath the chute.
2. Properly adjust the strap tension potentiometer according to various package.
3. Push start switch or actuate foot bar switch or foot pedal switch (option) to start strapping.
Attention!
Keep hands away from the strapping area.
If hands are caught by P.P. strap accidentally, be sure to turn off the Main Power Switch first and then cut the strap.
-A21-

4.3 Function Encoder
LCD display will show various timers such as cooling time, timer 1, timer 2…etc. After pressing the function encoder for over 2 seconds, turn the knob to choose the timer needed to be changed. Press this knob to confirm the timer needed altered and turn it again to alter the value, and then press it again to confirm this alteration.
T5: cooling time timer, Range 0-0.6S
T1: see A16 timer 1 T2: see A16 timer 2
T4: Press bar delay time, Range 0-3S PH1> 0: Photo eye control box no function
(Disable) 1: Photo eye control box has function
(Enable) PH1-N> 0: only one strap cycle when PH1 is
activated. 1: continuous strap cycles when PH1
is activated and cycle will stop until the package leaves. SQ6> 0: sensor for chute home position no function (Disable) 1: sensor for chute home position has function (Enable) Press>0: Press device no function (Disable) (for TP-702P only)

Ready
Press encoder over 2S
<- Timer TEC
Select Timer and press encoder <-

Turn encoder right

<- T5: 000

0 – 60
Turn encoder right, select the timer needs to be altered and press encoder

<- T5: 000

0 – 60
Turn encoder to change the value Then press encoder

<- T5 : 010

0 – 60
Turn encoder left to <- and press encoder to exit setting

<- Timer TEC
Turn encoder left to <- and press encoder to exit setting

Ready

Finish setting

-A22-

Adjustments

5.1 Strap Amount in the Accumulator Box
The machine has been already well set for storing enough amount of strap in accumulator Box. However, some adjustments may be required, depending on the actual quality or thickness of the strap used. The strap supply in the accumulator box should be sufficient for about 2-5 strapping cycle. (It depends on the package size and the arch size. Fewer cycles are available for bigger arch or bigger package.)
Caution! Excessive amount of strap in the Accumulator Box can lead to the strap jam (too curved) and cause feeding problem. Insufficient amount of strap in the Accumulator Box can lead to short feed problem or decrease strapping speed. The adjusting mechanism for amount of strap is inside the machine, at the rear side of machine. In case that there is an insufficient amount of strap in the Accumulator Box, loosen the Nut A and turn the Screw Bolt B counterclockwise. After adjustments, be sure to tighten the Nut A to avoid unstable strap accumulation.
In case that there is an excessive amount of strap in the Accumulator Box, loosen the Nut A and turn the Screw Bolt B clockwise. After adjustments, be sure to tighten the Nut A to avoid unstable strap accumulation.
B
-A23-

5.2 Adjustment for Feeding Pressure to theAccumulator Box
The machine has been already well set for enough feeding pressure offering enough strength for pulling strap from strap coil to accumulator box. It might be necessary for some adjustments to increase feeding pressure if you are using smooth strap. When its necessary for increasing the feeding pressure, please loosen the Nut A and turn Nut C upwards to increase the strength of Spring B. Be sure to tighten Nut A by turning it counterclockwise after adjustments.
B M4 Motor
C
Caution!
Too much feeding pressure could lead to feeding problem as the strap would be scraped by the rollers easily. Insufficient feeding pressure would lead to short feed problem as the strap is insufficient in the accumulator box.
Thickness of strap
-A24-

5.3 Adjustment for Heater Temperature
The machine has been already well set for proper heater temperature. It might be necessary to do some adjustments according to temperature in working environment, and the quality of PP strap to ensure better sealing efficiency. Turn ,,Aclockwise to increase the heater temperature and turn it counterclockwise to decrease the heater temperature.
5.4 Some adjustments for straps
1. Adjusting “Strap Guide” Adjusting the A (Strap Guide) according to the strap and make sure the width B is around 0.5mm (0.02″) wider than the strap.
Caution: If B is too wide, it would lead to sealing problem. However, if it’s too narrow, it would lead to feeding problem.
-A25-

2. Adjusting “Right Strap Guide”
Loosen the screws on the “Right Strap Guide” and take it out. Then loosen the 2 screws B (HBS0408N) and adjust A according to the strap. Be sure D is about 0.1mm wider than the strap. After adjustment, tighten screws B and put the “Right Strap Guide” back.

HBS0408N

Caution:

M7-2-201400

If D is too wide, it would lead to sealing problem. However, if it’s too narrow, it would lead to feeding problem.

3. Adjusting Brush Clearance in the Arch

The brush clearance in the left side and upper left should be about the strap width. The brush clearance in the upper right should be about 2-3mm narrower to the strap.

The brush clearance in upper side of right chute should be the same to the clearance in right side of upper arch. The brush clearance in the lower right should be 4-5mm narrower to the strap.

Brush clearance

Note: The brush clearance could be various according to different package size. The brush clearance needs to be bigger for not having any effect on reversing especially when the package size is close to the arch size.
-A26-

4. Adjusting Strap Amount in the Accumulator Box Different strap widths might have effects on the strap amount in the accumulator box. Please do the adjustment according to 5.1 if necessary.
5.5 Adjustment for Feeding/Reversing Pressure
The upper table rear was screwed by captive screws. To take it out, please loosening the captive screws about 5mm first and then lift the end side of rear side up and slide it out.
-A27-

1. Adjusting the Pressure for Feeding The machine is already well set for proper feeding pressure. However, according to different strap characteristics (such as smoother surface or different thickness), some adjustments for feeding pressure are still necessary. If short feed problem happens a lot, and it is a result of improper feeding pressure, please do the following adjustments: Loosen Nut B and turn Nut A clockwise to increase the feeding pressure. Or loosen Nut A and turn Nut B counterclockwise to decrease the feeding pressure. After adjustments, be sure to tighten these 2 Nuts well.
B
2. Adjusting the Pressure for Reversing The machine is already well set for proper reversing pressure. However, according to different strap characteristics (such as smoother surface or different thickness), some adjustments for reversing pressure are still necessary. If machine often has incomplete reversing problem, and it is a result of improper reversing pressure, please do the following adjustments: Take out the part (TA-073 Spring Hook) from C position to B or A position in order to increase the reversing pressure.

B C

-A28-

5.6 Adjustment on Tensioning Rollers for High Tension
The machine is already well set for proper pressure for high tension. However, according to different strap characteristics (such as smoother surface or different thickness), some adjustments on pressure for high tension might be necessary. When insufficient strapping tension occurs even the Soft-High tension switch is on “high” position and it is a result of pressure for high tension, please turn Nut D clockwise. This can solve the problem of insufficient strapping tension at high tension and strap slipping between A & B due to this. Note: When the pressure for high tension is set too high, the tension for strapping would get lower.
B
-A29-

Troubleshooting

6.1 LCD Display
When the machine has a malfunction, the LCD will flash and display a failure message. Message shown on the LCD could be as follows:
1. Reminder message: a. Push Start: Please press the Start Switch to make machine function. This is especially necessary after the Safety Switch is released or after you just turn on the machine. b. Load Strap: Load a new roll of strap or re-do the Auto Strap feedingagain. c. B6 open; K1 open: When it shows this message after you press the Start Switch, it means the Safety Switch might not be closed or the K1 in the control box is abnormal.
2. Malfunction from switches: a. S1 Error: This means the Start Switch or the Foot Pedal is continuously triggered before activating them. Please check if any of these 2 Switches is defective. b. S5 Error: This means the Reel Release Switch is continuously triggered before activating it. Try to press it by hand to see if its defective. c. SQ1 on Error: The SQ1 is triggered when doing Auto Strap Feeding. Check if the SQ1 or the Switch lever is defective. d. SQ9 failure: Foot bar is not able to function properly and cause it not able to go back to home position.
3. Malfunction from procedures: a. ASF failed: Auto Strap Feeding failed. It might be caused by wrong inserting direction or inserting strap too much. Please re-do the Auto Strap Feeding. b. Feed jam: Resulting from not being able to feed strap to the sealing position. When Feed jam occurs, solve it by pressing the Start Switch or Foot bar. If this does not solve the problem, please take out the jammed strap by following steps:
-A30-

b-1. Open Upper Table Front Ass’y M7-5-210020. b-2. Lift up the Lever (M7-2-101400/M7-2-101410) with left hand and take
out the Cover (M7-1-311220) for the Upper Guide with right hand at the same time. b-3. Take out the jammed strap and cut it. b-4. Put the cover (M7-1-311220) for the Upper Guide back to its position and put the Upper Table Front Ass’y back as well. Push START switch in the control panel to RESTART machine.

If this does not solve the problem, the following causes have to be checked as well:

Fault 1. Feed jam

Cause

Remedy

Strap is too curved

Change strap

Insufficient feeding pressure Adjust feeding pressure according to

5.5

Too much strap amount in the Adjust to proper strap amount in the

accumulator box and has

accumulator box according to 5.1

caused strap to be curved

Other malfunctions

1. Sealing failure
2. Insufficient strap tension

Too much debris on both sides Clean both sides of the heater plate by

of heater plate

fine sandpaper

Increase the heater temperature

Insufficient heater temperature according to 5.3

Insufficient cooling time

Increase cooling time according to 4.3

Soft-High tension switch is at

“soft” position

Turn it to “high” position

Lubricant drops into tension

roller incautious

Clean the lubricant

Too much debris in the gear of

tension roller

Clean the debris

-A31-

Maintenance

Warning: Before any maintenance or repairs on the machine, set the Main Power Switch to “O” (OFF). Wait about 5 minutes for cooling down the heater to avoid burns with this area. 1. Cleaning and Lubrication
The high reliability and long service life of the strapping machine will depend on regular cleaning and maintenance. ATTENTION! All the important strap transport components, such as the drive rollers and the strap guides, must be kept free from oil and grease. (lubricant)
The lubricant has to be non-resinous. The lubricant is SAE 30
2. Maintenance
Only use original spare parts supplied by manufacturer.
Daily: Use air gun to clean the circled positions (nearby the cutters, strap guide and accumulating feeding rollers) daily Remove plastic residue in the machine.
Air Air
Air
-A32-

Air
Weekly: Lubricate (front bar, press bar and rear bar) and shafts in arch weekly. Please refer to the following mesh areas for instruction. Before lubricating, be sure to clean the parts first to avoid mixing oil and debris which might have a bad effect on machines function.
Test strapping with several bundles, paying attention to audible and visible failures and check for correct function. Monthly 🙁 or 100,000 strapping cycles) Clean both sides of heater plate and polish with fine sandpaper if necessary ATTENTION: Make sure the welding plate is cool first!! Check supporting and cam rollers of seal head for easy movement. The pressure plate must be moved back to home position automatically by the spring tension. Be sure to clean any debris in the tension roller
-A33-

6 Months:or 500,000 strapping cycles Check heating element, replace and re- adjust it if necessary. Check strap cutter in sealing head, replace it if necessary. Check if the connector at wiring housing to printed circuit board is firmly fixed. Check if the safety switch on front table or right door functions well. Make machine ready for operation. Strap one bundle manually several times, paying attention to mal-functions, repeat procedure. Initiating several cyclings with package manually for testing and pay attention to any mal-functions. Make sure the strap accumulating function is well. If necessary, replace the assistant rollers, do proper adjustments to accumulating feeding pressure or to the clearance in the reel brake. Slightly lubricate the sealing head (bearing points) with light lubricant if necessary. 1 year 🙁 or 1,000,000 strapping) Replace deflection roller if it shows visible changes. In case of loud noise at bearings: locate them, replace the bearings. Get machine ready for operation again, strap one bundle manually several times, paying attention to malfunctions.
-A34-

PART II

PC1000-12mm

1. Wiring Diagram
-B1-

-B2-

PC1000-12mm

-B3-

PC1000-12mm

-B4-

PC1000-12mm

-B5-

PC1000-12mm

-B6-

PC1000-12mm

-B7-

PC1000-12mm

-B8-

PC1000-12mm

-B9-

PC1000-12mm

-B10-

PC1000-12mm

-B11-

PC1000-12mm

PART III

1

STRAPPING HEAD UNIT

M7-1-900051

—
Cl-C1-

1

REF. NO.
1 2 3 4

PART NO.
M7-1-100011 M7-1-200000 M7-1-300021 M7-1-400021

STRAPPING HEAD UNIT
DESCRIPTION
Cam Group Bar Guide Group Feed Group Tension Group

M7-1-900051
Q’TY Greenbridge PART #
1 (SEE PG. C3) X 1 (SEE PG. C19) 191709 1 (SEE PG. C27) X 1 (SEE PG. C37) X

-C2-

1-1

CAM GROUP

M7-1-100011

-C3-

1-1

REF.
NO.
1 2 3 4 5 6 7 8 9 10

PART NO.
M7-1-101100 M7-1-101200 M7-1-101300 M7-1-101400 M7-1-101500 M7-1-101600 M7-1-101700 M7-1-101800 M7-1-101900 M7-1-102000

21 M7-1-110001
22 M7-1-120000 23 M7-1-130000 24 M7-1-140000 25 M7-1-150000 26 T7-1-16000

30 H42-1227 31 TA-089 32 T7-1-10330 33 T7-1-10360 34 T7-1-64130

36 LA-40002

38 MB1515 41 SP0514

43 HBS0308N 44 HBS0516N 45 HBS0525HN 46 HBS0640HN 47 HBS0645HN 48 HBS0620N 49 HBS0840HN 50 HBS0865HN 51 HSS0506GN 52 HSS0610GN

CAM GROUP
DESCRIPTION
Strapping Head Frame Guide Ejector Plate (L) Ejector Plate (R) Shaft Collar Cover Sensor Base Coupling Spring
Gear Box and Cam Ass’y M1 Motor Ass’y Slide Table Frame Ass’y Heater Arm Ass’y Exhaust Fan Ass’y Block Ass’y
Washer Spring Hook Bumper Bumper Bracket Return Spring
Label
Metal Bushing, 1515 Spring Pin, 5×14
HBS, M3×8 (N) HBS, M5×16 (N) HBS, M5×25 (H)(N) HBS, M6×40 (H)(N) HBS, M6×45 (H)(N) HBS, M6×20 (N) HBS, M8×40 (H)(N) HBS, M8×65 (H)(N) HSS, M5×6 (G)(N) HSS, M6×10 (G)(N)

55 HN08 58 THS0508N

HN, M8 THS, M5×8 (N)

M7-1-100011
Q’TY Greenbridge PART #
1 X 2 191655 1 191500 1 191496 1 X 1 X 1 191582 1 X 1 X 1 191474
1 SEE PAGE C7 X 1 SEE PAGE C9 X 1 (SEE PG. C11) 191637 1 SEE PAGE C13 1 (SEE PG. C15) 191658 1 SEE PAGE C17 X
3 205661 1 202019 4 191554 2 X 1 191488
1 X
1 191507 2 X
4 191497 4 191700 2 X 3 X 4 X 2 191726 2 X 2 X 2 191584 2 187433
4 187490
2 191579

-C4-

1-1

REF. NO.

PART NO.

61 SW03

62 SW05
63 SW06 64 SW08 65 PW03 66 PW05 67 PW06C

71 HB0620

74 PMS0320

CAM GROUP
DESCRIPTION
SW, M3 SW, M3 (Option) SW, M5 SW, M6 SW, M8 PW, M3 (Option) PW, M5 PW, M6 (C)
HB, M6×20
PMS, M3×20 PMS, M3×20 (Option)

M7-1-100011
Q’TY Greenbridge PART #
10 191590 12 6 191577 13 191562 4 191759 2 187560 2 191578 4 191561
4 X
6 191663 8

-C5-

-C6-

1-1-1

GEAR BOX AND CAM ASS’Y M7-1-110001

-C7-

1-1-1

REF. NO.
1
2 3 4 5 6 7

PART NO.
M7-1-111100 M7-1-111200 M7-1-111300 M7-1-111400 M7-1-111500 M7-1-111600 M7-1-111701

9 M7-1-111900 10 M7-1-112001 11 M7-1-112100 12 M7-1-112201

16 M7-1-110100

21 TB-223 22 T7-1-11240

26 BR6003ZZ

30 KYA020210 31 KYA050530

33 KYA0505101

GEAR BOX AND CAM ASS’Y

M7-1-110001

DESCRIPTION
Retracting Cam Tension Cam Heater Cam Front Bar Cam Press Bar Cam Rear Bar Cam Slide Table Cam

Q’TY Greenbridge PART #
1 X 1 X 1 X 1 X 1 X 1 X 1 X

Support Cam Shaft Position Cam Arch Cam

2 X 1 X 1 X
1 X

Gear Box

1 X

Washer Handle

2 X 1 X

Bearing, 6003ZZ

2 187830

Key, 2×2×10 Key, 5×5×30

1 X 1 X

Key, 5×5×101

2 X

36 CAP06
39 HBS0616N 40 HBS0625N
42 HSS0505GN 43 HSS0606GN
46 SW06

CAP, M6
HBS, M6×16 (N) HBS, M6×25 (N)
HSS, M5×5 (G)(N) HSS, M6×6 (G)(N)
SW, M6

1 X
1 191544 4 X
1 X 9 187305
6 191562

51 HB0616

HB, M6×16

1 191612

-C8-

1-1-2

M1 MOTOR ASS’Y

M7-1-120000

-C9-

1-1-2

REF. NO.

PART NO.

1 M7-1-121100

M1 MOTOR ASS’Y
DESCRIPTION Gear Box Support

6 M7-1-221100

M1 Motor

11 HBS0520N

HBS, M5×20 (N)

16 SW05

SW, M5

21 KYC0210

Key, 2×10

M7-1-120000
Q’TY Greenbridge PART # 1 205946
1 191535
4 191665
4 191577
1 X

-C10-

1-1-3

SLIDE TABLE FRAME ASS’Y M7-1-130000

-C11-

1-1-3

SLIDE TABLE FRAME ASS’Y

M7-1-130000
Greenbridge PAPARTRT# #

191504 191506

-C12-

1-1-4

HEATER ARM ASS’Y

M7-1-140000

-C13-

1-1-4

HEATER ARM ASS’Y

M7-1-140000
Greenbridge PAPARTRT# #

191476 TA

190848

-C14-

1-1-5

EXHAUST FAN ASS’Y

M7-1-150000

-C15-

1-1-5

EXHAUST FAN ASS’Y

M7-1-150000
Greenbridge PAPARTRT# #

X

-C16-

1-1-6

BLOCKASS’Y

T7-1-16000

-C17-

1-1-6

REF. NO.

PART NO.

1 T7-1-10890

Block

BLOCK ASS’Y
DESCRIPTION

6 BR635ZZ

Bearing, 635ZZ

11 SP0516

Spring Pin, 5×16

T7-1-16000
Q’TY Greenbridge PART # 1 X
2 187778
2 205337

-C18-

1-2

BAR GUIDE GROUP

M7-1-200000

25 11
-C19-

1-2

REF. NO.

PART NO.

1 M7-1-201100

2 M7-1-201200

M7-1-201200S

3 M7-1-201300

M7-1-201300EN

4 M7-1-201400

M7-1-201400EN

BAR GUIDE GROUP

M7-1-200000

DESCRIPTION

Q’TY Greenbridge PART #

Bar Guide Bar Guide Lid Bar Guide Lid (Stainless Steel Model)(Option) Cutter Holder Cutter Holder (Stainless Steel Model)(Option) Strap Guide Strap Guide (Stainless Steel Model)(Option)

1 191527 1 191724 1 191550 1 191626 1 191549 1 191512
1 191657

6 M7-1-210001 M7-1-210001S
7 M7-1-220000 M7-1-220000S
8 M7-1-230000 M7-1-230000S
11 TA-071 12 T7-1-10180

Front Bar Ass’y

1 (SEE PG.C21) 191477

Front Bar Ass’y (Stainless Steel Model)(Option) 1 191614

Press Bar Ass’y

1 (SEE PAGE C23) 191478

Press Bar Ass’y (Stainless Steel Model)(Option) 1 191615

Rear Bar Ass’y

1 (SEE PAGE C25) 191525

Rear Bar Ass’y (Stainless Steel Model)(Option) 1 191616

Return Spring Spring Hook

3 191479 1 191725

21 HBS0308N 22 HBS0520N 23 HBS0616N 24 HBS0620N 25 HBS0650HN
27 SW05 28 SW06

HBS, M3×8 (N) HBS, M5×20 (N) HBS, M6×16 (N) HBS, M6×20 (N) HBS, M6×50 (H)(N)
SW, M5 SW, M6

31 HN05

HN, M5

3 191497 1 191665 2 191544 2 191726 2 191727
1 191577 6 191562
1 187478

-C20-

1-2-1

FRONT BAR ASS’Y

M7-1-210001

-C21-

1-2-1

REF. NO.
1

PART NO.
M7-1-210001 M7-1-210001S M7-1-211101 M7-1-211101S

6 TA-073 7 TA-078 8 T7-1-13121

FRONT BAR ASS’Y

M7-1-210001

DESCRIPTION

Q’TY Greenbridge PART #

Front Bar Ass’y

1 191477

Front Bar Ass’y (Stainless Steel Model)(Option) 1 191614

Front Bar Front Bar (Stainless Steel Model)(Option)

1 191602 1 X

Spring Hook Spring Plunger

1 191747 1 191516 1 191654

11 BRNART6VR
13 SP0318 14 SP0616

Bearing, NART6VR
Spring Pin, 3×18 Spring Pin, 6×16

1 191644
1 190797 1 191698

-C22-

1-2-2

PRESS BAR ASS’Y

M7-1-220000

-C23-

1-2-2

REF. NO.
1

PART NO.
M7-1-220000 M7-1-220000S M7-1-221200 M7-1-221200S

6 TA-073 7 TA-078 8 T7-1-13121

PRESS BAR ASS’Y

M7-1-220000

DESCRIPTION

Q’TY Greenbridge PART #

Press Bar Ass’y

1 191478

Press Bar Ass’y (Stainless Steel Model)(Option) 1 191615

Press Bar

1 191633

Press Bar (Stainless Steel Model)(Option)

1 X

Spring Hook Spring Plunger

1 191747 1 191516 1 191654

11 BRNART6VR
13 SP0318 14 SP0616

Bearing, NART6VR
Spring Pin, 3×18 Spring Pin, 6×16

1 191644
1 190797 1 191698

-C24-

1-2-3

REAR BAR ASS’Y

M7-1-230000

-C25-

1-2-3

REF. NO.
1

PART NO.
M7-1-230000 M7-1-230000S M7-1-231100 M7-1-231100S

6 TA-073 7 TA-078 8 T7-1-13121

REAR BAR ASS’Y

M7-1-230000

DESCRIPTION

Q’TY Greenbridge PART #

Rear Bar Ass’y Rear Bar Ass’y (Stainless Steel Model)(Option) Rear Bar Rear Bar (Stainless Steel Model)(Option)

1 191525 1 191616
1 191685 1 X

Spring Hook Spring Plunger

1 191747 1 191516
1 191654

11 BRNART6VR
13 SP0318 14 SP0616

Bearing, NART6VR
Spring Pin, 3×18 Spring Pin, 6×16

1 191644 1 190797 1 191698

-C26-

1-3

FEED GROUP

M7-1-300021

-C27-

1-3

REF. NO.
3 4

PART NO.
M7-1-301300 M7-1-301420

FEED GROUP
DESCRIPTION Bearing Housing Guide Wheel

M7-1-300021
Q’TY Greenbridge PART # 1 1918124 1 191822

8 M7-1-300100
11 M7-1-310021 M7-1-310021S
12 M7-1-320020 13 M7-1-330000 14 M7-1-340000
18 BR6002ZZ
22 KYA040415
25 HBS0412N 26 HBS0512N 27 HBS0516N 28 HBS0612N 31 TMS0508
34 SW04 35 SW05 36 SW06 38 PW04 39 PW05 40 PW06A 41 PW06C

Feeding Motor (M2) Set
Upper Guide Ass’y Upper Guide Ass’y (Stainless Steel Model) (Option) Assistant Roller Ass’y Feeding Arm Ass’y Retracting Arm Ass’y
Bearing, 6002ZZ
Key, 4×4×15
HBS, M4×12 (N) HBS, M5×12 (N) HBS, M5×16 (N) HBS, M6×12 (N) TMS, M5×8
SW, M4 SW, M5 SW, M6 PW, M4 PW, M5 PW, M6 (A) PW, M6 (C)

1 191537
1 (SEE PG. C29) 191792 1 X
1 (SEE PG. C31) 191820 1 (SEE PG. C33) 1 (SEE PG. C35)
1 187782
1 204624
2 191682 2 190848 6 191700 3 191563 1 X
2 X 8 191577 3 191562 2 187428 2 191578 1 191612 2 191561

-C28-

1-3-1

UPPER GUIDE ASS’Y

M7-1-310021

-C29-

1-3-1

UPPER GUIDE ASS’Y

M7-1-310021
Greenbridge PAPARTRT# #
X X

-C30-

1-3-2
/

ASSISTANT ROLLER ASS’Y M7-1-320020

-C31-

1-3-2

REF. NO.
1

PART NO.
M7-1-321120 M7-1-321120EN

2 M7-1-321200
3 M7-1-321300 4 M7-1-321420 5 M7-1-321501 6 M7-1-321600

ASSISTANT ROLLER ASS’Y
DESCRIPTION
Assistant Roller Bracket Assistant Roller Bracket (Stainless Steel Model)(Option) Shaft Assistant Roller Base Assistant Roller SQ8 Sensor Base Spacer

M7-1-320020
Q’TY Greenbridge PART #
1 X 1 X
2 X 1 X 1 191828 1 205935 1 191599

11 BR686ZZ
13 HBS02.512N 14 HBS0512N
16 HBS0425N 17 HBS0620N
19 SW02.5 20 SW04 21 SW05

Bearing, 686ZZ
HBS, M2.5×12 (N) HBS, M5×12 (N)
HBS, M4×25 (N) HBS, M6×20 (N)
SW, M2.5 SW, M4 SW, M5

2 191598
1 X 4 190848
2 X 1 191726
1 X 2 X 4 191577

26 PW05 30 HN02.5

PW, M5 HN, M2.5

2 191578 1 X

-C32-

1-3-3

FEEDING ARM ASS’Y

M7-1-330000

-C33-

1-3-3

REF. NO.
1
2 3 4 5

PART NO.
M7-1-331100 M7-1-331200 M7-1-331300 M7-1-331400 M7-1-331500

FEEDING ARM ASS’Y
DESCRIPTION
Feeding Arm Linkage Shaft Collar Spring Hook

11 T7-1-64130

Return Spring

14 BR6901ZZ

Bearing, 6901ZZ

17 HBS0616N 18 HBS0640N

HBS, M6×16 (N) HBS, M6×40 (N)

23 PMS0420

PMS, M4×20

26 HN04 27 HN06

HN, M4 HN, M6

31 SW04 32 SW06

SW, M4 SW, M6

35 PW06C

PW, M6 (C)

M7-1-330000
Q’TY Greenbridge PART #
1 X 1 X 1 X 1 X 1 X

1 191488

2 198856

1 1

191544 188671

1 187902

1 3

191604 191611

1 X 3 191562

1 191561

-C34-

1-3-4

RETRACTING ARM ASS’Y

M7-1-340000 I

-C35-

1-3-4

REF. NO.
1 2

PART NO.
M7-1-341100 M7-1-341200

RETRACTING ARM ASS’Y

M7-1-340000

DESCRIPTION
Retracting Arm Shaft

Q’TY Greenbridge PART #
1 X 1 X

6 TA-073

Spring Hook

1 191747

11 BR635ZZ

Bearing, 635ZZ

1 187778

14 MB1015

Metal Bushing, 1015

1 X

17 HBS0516N

HBS, M5×16 (N)

1 191700

21 HB0612

HB, M6×12

1 205333

24 SW05 25 SW06

SW, M5 SW, M6

1 191577 1 191562

29 PW05 30 PW06B

PW, M5 PW, M6 (B)

2 191578 1 X

-C36-

1-4

TENSION GROUP

M7-1-400021

-C37-

1-4

TENSION GROUP

M7-1-400021

Greenbridge PAPARTRT# #

X 191857 X

X

-C38-

1-4-1

TENSION CRANK ASS’Y

M7-1-410020

-C39-

1-4-1

TENSION CRANK ASS’Y

M7-1-410020
Greenbridge PAPARTRT# #

188671 X 191611 X
-C40-

1-4-2

TENSION ARM ASS’Y

M7-1-420011

-C41-

1-4-2

REF. NO.
1 2

PART NO.
M7-1-421101 M7-1-421200

4 M7-1-421400 5 M7-1-421520 6 M7-1-421600 7 M7-1-421700 8 M7-1-421800 9 M7-1-421900 10 M7-1-420100
11 TB-223

TENSION ARM ASS’Y
DESCRIPTION
Tension Arm Shaft
Spring Support Spring Nut Collar Connecting Rod (Upper) Connecting Rod (Lower) Connecting Rod Set Washer

16 BRCF8 17 BR6902ZZ
18 HB0612
21 FLG06

Bearing, CF8 Bearing, 6902ZZ
HB, M6×12
FLG, M6

M7-1-420011
Q’TY Greenbridge PART # 1 X 1 X
1 205490 1 191729 1 205491 1 X 1 203918 1 X 1 204692 1 X
1 191643 2 X
1 205333
1 205492

24 SW06 25 SW08
28 PW06A

SW, M6 SW, M8
PW, M6 (A)

1 191562 1 191759
1 191612

31 HN08

HN, M8

1 187490

-C42-

BANDWAY UNIT

M7-2-900021

-C43-

BANDWAY UNIT

M7-2-900021
Greenbridge PAPARTRT# # X X

-C44-

2-1

ARCH GROUP

M7-2-100010

-C45-

2-1

REF. NO.

PART NO.
M7-2-100010 M7-2-100010S

3 M7-2-101310 M7-2-101360 M7-2-101340 M7-2-101350
4 M7-2-101400 M7-2-101410
5 M7-2-101500 M7-2-101510
6 M7-2-101600 M7-2-101610 M7-2-101620 M7-2-101630
7 M7-2-101700 M7-2-101710 M7-2-101720 M7-2-101730
8 M7-1-101600 9 TB-223

11 T7-2-10110 12 T7-2-10120
T7-2-10770 13 T7-2-10221
T7-2-10222 T7-2-10223 T7-2-10224 T7-2-10226 14 T7-2-10230
17 T7-2-10260

19 T7-2-10290 24 T7-3-10530
31 WT163015

35 BRCF8 36 BRNAST6

ARCH GROUP
DESCRIPTION
Arch Group Arch Group (Stainless Steel Model)
Rod (For 650W) Rod (For 850W) Rod (For 1050/1250W) Rod (For 1650W) Lever (For 650W) Lever (For 850W~1650W) Plate (For 400H~800H) Plate (For 1000H) Left Bar (For 400H) Left Bar (For 500H) Left Bar (For 600H) Left Bar (For 800H/1000H) Right Bar (For 400H) Right Bar (For 500H) Right Bar (For 600H) Right Bar (For 800H/1000H) Collar Washer (For 400H/500H) Washer (For 600H) Washer (For 800H/1000H) Bushing Guide (For 400H~800H) Guide (For 1000H) Connecting Rod (For 650W) Connecting Rod (For 850W) Connecting Rod (For 1050W) Connecting Rod (For 1250W) Connecting Rod (For 1650W) Connector
Spacer (For 400H/500H) Spacer (For 600H) Spacer (For 800H/1000H) Arm Tube
Thrust Washer (For 400H/500H) Thrust Washer (For 600H) Thrust Washer (For 800H/1000H) Bearing, CF8 Bearing, Nast6 (For 850W~1650W)

-C46-

M7-2-100010
Q’TY Greenbridge PART #
1 X 1 X
1 X 1 X 1 X 1 X 1 X 1 X 1 205334 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 4 X 6 8 2 191699 2 205498 2 X 1 X 1 X 1 X 1 X 1 X 2 X
4 191672 6 8 1 X 6 191670
4 X 6 8 1 191643 1 191683

2-1

REF. NO.

PART NO.

38 MB0806

41 KYA050510

ARCH GROUP
DESCRIPTION Metal Bushing, 0806 Key, 5×5×10

M7-2-100010
Q’TY Greenbridge PART # 6 X 1 X

47 HBS0516N HBS0516S
49 HBS0616N 50 HBS0620N 51 HBS0630N 52 HBS0830N 56 THS0612N
THS0612S
57 THS0625N 58 THS0630N
THS0630S
61 HN06
62 HSS0506GN 63 HSS0608GN 66 SW05
SW05S 67 SW06 68 SW08

HBS, M5×16 (N) HBS, M5×16 (Stainless Steel Model)
HBS, M6×16 (N)(For 400H~1000H) HBS, M6×20 (N) HBS, M6×30 (N) HBS, M8×30 (N)
THS, M6×12 (N)(Only 1000H) THS, M6×12 (Stainless Steel Model)(Only 1000H) THS, M6×25 (N)(For 850W~1650W) THS, M6×30 (N)(For 400H/500H) THS, M6×30 (N)(For 600H) THS, M6×30 (N)(For 800H/1000H) THS, M6×30 (Stainless Steel Model) (For 400H/500H) THS, M6×30 (Stainless Steel Model) (For 600H) THS, M6×30 (Stainless Steel Model) (For 800H/1000H) HN, M6 (For 400H/500H) HN, M6 (For 600H) HN, M6 (For 800H/1000H) HSS, M5×6 (G)(N) HSS, M6×8 (G)(N)
SW, M5 SW, M5 (Stainless Steel Model) SW, M6 SW, M8

2 191700 2 205331

2 191544 1 191726 5 191779 2 X

2 2

X X

1 X 4 X 6 8 4 X

6

8

14 191611 16
18
2 191584 1 X

2 191577 2 X 17~21 191562 3 191759

72 PW06A

PW, M6 (A)(For 650W) PW, M6 (A)(For 850W~1650W)

19 191612 21

-C47-

-C48-

2-2

BANDWAY GROUP

M7-2-200021

-C49-

2-2

BANDWAY GROUP

M7-2-200021

Greenbridge PAPARRTT# #
X X

191735
X X

X X

-C50-

2-2-1

STRAP TRACK FRAME ASS’Y

M7-2-210021
Greenbridge PAPARRTT# # X X

X X X X X

X
-C52-

2-2-1

REF. NO.

PART NO.

33 HBS0412N

34 HBS0612N 35 HBS0540N

38 TMS0408

STRAP TRACK FRAME ASS’Y

M7-2-210021

DESCRIPTION
HBS, M4×12 (N)(For 650W~1050W) HBS, M4×12 (N)(For 1250W/1650W) HBS, M6×12 (N) HBS, M5×40 (N)(Without SQ6 Option)

Q’TY Greenbridge PART #
7 X 8 8 X 1 X

TMS, M4×8 (For 650W~1050W) TMS, M4×8 (For 1250W/1650W)

4 191648 6

41 SR08
43 HN04 44 HN05
46 SW04
47 SW05
48 SW06 51 PW04
52 PW06C 53 PW05

Stop Ring, S-8
HN, M4 HN, M5 (Without SQ6 Option)
SW, M4 (For 650W~1050W) SW, M4 (For 1250W/1650W) SW, M5 SW, M5 (Without SQ6 Option) SW, M6
PW, M4 (For 650W~1050W) PW, M4 (For 1250W/1650W) PW, M6 (C) PW, M5 (Without SQ6 Option)

4 X

16 2

191604 187478

22 X 24 2 191577 3 8 191562

22 187428 24
8 191561 1 191578

-C53-

-C54-

2-3

REF. NO.
1

PART NO.
M7-2-300011 M7-2-300011S M7-2-301101 M7-2-301101S

M7-2-301111 M7-2-301111S

M7-2-301121 M7-2-301121S

M7-2-301131 M7-2-301131S

M7-2-301141 M7-2-301141S

2 FR-12006300 3 FR-12006301 4 M7-2-310000 5 T5-4-10580 6 M7-2-101110
M7-2-101110S M7-2-101160 M7-2-101160S M7-2-101170 M7-2-101170S M7-2-101140 M7-2-101140S M7-2-101150 M7-2-101150S 7 M7-2-101210 M7-2-101210S
M7-2-101220
M7-2-101220S

M7-2-101230 M7-2-101230S

8 M7-2-301800 M7-2-301800S

10 T7-2-20470

ARCH COVER GROUP

M7-2-300011

DESCRIPTION

Q’TY Greenbridge PART #

Arch Cover Group Arch Cover Group (Stainless Steel Model) Arch Cover RH (For 400H) Arch Cover RH (Stainless Steel Model) (For 400H) Arch Cover RH (For 500H) Arch Cover RH (Stainless Steel Model) (For 500H) Arch Cover RH (For 600H) Arch Cover RH (Stainless Steel Model) (For 600H) Arch Cover RH (For 800H) Arch Cover RH (Stainless Steel Model) (For 800H) Arch Cover RH (For 1000H) Arch Cover RH (Stainless Steel Model) (For 1000H) Foam Rubber Foam Rubber Block Ass’y (For 650W~1050W) Grommet Guide LH (For 650W) Guide LH (Stainless Steel Model)(For 650W) Guide LH (For 850W) Guide LH (Stainless Steel Model)(For 850W) Guide LH (For 1050W) Guide LH (Stainless Steel Model)(For 1050W) Guide LH (For 1250W) Guide LH (Stainless Steel Model)(For 1250W) Guide LH (For 1650W) Guide LH (Stainless Steel Model)(For 1650W) Guide RH (For 650W) Guide RH (Stainless Steel Model)(For 650W) Guide RH (For 850W/1050W) Guide RH (Stainless Steel Model) (For 850W/1050W) Guide RH (For 1250W/1650W) Guide RH (Stainless Steel Model) (For 1250W/1650W)
Cover Cover (Stainless Steel Model)

1 X 1 X 1 X 1 X
1 X 1 X
1 X 1 X
1 X 1 X
1 X 1 X
1 X 1 X 1 (SEE PG. C61) X 1 191803 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X 1 X
1 X 1 X
1 X 1 X

Support Rod (For 1250W/1650W)

2 X

-C56-

2-3

ARCH COVER GROUP

M7-2-300011

Greenbridge PAPARRTT# #

X X X X X X X X X X
-C57-

2-3

REF. NO. 18 19 20

PART NO.
LA-40005 HBS0412N HBS0508N HBS0508S

21 HBS0512N HBS0512S
22 HBS0616N

24 HBS0640HN

25 HBS0616S

26 TTP0412BN

TTP0412BS

28 THS0508N THS0508S
30 TMS0406 TMS0406S
31 PMS0316 32 SW03 33 SW05
34 SW05S
35 SW06
36 SW06S 37 SW04 39 PW04 40 PW05

41 PW05S 42 PW06A

ARCH COVER GROUP
DESCRIPTION
Label HBS, M4×12 (N)(For 650W~1050W) HBS, M5×8 (N)(For 1050W/1650W) HBS, M5×8 (Stainless Steel Model) (For 1050W/1650W) HBS, M5×12 (N) HBS, M5×12 (Stainless Steel Model) HBS, M6×16 (N)(For 650W~1050W) HBS, M6×16 (N)(For 1250W/1650W) HBS, M6×40 (H)(N)(For 850W/1050W) HBS, M6×40 (H)(N)(For 1250W/1650W) HBS, M6×16 (Stainless Steel Model) (For 650W~1050W) TTP, M4×12 (B)(N)(For 650W~1050W) TTP, M4×12 (B)(N)(For 1250W/1650W) TTP, M4×12 (B)(Stainless Steel Model) (For 650W~1050W) TTP, M4×12 (B)(Stainless Steel Model) (For 1250W/1650W) THS, M5×8 (N) THS, M5×8 (Stainless Steel Model)
TMS, M4×6 TMS, M4×6 (Stainless Steel Model) PMS, M3×16 (Option) SW, M3 (Option) SW, M5 (For 650W/850W/1250W) SW, M5 (For 1050W/1650W) SW, M5 (Stainless Steel Model) (For 1050W/1650W) SW, M6 (For 650W) SW, M6 (For 850W/1050W) SW, M6 (For 1250W/1650W) SW, M6 (Stainless Steel Model) SW, M4 (For 650W~1050W) PW, M4 (For 650W~1050W) PW, M5 (For 650W) PW, M5 (For 1250W) PW, M5 (For 1050W) PW, M5 (For 1650W) PW, M5 (Stainless Steel Model) (For 1050W/1650W) PW, M6 (A)(For 650W~1050W) PW, M6 (A)(For 1250W/1650W)

M7-2-300011
Q’TY Greenbridge PART #
2 191797 2 191682 2 202943 2 X
3 190848 3 X 3 191544 4 4 X 6 3 204086
9 191701 12 9 X
12
12 191579 12 205600
3 X 3 X 2 X 2 191590 3 191577 5 2 X
3 191562 7 8 3 205539 2 X 2 187428 3 191578 4 5 6 4 X
3 191612 4

-C58-

2-3

REF. NO. 43

PART NO.
PW06B PW06BS

ARCH COVER GROUP
DESCRIPTION
PW, M6 (B)(For 1250W/1650W) PW, M6 (B)(Stainless Steel Model) (For 1250W/1650W)

M7-2-300011
Q’TY Greenbridge PART # 2 X 2 205540

-C59-

-C60-

2-3-1

BLOCKASS’Y (For 650W–1050W)

M7-2-310000

-C61-

2-3-1

REF. NO.

PART NO.

1 M7-2-301200

BLOCK ASS’Y (For 650W~1050W)

Block

DESCRIPTION

6 BR635ZZ

Bearing, 635ZZ

11 HBS0516N

HBS, M5×16 (N)

16 PW05

PW, M5

21 SW05

SW, M5

M7-2-310000
Q’TY Greenbridge PART # 1 X 2 187778 2 191700 2 191578 2 191577

-C62-

2-4-1

CONNECTING ROD GROUP M7-2-400010 (For 850W/1050W)

-C62-1-

2-4-1

REF. NO.
2 3 4 5 6 7

PART NO.
M7-2-401210 M7-2-401300 M7-2-401400 M7-2-401500 M7-2-401600 M7-2-401700

CONNECTING ROD GROUP (For 850W/1050W)

M7-2-400010

DESCRIPTION
Connecting Rod Connector Slant Block Bracket (Left) Bracket (Right) Collar

Q’TY Greenbridge PART #
1 X 1 X 1 X 1 X 1 X 2 203833

11 T7-2-20560

Swivel Head, NHS06

16 MB1715
19 HSS0506GN
21 HBS0616N 22 HBS0620N

Metal Bushing, 1715
HSS, M5×6 (G)(N)
HBS, M6×16 (N) HBS, M6×20 (N)

25 HBS0635HN 29 HN06 30 NTE06

HBS, M6×35 (H)(N) HN, M6 NTE, M6

33 SW06

SW, M6

36 PW06A 37 PW06C

PW, M6 (A) PW, M6 (C)

1 X
2 X 2 191584 4 191544 2 191726
2 X 7 191611 1 X
8 191562
2 191612 6 191561

-C62-2-

2-4-2

CONNECTING ROD GROUP M7-2-400000 (For 1250W/1650W)

—

C63-

2-4-2

CONNECTING ROD GROUP

(For 1250W/1650W)

M7-2-400000

REF. NO.
1 2 3 4

PART NO.
M7-2-401100 M7-2-401200 M7-2-401300 M7-2-401400

DESCRIPTION
Bracket Connecting Rod Connector Slant Block

Q’TY Greenbridge PART #
2 X 1 X 2 X 1 X

9 TC-025 10 H42-1227 11 T7-2-20560

Spring Washer Swivel Head, NHS06

1 191524 2 205661
2 X

16 MB1512

Metal Bushing, 1512

2 X

22 HBS0620N
24 HBS0630N 25 HBS0635HN 29 HN06 30 NTE06

HBS, M6×20 (N)
HBS, M6×30 (N) HBS, M6×35 (H)(N) HN, M6 NTE, M6

33 SW06

SW, M6

36 PW06A 37 PW06C

PW, M6 (A) PW, M6 (C)

7 191726 1 191779 2 X 6 191611 2 X
10 191562
2 191612 6 191561

-C64-

3

ACCUMULATOR UNIT

M7-3-900020

M7-3-900071

-C65-

3

ACCUMULATOR UNIT

M7-3-900020

M7-3-900071

Greenbridge PAPARRTT# #
X X

X X

X X

X X

-C66-

3-1

STRAP AMOUNT CONTROL GROUP M7-3-100020

-C67-

3-1

STRAP AMOUNT CONTROL GROUP M7-3-100020

REF. NO.
1 2 3

PART NO.
T7-3-10150 M7-3-101200 M7-3-101300

Shaft Spring Balance Bar

DESCRIPTION

Q’TY Greenbridge PART #
1 X 1 191523 1 X

6 TF-007

Micro Switch

1 191481

8 T6-3-10130 9 T6-3-10200

Accumulator Adjusting Bolt Twist Stopper

1 X 1 191703

11 T7-3-10180 12 T7-3-10200

Tube Sensor Lever

1 X 1 202742

16 BR6900ZZ

Bearing, 6900ZZ

2 187996

21 HBS0410N 24 FMS0410

HBS, M4×10 (N) FMS, M4×10

2 X 4 191786

27 PMS0316
31 HSS0405GN
34 HN03 35 HN08

PMS, M3×16
HSS, M4×5 (G)(N)
HN, M3 HN, M8

3 X
2 X
1 X 1 187490

39 SW03 40 SW04 41 SW08

SW, M3 SW, M4 SW, M8

3 191590 2 X
1 191759

-C68-

3-2

AUTO STRAP FEEDING GROUP

M7-3-200020

C69-

3-2

AUTO STRAP FEEDING GROUP M7-3-200020

Greenbridge PAPARRTT# #
X X

X X
X X
X
X X

-C70-

3-2

REF. NO. 41 42

PART NO.
SW05 SW05S

45 PW04 PW04S
46 PW05 PW05S

49 HN06

53 HSS0506GN 54 HSS0508GN

AUTO STRAP FEEDING GROUP M7-3-200020

DESCRIPTION
SW, M5 SW, M5 (Stainless Steel Model)

Q’TY Greenbridge PART #
10 191577 4 X

PW, M4 PW, M4 (Stainless Steel Model) PW, M5 PW, M5 (Stainless Steel Model)

2 187428 2 205543 4 191578 4 X

HN, M6

2 191611

HSS, M5×6 (G)(N) HSS, M5×8 (G)(N)

2 191584 2 X

-C71-

-C72-

3-2-1

ROLLER ASS’Y

M7-3-210010

-C73-

3-2-1

ROLLER ASS’Y

M7-3-210010
Greenbridge PAPARRTT# # X X
191755 X X X
X

-C74-

3-2-2

MOVABLE STRAP GUIDE ASS’Y M7-3-220020

-C75-

3-2-2

MOVABLE STRAP GUIDE ASS’Y

M7-3-220020

REF. NO.
1 2 3 4

PART NO.
M7-3-221101 M7-3-221200 M7-3-221300 M7-3-221420

DESCRIPTION
Rotary Arm Spacer Link Movable Strap Guide

Q’TY Greenbridge PART #
1 X 2 X 1 X 1 X

8 BR605ZZ

Bearing, 605ZZ

2 190823

11 HBS0510N 12 HBS0525N

HBS, M5×10 (N) HBS, M5×25 (N)

1 X 1 X

16 SW05

SW, M5

4 191577

21 PW05

PW, M5

2 191578

26 HN05 31 FMS0520

HN, M5 FMS, M5×20

2 187478 1 X

-C76-

3-2-3

M4 MOTOR ASS’Y

M7-3-230020

-C77-

3-2-3

REF. NO.

PART NO.

1 M7-3-231120

4 M7-3-230100

8 TB-223 9 T7-3-20110

M4 MOTOR ASS’Y
DESCRIPTION Accumulator Main Roller
M4 Motor Set
Washer Motor Support

M7-3-230020
Q’TY Greenbridge PART # 1 191546 1 191538 1 X 1 191567

13 MB1010 16 KYA050515

Metal Bushing, 1010 Key, 5×5×15

2 191568 1 X

19 HBS0512N 20 HBS0612N
23 SW06

HBS, M5×12 (N) HBS, M6×12 (N)
SW, M6

4 190848 1 191563 1 191562

-C78-

3-2-4
.
/

INLET STRAP GUIDE ASS’Y M7-3-240000

-C79-

3-2-4

INLET STRAP GUIDE ASS’Y

M7-3-240000
Greenbridge PPAARRTT# #
X X X X X X

X X

-C80-

205628 X

3-2-4

REF. NO. 37
38

PART NO.
SW04 SW04S SW05 SW05S

41 PW04 PW04S
42 PW05 PW05S

45 HN04 HN04S

INLET STRAP GUIDE ASS’Y

M7-3-240000

DESCRIPTION
SW, M4 SW, M4 (Stainless Steel Model) SW, M5 SW, M5 (Stainless Steel Model)

Q’TY Greenbridge PART #

7 X

7 X

2 2

191577 X

PW, M4 PW, M4 (Stainless Steel Model) PW, M5 PW, M5 (Stainless Steel Model)

2 187428
2 205543
2 191578 2 X

HN, M4 HN, M4 (Stainless Steel Model)

1 191604 1 205397

-C81-

-C82-

3-2-5

ASSISTANT ROLLER SHAFT ASS’Y T7-3-20082

-C83-

3-2-5

ASSISTANT ROLLER SHAFT ASS’Y T7-3-20082

REF. NO.
1 2 3

PART NO.
T7-3-20150 T7-3-20163 T7-3-20200

DESCRIPTION
Shaft Assistant Roller Spacer

Q’TY Greenbridge PART #
1 X 1 191754 1 191755

6 T7-3-20102

Assistant Roller Ass’y

1 204529

11 BR608ZZ 16 HN08 21 SW08

Bearing, 608ZZ HN, M8 SW, M8

2 187783 1 187490 1 191759

-C84-

3-3

ACCUMULATOR BOX GROUP M7-3-300020

a.

(For 650W–1050W)

M7-3-300071

–

C85-

3-3

ACCUMULATOR BOX GROUP

M7-3-300020

a.

(For 650W~1050W)

M7-3-300071

Greenbridge PAPARRTT# #

X
-C86-

3-3

ACCUMULATOR BOX GROUP M7-3-300081

b.

(For 1250W/1650W)

-C87-

3-3

ACCUMULATOR BOX GROUP

M7-3-300081

b.

(For 1250W/1650W)

Greenbridge PAPARRTT# #

X

-C88-

4

REEL CONTROL GROUP

M7-4-100020

M7-4-100030

-C89-

4

REEL CONTROL GROUP

M7-4-100020

M7-4-100030

Greenbridge PAPARRTT# #
X X

X X

-C90-

4-1

REEL CONTROL GROUP

M7-4-100020

I
-C91-

4-1

REEL CONTROL GROUP

M7-4-100020

M7-4-100030

Greenbridge PAPARRTT# #
X X

X X

191638 X

X X
X X
X X
X
X

-C92-

4-1-1

OUTER FLANGE ASS’Y

M7-4-110020 M7-4-110030

-C93-

4-1-1

OUTER FLANGE ASS’Y

M7-4-110020 M7-4-110030
Greenbridge PAPARRTT# # X X
X X
X X

-C94

-C95-

4-1-2

REEL CRANK ASS’Y

Greenbridge PAPARRTT# # X X
X X

-C96-

4-1-2

REEL CRANK ASS’Y

REF. NO. 44
45
46
49
50

PART NO.
SW05 SW05S SW06 SW06S SW08 SW08S PW06C PW06CS PW08C PW08CS

DESCRIPTION
SW, M5 SW, M5 (Stainless Steel Model) SW, M6 SW, M6 (Stainless Steel Model) SW, M8 SW, M8 (Stainless Steel Model) PW, M6 (C) PW, M6 (C)(Stainless Steel Model) PW, M8 (C) PW, M8 (C)(Stainless Steel Model)

Q’TY Greenbridge PART #
4 191577 4 X 5 191562 5 205539 1 191759 1 X 4 191561 4 205534 1 191760 1 X

-C97-

-C98-

5

BODY FRAME UNIT

M7-5-900111

M7-5-900121

-C99-

BODY FRAME UNIT

Greenbridge PAPARRTT# # X X
X X
X X
X X
X X
X X
X
X
X
X X
X X
X X
X X
X X
X X

-C100-

BODY FRAME UNIT

REF. NO.
3

PART NO.
M7-5-300041 M7-5-300041S

M7-5-300051 M7-5-300051S

4 T7-6-40001

DESCRIPTION

Q’TY Greenbridge PART #

Extension Table Group (For 1050W) Extension Table Group (Stainless Steel Model) (For 1050W) Extension Table Group (For 1650W) Extension Table Group (Stainless Steel Model) (For 1650W) Pedal Control Set (Option)

1 (SEE PG.C127) X 1 X
1 X 1 X
1 (SEE PG.C135) 191529

-C101-

-C102-

5-1

BODY FRAME WITH

M7-5-100111

FOOT BAR GROUP

–M—7—-5-100121

/ //
-C103-

5-1

BODY FRAME WITH

FOOT BAR GROUP

Greenbridge PAPARRTT# #
X X

X

X X X

X X X X
X

191531

X

-C104-

204725

5-1

BODY FRAME WITH

FOOT BAR GROUP

Greenbridge PAPARRTT# # X

191533 X

191534 X

X

-C105-

5-1

REF. NO.

PART NO.

28 PW06A

PW06AS

BODY FRAME WITH FOOT BAR GROUP
DESCRIPTION
PW, M6 (A) PW, M6 (A)(Option) PW, M6 (A)(Stainless Steel Model) PW, M6 (A)(Stainless Steel Model)(Option)

31 WD25450170 32 WD25450110

Wire Duct 25×45×170 Wire Duct 25×45×110 (Option)

34 T5-4-10580

Grommet Grommet (Option)

36 EW720106C003 Wire Ass’y

Q’TY Greenbridge PART # 22 191612 30 22 X 30
1 X 1 X
2 191803 4
1 X

-C106-

5-1-1

FOOT BAR ASS’Y

-C107-

5-1-1

FOOT BAR ASS’Y

Greenbridge PAPARRTT# # 191532 X
191533 X
191534 X

-C108-

5-1-1

FOOT BAR ASS’Y

REF. NO. 24
25
26
27

PART NO.
SW06 SW06S SW05 SW05S PW05 PW05S PW06C PW06CS

DESCRIPTION
SW, M6 SW, M6 (Stainless Steel Model) SW, M5 SW, M5 (Stainless Steel Model) PW, M5 PW, M5 (Stainless Steel Model) PW, M6 (C) PW, M6 (C)(Stainless Steel Model)

31 SR15 SR15S

Stop Ring, S-15 Stop Ring, S-15 (Stainless Steel Model)

Q’TY Greenbridge PART #
3 191562 3 205539 1 191577 1 X 1 191578 1 X 3 191561 3 205534
2 191804 2 X

-C109-

-C110-

5-2

COVER GROUP

M7-5-200111

M7-5-200121

-C111-

5-2

COVER GROUP

Greenbridge PAPARRTT# # X X
X X
X X
X X
X X

-C112-

5-2

COVER GROUP

REF. NO.

PART NO.

8 M7-5-202500

10 M7-5-202200 11 M7-5-210021
M7-5-210021S

12 M7-5-220021 M7-5-220021S

M7-5-220031 M7-5-220031S

M7-5-220061 M7-5-220061S

M7-5-220091 M7-5-220091S

13 M7-5-230021 M7-5-230021S

M7-5-230031

M7-5-230031S

M7-5-230041 M7-5-230041S

M7-5-230051

M7-5-230051S

M7-5-230061 M7-5-230061S

M7-5-230071

M7-5-230071S

M7-5-230081 M7-5-230081S

DESCRIPTION Bracket (Option)

Q’TY Greenbridge PART # 1 191607

Guide LH Plate (For 1050W/1650W) Upper Table Front Ass’y (For 650W) Upper Table Front Ass’y (Stainless Steel

1 X 1 (SEE PG. C117) X 1 X

Model)(For 650W)

Upper Table Front Ass’y (For 850W) Upper Table Front Ass’y (Stainless Steel

1 (SEE PG.C119) 191645 1 X

Model)(For 850W)

Upper Table Front Ass’y (For 1050W)

1 X

Upper Table Front Ass’y (Stainless Steel

1 X

Model)(For 1050W)

Upper Table Front Ass’y (For 1250W)

1 X

Upper Table Front Ass’y (Stainless Steel

1 X

Model)(For 1250W)

Upper Table Front Ass’y (For 1650W)

1 X

Upper Table Front Ass’y (Stainless Steel

1 X

Model)(For 1650W)

Upper Table Rear Ass’y (For 850W) Upper Table Rear Ass’y (Stainless Steel Model)

1 1

(SEE PG.C123) 191761 X

(For 850W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 850W)(Option) Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 850W)(Option)

Upper Table Rear Ass’y (For 1050W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X (For 1050W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 1050W)(Option)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 1050W)(Option)

Upper Table Rear Ass’y (For 1250W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 1250W) Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 1250W)(Option)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 1250W)(Option)

Upper Table Rear Ass’y (For 1650W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 1650W)

-C113-

5-2

COVER GROUP

Greenbridge PAPARRTT# #

X 191686 X
-C114-

5-2

COVER GROUP

REF. NO.

PART NO.

44 SW05

45 SW06

47 PW05
48 PW05S 49 PW06A
51 NTE05

DESCRIPTION
SW, M5 (For 650W/850W/1250W) SW, M5 (For 1050W/1650W) SW, M6 (For 650W~1050W) SW, M6 (For 1250W/1650W)
PW, M5 (For 650W/850W/1250W) PW, M5 (For 1050W/1650W) PW, M5 (Stainless Steel Model) PW, M6 (A)
NTE, M5

57 EW720006C002 Wire Ass’y (For 650W) EW720008D002 Wire Ass’y (For 850W/1050W) EW720016C002 Wire Ass’y (For 1250W/1650W)

Q’TY Greenbridge PART # 8 191577 10 2 191562 4
10 191578 12 4 X 2 191612
8 191076
1 X 1 X 1 X

-C115-

-C116-

5-2-1

UPPER TABLE FRONT ASS’Y M7-5-210021 (For 650W)

-C117-

5-2-1 (For 650W)

UPPER TABLE FRONT ASS’Y

M7-5-210021
Greenbridge PAPARRTT# #

X

-C118-

5-2-2

UPPER TABLE FRONT ASS’Y M7-5-220021

(For 850W–1650W)

M7-5-220031

I

I I

……
N

-C119-

5-2-2

REF. NO.

PART NO.
M7-5-220021 M7-5-220021S

M7-5-220031 M7-5-220031S

M7-5-220061 M7-5-220061S

M7-5-220091 M7-5-220091S

1 M7-5-221121 M7-5-221121S

M7-5-221131 M7-5-221131S

M7-5-221161 M7-5-221161S

M7-5-221191 M7-5-221191S

3 M7-5-211301 M7-5-211301S
4 M7-5-211400

UPPER TABLE FRONT ASS’Y (For 850W~1650W)

DESCRIPTION
Upper Table Front Ass’y (For 850W) Upper Table Front Ass’y (Stainless Steel Model)(For 850W) Upper Table Front Ass’y (For 1050W) Upper Table Front Ass’y (Stainless Steel Model)(For 1050W) Upper Table Front Ass’y (For 1250W) Upper Table Front Ass’y (Stainless Steel Model)(For 1250W) Upper Table Front Ass’y (For 1650W) Upper Table Front Ass’y (Stainless Steel Model)(For 1650W) Upper Table Front (For 850W) Upper Table Front (Stainless Steel Model) (For 850W) Upper Table Front (For 1050W) Upper Table Front (Stainless Steel Model) (For 1050W) Upper Table Front (For 1250W) Upper Table Front (Stainless Steel Model) (For 1250W) Upper Table Front (For 1650W) Upper Table Front (Stainless Steel Model) (For 1650W)

Q’TY Greenbridge PART # 1 191645 1 X
1 X 1 X
1 X 1 X
1 X 1 X
1 191646 1 X
1 X 1 X
1 X 1 X
1 X 1 X

Shaft Shaft (Stainless Steel Model) Bracket

2 191678 2 191509 1 191552

9 T6-5-11120 T6-5-11121

Table Roller (250mm)(For 850W) Table Roller (250mm)(For 1050W) Table Roller (250mm)(For 1250W/1650W) Table Roller (250mm)(Stainless Steel Model) (For 850W) Table Roller (250mm)(Stainless Steel Model) (For 1050W) Table Roller (250mm)(Stainless Steel Model) (For 1250W/1650W)

6 191673 4 8 6 X
4
8

-C120-

5-2-2

UPPER TABLE FRONT ASS’Y (For 850W~1650W)

Greenbridge PAPARRTT# #

X
191559 203312

-C121-

-C122-

5-2-3

UPPER TABLE REAR ASS’Y (For 850W–1650W)

M7-5-230021 M7-5-230031

-C123-

5-2-3

REF. NO.

PART NO.
M7-5-230021 M7-5-230021S

M7-5-230031

M7-5-230031S

M7-5-230041 M7-5-230041S

M7-5-230051

M7-5-230051S

M7-5-230061 M7-5-230061S

M7-5-230071

M7-5-230071S

M7-5-230081 M7-5-230081S

M7-5-230091

M7-5-230091S

1 M7-5-231121 M7-5-231121S

M7-5-231131

M7-5-231131S

M7-5-231141 M7-5-231141S

M7-5-231151

M7-5-231151S

UPPER TABLE REAR ASS’Y (For 850W~1650W)

DESCRIPTION

Q’TY Greenbridge PART #

Upper Table Rear Ass’y (For 850W)

1 191761

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 850W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 850W)(Option)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 850W)(Option)

Upper Table Rear Ass’y (For 1050W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 1050W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 1050W)(Option)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 1050W)(Option)

Upper Table Rear Ass’y (For 1250W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 1250W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 1250W)(Option)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 1250W)(Option)

Upper Table Rear Ass’y (For 1650W)

1 X

Upper Table Rear Ass’y (Stainless Steel Model) 1 X

(For 1650W)

Upper Table Rear Ass’y (For Photo Eye)

1 X

(For 1650W)(Option) Upper Table Rear Ass’y (For Photo Eye)

1 X

(Stainless Steel Model)(For 1650W)(Option)

Upper Table Rear (For 850W) Upper Table Rear (Stainless Steel Model)

1 X 1 X

(For 850W) Upper Table Rear (For Photo Eye)(For 850W)

1 X

(Option)

Upper Table Rear (For Photo Eye)

1 X

(Stainless Steel Model)(For 850W)(Option)

Upper Table Rear (For 1050W)

1 X

Upper Table Rear (Stainless Steel Model)

1X

(For 1050W)

Upper Table Rear (For Photo Eye)(For 1050W) 1 X

(Option)

Upper Table Rear (For Photo Eye)

1 X

(Stainless Steel Model)(For 1050W)(Option)

-C124-

5-2-3

REF. NO.

PART NO.
M7-5-231161 M7-5-231161S

M7-5-231171

M7-5-231171S

M7-5-231181 M7-5-231181S

M7-5-231191

M7-5-231191S

UPPER TABLE REAR ASS’Y (For 850W~1650W)

DESCRIPTION

Q’TY Greenbridge PART #

Upper Table Rear (For 1250W) Upper Table Rear (Stainless Steel Model) (For 1250W) Upper Table Rear (For Photo Eye)(For 1250W) (Option) Upper Table Rear (For Photo Eye) (Stainless Steel Model)(For 1250W)(Option) Upper Table Rear (For 1650W) Upper Table Rear (Stainless Steel Model) (For 1650W) Upper Table Rear (For Photo Eye)(For 1650W) (Option) Upper Table Rear (For Photo Eye) (Stainless Steel Model)(For 1650W)(Option)

1 X 1 X 1 X
1 X 1 X 1 X
1 X 1 X

5 M7-6-102100 M7-6-102100S
6 T6-5-11120 T6-5-11121
7 T6-5-11130 T6-5-11131
8 T7-5-40410 T7-5-40411

Handle (Option) Handle (Stainless Steel Model)(Option) Table Roller (250mm)(For 850W) Table Roller (250mm)(For 1050W) Table Roller (250mm)(For 1250W/1650W) Table Roller (250mm)(Stainless Steel Model) (For 850W) Table Roller (250mm)(Stainless Steel Model) (For 1050W) Table Roller (250mm)(Stainless Steel Model) (For 1250W/1650W) Table Roller Shaft (For 850W) Table Roller Shaft (For 1050W) Table Roller Shaft (For 1250W/1650W) Table Roller Shaft (Stainless Steel Model) (For 850W) Table Roller Shaft (Stainless Steel Model) (For 1050W) Table Roller Shaft (Stainless Steel Model) (For 1250W/1650W) Table Roller (130mm)(For 1050W) Table Roller (130mm)(For 1250W/1650W) Table Roller (130mm)(Stainless Steel Model) (For 1050W) Table Roller (130mm)(Stainless Steel Model) (For 1250W/1650W)

1 191606 1 X 5 191673 4 7 5 X
4
7
5 191674 4 7 5 X
4
7
3 191751 1 3 X
1

-C125-

5-2-3

REF. NO.

PART NO.

9 T7-5-40420

T7-5-40420S

UPPER TABLE REAR ASS’Y (For 850W~1650W)

DESCRIPTION
Table Roller Shaft (For 1050W) Table Roller Shaft (For 1250W/1650W) Table Roller Shaft (Stainless Steel Model) (For 1050W) Table Roller Shaft (Stainless Steel Model) (For 1250W/1650W)

Q’TY Greenbridge PART # 3 191752 1 3 X
1

16 ER07 ER07S
21 TMS0512 TMS0512S
26 SW05 SW05S

Snap Ring, E-7 (For 850W) Snap Ring, E-7 (For 1050W) Snap Ring, E-7 (For 1250W/1650W) Snap Ring, E-7 (Stainless Steel Model) (For 850W) Snap Ring, E-7 (Stainless Steel Model) (For 1050W) Snap Ring, E-7 (Stainless Steel Model) (For 1250W/1650W)

10 191649 14 16 10 203502
14
16

TMS, M5×12 (Option) TMS, M5×12 (Stainless Steel Model)(Option)
SW, M5 (Option) SW, M5 (Stainless Steel Model)(Option)

2 191580 2 X 2 191577 2 X

-C126-

5-3

EXTENSION TABLE GROUP M7-5-300041

(For 1050W/1650W)

M7-5-300051

-C127-

5-3

REF. NO.

PART NO.
M7-5-300041 M7-5-300041S

M7-5-300051 M7-5-300051S

1 M7-5-301101 M7-5-301101S

M7-5-301111 M7-5-301111S

2 M7-5-301200 M7-5-301200S

3 M7-5-301300 M7-5-301300S

4 M7-5-301421 M7-5-301421S

5 M7-5-301501 M7-5-301501S

EXTENSION TABLE GROUP (For 1050W/1650W)

DESCRIPTION

Q’TY Greenbridge PART #

Extension Table Group (For 1050W) Extension Table Group (Stainless Steel Model) (For 1050W) Extension Table Group (For 1650W) Extension Table Group (Stainless Steel Model) (For 1650W) Extension Table (For 1050W) Extension Table (Stainless Steel Model) (For 1050W) Extension Table (For 1650W) Extension Table (Stainless Steel Model) (For 1650W) Rack (Right)(Only 1650W) Rack (Right)(Stainless Steel Model) (Only 1650W) Rack (Left)(Only 1650W) Rack (Left)(Stainless Steel Model) (Only 1650W) Upper Table Front (Only 1050W) Upper Table Front (Stainless Steel Model) (Only 1050W) Upper Table Rear (Only 1050W) Upper Table Rear (Stainless Steel Model) (Only 1050W)

1 X 1 X

1 X 1 X

1 1

X X

1 X 1 X

1 X 1 X

1 X 1 X

1 X 1 X

1 X 1 X

11 M7-5-310021 M7-5-310021S
12 M7-5-320001 M7-5-320001S

Upper Table Front Ass’y (Only 1650W) Upper Table Front Ass’y (Stainless Steel Model)(Only 1650W) Upper Table Rear Ass’y (Only 1650W) Upper Table Rear Ass’y (Stainless Steel Model)(Only 1650W)

16 M7-5-201600 M7-5-201600S
17 T7-2-10280
23 HBS0616N
24 HBS0616S

Cover Cover (Stainless Steel Model) Block
HBS, M6×16 (N)(For 1050W) HBS, M6×16 (N)(For 1650W) HBS, M6×16 (Stainless Steel Model) (Only 1650W)

-C128-

1 (SEE PG.C131) X 1 X
1 (SEE PG. C133) X 1 X

1 X

1 1

X X

6 191544 14 8 204086

5-3

EXTENSION TABLE GROUP

(For 1050W/1650W)

Greenbridge PAPARRTT# #

191686 191581

-C129-

-C130-

5-3-1

UPPER TABLE FRONT ASS’Y M7-5-310021 (For 1650W)

-C131-

5-3-1 (For 1650W)

REF. NO.

PART NO.
M7-5-310021 M7-5-310021S

1 M7-5-311121 M7-5-311121S

UPPER TABLE FRONT ASS’Y

M7-5-310021

DESCRIPTION
Upper Table Front Ass’y (For 1650W) Upper Table Front Ass’y (Stainless Steel Model)(For 1650W) Upper Table Front Upper Table Front (Stainless Steel Model)

Q’TY Greenbridge PART # 1 X 1 X
1 X 1 X

6 T7-5-40410 T7-5-40411
7 T7-5-40420 T7-5-40420S

Table Roller (130mm) Table Roller (130mm)(Stainless Steel Model) Table Roller Shaft Table Roller Shaft (Stainless Steel Model)

2 191751 2 X
2 191752 2 X

11 ER07 ER07S

Snap Ring, E-7 Snap Ring, E-7 (Stainless Steel Model)

4 191649 4 203502

-C132-

5-3-2

UPPER TABLE REAR ASS’Y (For 1650W)

M7-5-320001

-C133-

5-3-2

REF. NO.

PART NO.
M7-5-320001 M7-5-320001S

1 M7-5-321101 M7-5-321101S

UPPER TABLE REAR ASS’Y (For 1650W)

M7-5-320001

DESCRIPTION
Upper Table Rear Ass’y (For 1650W) Upper Table Rear Ass’y (Stainless Steel Model)(For 1650W) Upper Table Rear Upper Table Rear (Stainless Steel Model)

Q’TY Greenbridge PART # 1 X 1 X
1 X 1 X

6 T7-5-40410 T7-5-40411
7 T7-5-40420 T7-5-40420S

Table Roller (130mm) Table Roller (130mm)(Stainless Steel Model) Table Roller Shaft Table Roller Shaft (Stainless Steel Model)

2 191751

2 X

2 2

191752 X

11 ER07 ER07S

Snap Ring, E-7 Snap Ring, E-7 (Stainless Steel Model)

4 191649 4 203502

-C134-

5-4

PEDAL CONTROL SET

T7-6-40001

(OPTION)

-C135-

5-4

REF. NO.
1 2

PART NO.
T6-6-10350 T7-5-20130

PEDAL CONTROL SET (OPTION)
DESCRIPTION Connector (Foot Switch) Micro Switch

T7-6-40001
Q’TY Greenbridge PART # 1 191530 1 X

6 TMS0308 TMS0308S

TMS, M3×8 TMS, M3×8 (Stainless Steel Model)

4 191719 4 X

-C136-

6

ELECTRIC CONTROL UNIT M7-6-900022

M7-6-900032

-C137-

ELECTRIC CONTROL UNIT

REF. NO.

PART NO.
M7-6-900022 M7-6-900022S

M7-6-900032 M7-6-900032S

M7-6-900082

M7-6-900082S

M7-6-900092

M7-6-900092S

M7-6-900102

M7-6-900102S

M7-6-900112

M7-6-900112S

1 M7-6-100040 M7-6-100040S

M7-6-100120

M7-6-100120S

M7-6-100130

M7-6-100130S

M7-6-100060 M7-6-100060S

M7-6-100150

M7-6-100150S

DESCRIPTION

Q’TY Greenbridge PART #

Electric Control Unit (For 220V~ 240V, 650W) Electric Control Unit (Stainless Steel Model) (For 220V~ 240V, 650W) Electric Control Unit (For 110V, 650W) Electric Control Unit (Stainless Steel Model) (For 110V, 650W) Electric Control Unit (For 220V~ 240V, 850W/1050W) Electric Control Unit (Stainless Steel Model) (For 220V~ 240V, 850W/1050W) Electric Control Unit (For 110V, 850W/1050W) Electric Control Unit (Stainless Steel Model) (For 110V, 850W/1050W) Electric Control Unit (For 220V~ 240V, 1250W/1650W) Electric Control Unit (Stainless Steel Model) (For 220V~ 240V, 1250W/1650W) Electric Control Unit (For 110V, 1250W/1650W) Electric Control Unit (Stainless Steel Model)(For 110V, 1250W/1650W) Control Panel Group (Europe)(For 650W) Control Panel Group (Stainless Steel Model) (Europe)(For 650W) Control Panel Group (Europe) (For 850W/1050W) Control Panel Group (Stainless Steel Model) (Europe)(For 850W/1050W) Control Panel Group (Europe) (For 1250W/1650W) Control Panel Group (Stainless Steel Model) (Europe)(For 1250W/1650W) Control Panel Group (America)(For 650W) Control Panel Group (Stainless Steel Model) (America)(For 650W) Control Panel Group (America) (For 850W/1050W) Control Panel Group (Stainless Steel Model) (America)(For 850W/1050W)

1 X 1 X 1 X 1 X
1 X
1 X
1 X 1 X 1 X 1 X 1 X
1 X 1 SEE PAGE C141 X 1 X
1 X 1 X 1 X
1 X 1 X 1 X 1 X
1 X

-C138-

ELECTRIC CONTROL UNIT

REF. NO.

PART NO.

M7-6-100160

M7-6-100160S

2 M7-6-200002

M7-6-200002S

M7-6-200012

M7-6-200012S

3 M7-6-300111 M7-6-300121 M7-6-300131
4 M7-6-400000

M7-6-400020

M7-6-400030

DESCRIPTION
Control Panel Group (America) (For 1250W/1650W) Control Panel Group (Stainless Steel Model) (America)(For 1250W/1650W) Electric Control Group (Without Wire) (For 220V~240V) Electric Control Group (Without Wire) (Stainless Steel Model)(For 220V~240V) Electric Control Group (Without Wire) (For 110V) Electric Control Group (Without Wire) (Stainless Steel Model)(For 110V) Wires Group (For 650W) Wires Group (For 850W/1050W) Wires Group (For 1250W/1650W) Photo Eye Timer Box Group (For 650W) (Option) Photo Eye Timer Box Group (For 850W/1050W)(Option) Photo Eye Timer Box Group (For 1250W/1650W)(Option)

Q’TY Greenbridge PART # 1 X
1 X
1 SEE PAGE C145 X
1 X 1 X
1 X
1 SEE PAGE C149 X 1 X 1 X 1 SEE PAGE C154 X 1 X 1 X

-C139-

-C140-

6-1

CONTROL PANEL GROUP

-C141-

6-1

CONTROL PANEL GROUP

REF. NO.

PART NO.
M7-6-100040 M7-6-100040S

M7-6-100120

M7-6-100120S

M7-6-100130

M7-6-100130S

M7-6-100060 M7-6-100060S

M7-6-100150

M7-6-100150S

M7-6-100160

M7-6-100160S

1 M7-6-101101 2 M7-6-101201 3 M7-6-101300 4 M7-6-101400 5 M7-6-101501 6 M7-6-101601 7 M7-6-101701 8 M7-6-101800 9 TT-5-20120
T5-4-10324

11 M7-6-102100 M7-6-102100S
12 M7-6-102200 13 LA-10191 14 EW720006C004
EW720008D004 EW720016C004 15 M7-6-100100 M7-6-100100S 16 M7-6-102001

DESCRIPTION
Control Panel Group (Europe)(For 650W) Control Panel Group (Stainless Steel Model) (Europe)(For 650W) Control Panel Group (Europe) (For 850W/1050W) Control Panel Group (Stainless Steel Model) (Europe)(For 850W/1050W) Control Panel Group (Europe) (For 1250W/1650W) Control Panel Group (Stainless Steel Model) (Europe)(For 1250W/1650W) Control Panel Group (America)(For 650W) Control Panel Group (Stainless Steel Model) (America)(For 650W) Control Panel Group (America) (For 850W/1050W) Control Panel Group (Stainless Steel Model) (America)(For 850W/1050W) Control Panel Group (America) (For 1250W/1650W) Control Panel Group (Stainless Steel Model) (America)(For 1250W/1650W) Control Box Control Plate Rubber LCD Bracket Encoder Knob Flex-Protection Cable Gland Power Cord (Europe) Power Cord (America)
Handle Handle (Stainless Steel Model) Hinges Label Wire Ass’y (For 650W) Wire Ass’y (For 850W/1050W) Wire Ass’y (For 1250W/1650W) Control Panel Ass’y Control Panel Ass’y (Stainless Steel Model) Magnet Catch

Q’TY Greenbridge PART #
1 X 1 X

1 X

1 X

1 X

1 X

1 X 1 X

1 X

1 X

1 X

1 X

1 204750

1 204751

2 X

1 191513

2 1 1 1

X 191484 191510 204693 X

1 191518

1 191518

1 191606 1 X 2 191572 1 X 1 X 1 X 1 X
1 203016 1 X 2 X

-C142-

6-1

CONTROL PANEL GROUP

REF. NO. 17 18 19 20 21
22

PART NO.
T5-4-10222 T5-4-10232 T6-6-40016 T7-6-20480 T6-6-10320 T6-6-10980

24 PMS0408 25 PMS0430
PMS0430S 26 TMS0308 27 TMS0312

29 FHS0416S 30 FMS0508N
FMS0508S 31 SW03 32 SW05 33 SW04
SW04S 36 PW05

DESCRIPTION
Knob (Hole 6.0) Variable Resistor (5K)(6.0) 2P. Selector Switch Restart Switch (2NO) Heater Terminal Cable Gland (PG11)
PMS, M4×8 PMS, M4×30 PMS, M4×30 (Stainless Steel Model) TMS, M3×8 TMS, M3×12
FHS, M4×16 (SUS) FMS, M5×8 (N) FMS, M5×8 (Stainless Steel Model) SW, M3 SW, M5 SW, M4 SW, M4 (Stainless Steel Model) PW, M5

Q’TY Greenbridge PART #
1 191519 1 191539 1 191520 1 191494 1 X 2 X
2 X 4 X 4 X 1 191719 1 X
2 X 8 191702 8 191722 2 191590 2 191577 4 X 4 X 2 191577

41 NTE04 42 HN05
46 HBS0512N

NTE, M4 HN, M5
HBS, M5×12 (N)

2 X 4 187478
2 190848

-C143-

-C144-

6-2

ELECTRIC CONTROL GROUP M7-6-200002

-Cl45-

6-2
PART

ELECTRIC CONTROL GROUP
Greenbridge PAPARRTT# # X X
X X
X X X X

TT
X X X X X
-C146-

6-2

ELECTRIC CONTROL GROUP

Greenbridge PAPARRTT# # X X

190848 X X

-C147-

-C148-

6-3

WIRES GROUP

M7-6-300111

-C149-

6-3

WIRES GROUP

M7-6-300111

M7-6-300121

(1 OF 2)

Greenbridge PPAARRTT# #
X X X

-C150-

6-3

WIRES GROUP

M7-6-300111

M7-6-300121

(2 OF 2)

-C151-

6-3

WIRES GROUP

REF. NO.
1 2

PART NO.
EW720005BM04 EW720006CM01

DESCRIPTION
Wire Ass’y X4 (Power for M4/M5 PCB) Wire Ass’y X1 (Power for M4/M5)

M7-6-300111 M7-6-300121
(2 OF 2)
Q’TY Greenbridge PART # 1 X 1 X

6 EW720005BH02 Wire Ass’y X2 (Power for H.T PCB) 7 EW720005BH01 Wire Ass’y X1 (H.T/Sensor/Fan) 8 EW720005BH03 Wire Ass’y X3 (Heater Ready)

1 X 1 X 1 X

-C152-

6-4

PHOTO EYE TIMER BOX GROUP

(OPTION)

-C153-

6-4

REF. NO.

PART NO.

M7-6-400000

M7-6-400020

M7-6-400030

1 M7-6-401100 2 M7-6-401200

PHOTO EYE TIMER BOX GROUP (OPTION)

DESCRIPTION
Photo Eye Timer Box Group (For 650W) (Option) Photo Eye Timer Box Group (For 850W/1050W)(Option) Photo Eye Timer Box Group (For 1250W/1650W)(Option) Box P.C. Board

Q’TY Greenbridge PART # 1 X
1 X
1 X
1 X 1 X

6 EW720005B006 Wire Ass’y (For 650W) EW720008D006 Wire Ass’y (For 850W/1050W) EW720016C006 Wire Ass’y (For 1250W/1650W)

1 202738 1 X 1 X

11 M7-6-400100
14 M7-6-301200
16 T5-4-10222 17 T5-4-10232 18 T6-6-10570

Photo Eye Timer Box Ass’y
Photo Eye (PH1)
Knob (Hole 6.0) Variable Resistor (5K)(6.0) 3P. Selector Switch

21 LA-20050

Label

24 PMS0305 25 PMS0345

PMS, M3×5 PMS, M3×45

1 191707 1 (SEE PG. C3) 191827 2 191519 2 101539 1 205070
1 X
2 X 4 X

-C154-

06/2017

References

• Greenbridge | Strapping Solutions, Tools & Equipment

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>