GREENBRIDGE B2000 Battery Powered Friction Weld Tool User Manual

GREENBRIDGE B2000 Battery Powered Friction Weld Tool

SAFETY INSTRUCTIONS

READ THE OPERATING INSTRUCTION CAREFULLY

| WHEN OPERATING THE TOOL, WEAR EYE AND HAND SAFETY PROTECTORS AND SAFETY SHOE
---|---

GENERAL SAFETY INSTRUCTIONS

The tool must not be used by people not properly trained. Failure to follow the operating instructions or improper use could cause strap breakage, injuries, package damages. Check tool daily, do not use tool with worn or damaged parts, promptly replace them by trained people and use original spare parts. Never modify any tool part. Do not put fingers, hands or other body parts between the strap and package during the cycle. It is your full responsibility to check the joints made by your tool, seal control and a suitable training about adjustment will be useful to check the seal quality in order to avoid severe injury. Never move goods with bad quality seals. Use only specific strap dispenser to dispense the strap. Keep tidy your working area and always use the tool in good balance and safety conditions. Never use straps as a means of pulling or lifting goods. To cut the straps use always proper safety strap cutter and keep other people and yourself at safe distance from strap, always stand to side of strap, away from direction of strap trajectory once loosen. Hold the upper strap portion and pay attention that the lower strap will snap forward away from you. Improper operation, excessive tensioning, use of not recommended strap, sharp corners on the package could cause in a sudden loss of strap tension and/or strap breakage that could lead to package fall and to violent movement of the strap against the operator. It is recommended to use edge protectors if package has sharp corners, to place the strap correctly around a properly positioned package, to remain in safety position (on one side of strap) during strapping cycle, to use the correct strap quality, width, thickness, and strength as recommended in this manual. Please preserve this booklet, it is as a part of the tool. This tol is manufactured without any substances which could be dangerous to health. National instructions must be observed for disposal of all the parts.

DISPOSAL INFORMATION

The legal regulations for disposal of all tool parts must be observed. Please dismantled the electrical parts from mechanical parts so can be disposed separately. The battery and charger must be collected, recycled or disposed of in an environmentally friendly way. Don’t throw into waste

TECHNICAL DATA

DIMENSIONS

Length:| 300 mm – 11.8”
Width:| 150 mm – 5.9”
Height:| 200 mm – 7.9”
Weight with battery:| 6.4 kgs – 14.2 lbs
FEED REQUIRE.
Battery| 36V – 2 A/h Li-Ion
PERFORMANCES

Max.Tension :| 8000 N
Min. Tension| 2700 N
Tensioning speed:| 12 mt/m
Sealing:| Saldatura vibrazione
Joint strength approx.:| **75% carico di rottura ***
Level sound emission. Measurement type A (2003/10/CE)|

81 dB (A)

Vibrations at handle (2002/44/CE)| 2.2 ms 2

• variabile in funzione del tipo di reggia

Working temperature: the tool should be used between 0C° ( 32F) and +45C° (+113 F). With the use to low temperature it may happen that the display signals low battery. In this case it suffices to insert the battery for 2 mins. in charger for a “refreshing”

CHART OF TYPES

1.4 mm (0.031”  ÷ 0.041”)
1 mm ÷ 1.30 mm (0.031”  ÷ 0.050”)

WARRANTY CONDITIONS AND LIABILITY

Greenbridge warrants all its tools and battery chargers during a period of 6 months from the shipping date document. Wear parts are warranted for 45 days, otherwise wear parts are excluded from regular warranty, wear parts are shown on spare parts list (in tool manual).

Warranty includes free replacement parts. The warranty is not valid in case of improper use, lack of maintenance, tampering, arbitrary modifications and reparations, use of non-original parts, disregard of instructions of the operation manual, or missing serial number. No compensation can be claimed for production shutdowns and for damages to people and objects due to tool defects. Greenbridge reserves the right to modify the tools and documentation without any obligation to update previous ones.

Greenbridge warrants all its batteries during a period of 120 days from the shipping date document. The manufacturer is committed to replace it with a free battery only when there are manufacturing defects that make it unfit for use.

INSTALLATION

BATTERY

SAFETY INSTRUCTIONS : To start working put the battery until you hear the click of the lock button, as shown in the image and press button 1. The battery should be used by people properly trained. Failure to follow the operating instructions or improper use could cause injuries and battery damages. The battery is supplied partially charged. The Lithium-Ion rechargeable battery can be charged at any time without reducing its service life; interrupting the charging procedure doesn’t damage it. To use and charge the battery please follow the operating devices instruction. Check battery daily, do not use it with worn or damaged parts. Do not disassemble it, never modify any part, do not connect the positive (+) and negative (-), may result a full damaging short circuit. Do not invert the right polarity during the use or charge. Do not transport or store the battery with metal objects, may result a short circuit. Do not try to charge with different charger not allowed, the battery could be seriously damaged. Before use check the contacts. Do not put metal keys between contacts. Do not use the battery for purposes other than those specified. Battery must not be left in charging mode without supervision. Do not throw the battery into a fire or heat it, do not store at high temperature, direct sunlight, do not put in microwave oven or a pressure cooker. Keep it away from any exposed flame. Do not dip the battery in the water, protect it from humidity. Do not apply impact to the battery, or throw , drop, drill it, if happened try it with care . In case of heat generation, smoke emission, or ignition stop immediately to use and replace it. In case electrolyte comes into contact with eyes, rinse thoroughly with clean water immediately and consult a physician; for hands contact use clean water too.

CONTROL BATTERY LEVEL : Pressing “on” button the state of charge will be displayed trough 3 led. If all the led is lightning the battery is fully charge. If only one led is lightning then shortly the battery needs to be recharged.

TECHNICAL DATA : Li-Ion (Lithium-Ion) 36V – 2 Ah Weight : 1100 gr Cod. B800477
Time of charging 40 min. Temperature charging and discharging : 0C° ( 32F) and +45C° (+113 F)

BATTERY CHARGER

SAFETY INSTRUCTIONS: : The charger must only be used by properly trained personnel. Do not follow the instructions in the manual and / or improper use can cause damage and danger to personnel. Charge only rechargeable batteries for Bosch lithium ion or rechargeable batteries installed in Bosch products with the voltages indicated in the specifications. Daily check the device and the power cord, do not use if damaged. Do not disassemble or modify the charger, do not connect to each other contacts, creating a short circuit that would irreparably damage the electronic circuit. Do not reverse the polarity when using or recharging.
Before use, check that the contacts are clean, intact and there is no metal objects in the battery case. DO NOT LEAVE IN
C HARGE BATTERY WITHOUT SUPERVISION. Do not place near heat sources, do not leave it exposed to the sun. Do not cover the ventilation slits. Protect it from moisture, do not immerse in water and do not let any liquid drip. Avoid shocks, falls, fractures, should try it with caution, if it produces heat, smoke, etc., do not use it. The battery charger must be placed in a stable manner on a flat surface, non-flammable and heat resistant. Keep away from the charging area every type of flammable or volatile substance. Always unplug the appliance from the mains when not in use. Any action contact qualified personnel or an authorized service center.

CHARGING PROCESS: The fast charging operation is indicated by the flashing charge indicator of battery green. The battery can be taken out and used at any time. Note: The charging operation is possible only when the temperature of the rechargeable battery is located within the range of allowable charging temperature. Once reached 80% of the battery capacity, the indicator flashes frequency slows. At this point ends the rapid charging process. If the battery is inserted into the charger the charging process is completed in a mode Long Life.
The continuous charge indicator of the battery green, indicates that the battery is fully charged.
Once finished, the battery can be pulled out and is ready for immediate use.
When the rechargeable battery is not inserted, the continuous charge indicator of the battery green indicates that the plug is connected to the network and inserted into the power outlet and the charging station and ready for operation.

MALFUNCTION: The fixed charge indicator of the battery red indicates that the temperature of the Battery is outside the allowed range. As soon as it reaches the permissible temperature range, begins charging process. The indicator flicker of battery red indicates another failure operation of charging. If when inserting the battery in the charging station and lit the red indicator for the temperature control on the battery, the battery temperature and outside the charging temperature range.

TECHNICAL DATA : Cod.B800483 230V / B800535 110V Power supply: from 14.4 V to 36 V Output: 8A
WARNING : The battery charger can only be used with battery Bosch Li-Ion

VISUAL SIGNAL

SOUND SIGNAL

LOADED – READY TO USE BUT STILL HOUSED INTO CHARGER
FAST INTERMITTENT CONTINUOUS BEEPS| BATTERY HAS TROUBLE – CHARGE DIDN’T ALLOW

ACCESSORIES

SUSPENSION HOOK

The tool could be equipped with a three positions suspension hook. The hook must be fix to the tool by two screw (included) in vertical or horizontal position.

OPERATING ELEMENTS AND ADJUSTMENTS

DO NOT OPERATE THE TOOL WITHOUT STRAP, YOU COULD DAMAGE THE FEEDWHEEL AND THE WELDING / CUTTING GROUP

LED OF SIGNALLING

GREEN| TOOL IN WORK
GREEN BLINKING| STAND-BY TOOL

REGOLAZIONE TENSIONAMENTO E SALDATURA / ADJUSTING TENSION AND WELDING

In order to do any kind of adjustment (welding / cutting and tensioning) first of all that the machine should be switch on, then press the adjust tension button as shown in picture A for about 3 sec., the number equal to the tension force will flash and after you can select the desired value. Once you release the button, the number will stop flashing after about 3 seconds and the set value will be stored. The same procedure must be done in order to set the welding value using the button as shown in picture B.

OPERATING MODE

Press and hold for 3 sec. the SET button to access the various modes of operation (automatic, semiautomatics and manual) Fig C. Iniziarà to flash the led corresponding to the mode in use, then you can select the one you want, when you release the button, the LED will stop blinking after about 3 seconds and the mode you set will be stored.
AUTOMATIC STRAPPING: The strapping is obtained by pressing twice within a short time key 1 retirement. Voltage, welding and cutting are automatic. To STOP the automatic tension press 1 or 2.
Warning: after 15 sec. the tension is automatically stopped if the maximum voltage is not reached
SEMI-AUTOMATIC STRAPPING: The strapping is achieved by holding down the 1 key of retirement, when the palace and pulled up to the set value is automatically sealed and cut. During the retirement stage if the button 1 is released the voltage stops.
STRAPPING MANUAL: The strapping is obtained by pressing the button 1, when the strap is tight enough to press the 2 key to welding and cutting.

STRAP SIZE CONVERSION

It’s possible to convert the unit for 19mm 5/8” – 25mm 1” – 32mm 1 1/4” strap sizes replacing front and lateral strap guide and moving the pin of the rear strap guide (25/32mm 1”/1 1/4”) or replace it (19mm 3/4”) as in the picture below

OPERATION

The tool model B2000 is designed to strap packages with plastic strap. The strap is fed around the package manually and
inserted in the tool, as showed in the instructions, tensioned, cutted and friction welded by the tool.
Wrap the parcel to be bound with the strap, as showed in pic.E1, holding the tip of the strap with left hand and winding over the strap by right hand ( beware that the strap will be clean, oil and grease free); to open the tool pressing the lever release, to insert very resists to them overlapping and aligned between the body and the base of the front and posterior apparatus pushing them against the strap. To press button 1 in order to carry out the tensioning until the attainment of the tension wished or set up (pic.E2).

(once caught up the maximum tension the machine allows to carry out others 3 tensionament after which the welding must happen) In order to carry out the welding to press button 2, the tool will carry out therefore the welding, the cut and the cooling of the strap (pic.E3). After the ignition of signalling led and the contemporary sound of the tool that indicate the end of the welding cycle it is possible to extract the strap **(pic.E4)

CONTROL BATTERY LEVEL : During use of the tool it’s possible to always view the charge status of the battery. Battery charging (pic.E5) – battery charge half (pic.E6) – Low Battery (pic.E7).** When the battery is about to run out of all the first led flash.

LOCKING AND RELEASE KEYS : The touch-pad lock can be activated to prevent accidental changes to the settings. Push every button twice, starting from SET button as in pic.E8, automatically the panel will lock and the letter L will appear that means “LOCK” (pic.E9). In this way the operator can not change any parameters. To unlock the panel repeat the procedure from the beginning.

CONTROLLO DELLA SALDATURA / SEAL CHECK

A regular seal quality control is very important and it could be exanimated visually as follow:

F1) short sealing time/ not enough

NO – seal strength insufficient

F2) right sealing time

Yes — right

F3) too long sealing time/ wrong

NO – seal strength affected

SERVICING – CLEANING

Clean periodically the tool from strap dusty, particular the feed wheel, the gripper plates and the cutter using exclusively compressed air

CLEANING AND REPLACEMENT FEEDWHEEL

To replace or clean the feedwheel, first remove the battery from the tool. Remove 4 cylinder screws B500035, remove the cover by turning it slightly, then remove the feed wheel from the gearbox and the ball bearing B400186 from the feedwheel.
To clean the tension roller use compressed air. Check the state of wear of the teeth before reinstalling it, if many teeth are worn replace it with a new one.To replace run in reverse order.

For cleaning or replacement of the strap locker proceed as follows: Remove the battery from the unit, remove the 2 screws
B500336 and remove the 2 washers B500211. Remove the strap locker from the front using pliers with long jaws. For cleaning of the plate, use compressed air. Check the state of wear of the teeth and then replace, if many teeth are worn replace it with a new one. To replace, run in reverse order.

WELDING FOOT AND WELDING PLATE REPLACEMENT

To replace the swinging leg and the welding plate proceed as follows: remove the battery from the tool. Remove the cover by screw, remove the pin D002020, remove welding foot D004540 with the help of a clamp and replace. To replace the welding plate repeat the previous steps, then through the socket of the welding foot, remove screw D001420, slide out with the help of a pair of pliers welding plate D004580. To replace, run in reverse order.

KNIFE REPLACEMENT

For replace the cutter proceed as follows: Remove the battery from the tool. Remove the cover by screw, remove the screw B500035, remove the cutter guide D002130 and finally remove the cutter and replace it with a new one. To replace, run in reverse order.

SERVO RESET

If due to some problem or if during welding operation the foot should remain lowered and prevent the extraction of the tool, remove and reinsert the battery. The servo will return in original position.

TROUBLESHOOTING

After battery fitting and pressing button 1 the tool doesn’t work

Check the battery contacts in the rear tool part and / or if there are disconnected wires Check the battery charge status
The tension of strap isn’t enough
Check the set tension on keypad
Check if the tension motor isn’t damaged or worn out Check the gearbox
Check the electronic card
The feed wheel slides
Check if the feedwheel or grippers aren’t dirty or damaged, adjust. Adjust the tension power.
The strap is breaking during tension
Adjust the tension force. Check if the strap qualities are right for the strapping tool and application. Pay attention at package cutting edges.
The tensioned strap is sideways bended; after fitting the strap the tool remaining open; the seal isn’t in the middle of strap width
Adjust the tension power. Check if the strap qualities are right for the strapping tool and application. Check strap size, adjust the guides. Check the alignment and if are worn out.
The tool goes forward during the tension
Check if the gripper isn’t dirty or damaged. Adjust the tension value as qualities of strap
Seizing signs on strap
Try to increase the gap. Check if the strap qualities are right for the strapping tool and application. Ambient temperature too high
After tensioning, the tool comes back after tensioning
Probably damaged the freewheel or the locking mechanism
The sealing isn’t enough; the upper strap isn’t completely cutted; the cutting isn’t constant
Check the sealing time, may be is too short, adjust it on keypad
Check if the sealing foot and / or the cutter aren’t damaged or worn out Check if the sealing foot isn’t dirty or slides on strap
Check if the tool come back after tensioning Check the battery charge / efficiency
Check if the strap qualities are right for the strapping tool and application Check if the sealing motor is worn out Check the electronic cards
During the sealing both straps are cutted
Check if the gripper plate (under the sealing foot) isn’t dirty or damaged (clean or replace it)

Check if the strap is too much tensioned. Improper weld timing adjustment, may be is too long, set it.

Pressing the weldin button doesn’t start the motor
Check if the welding button is damaged or disconnected.

Check if the sealing motor is worn out and the cables connected Check the electronic cards

After the duty cycle is not possible remove the tool and the opening lever is too hard to move
Check if the opening group is working or is locked (pull lightly the opening lever) Check the gearbox.
Check if there are some defected parts into the opening group and / or mechanical obstacles
Is difficult to adjust the work parameters, don’t remain constant or don’t set changing on keyboard
Probably there are keyboard or electronic card problems / try to replace it.
Progressive abatement of battery duty cycles
E Check the battery charge, try to recharge and check if the battery charger is running well. May be that the battery is going to recharge limit life
May be that the internal cells are damaged or worn out due to floor falls or strong impacts Try to have other trial with different battery
The charger will not start to recharge the battery
The battery is damaged. The battery tension is lower than 10V – check by electric tester Check if the charger is still running

SPARE PARTS LIST

Greenbridge PART NO.| CODE| DESCRIPTION| QTY.| |
---|---|---|---|---|---
206302| A000205| WELDING MOTOR ASSEMBLED| 1| |
206236| A000206| TENSION MOTOR ASSEMBLED| 1| |
206303| A000207| ECCENTRIC SHAFT ASSEMBLED| 1| |
206304| A000208| CONNECTING ROD ASSEMBLED| 1| |
206237| A000209| TENSION MOTOR FLANGE ASSEMBLED| 1| |
206305| A000210| SUPPORT FEEDWHEEL ASSEMBLED| 1| |
206306| A000211| SERVO/CAM CONNECTING LEVER| 1| |
| A000227| KIT GUIDE 19 mm| 1| |
189198| B400008| BEARING 6001 2RS ERI| 1| |
190028| B400188| BEARING INA HF0812| 1| |
206238| B400470| ROLL FLAT BEARING| 1| |
206239| B400471| BEARING 61903-2BRS| 1| |
206240| B400481| BEARING HK15/16| 1| |
190217| B400520| SERVO BEARING H61700-2Z| 1| |
189699| B500034| SCREW UNC 10×5/8″| 2| |
190031| B500035| CYLINDER SCREW M4x10 UNI5931| 2| |
190032| B500036| CYLINDER SCREW M5X12 UNI5931| 5| |
190196| B500037| CYLINDER SCREW M4x8 UNI5931| 10| |
189136| B500039| SCREW UNI 10-24×1/2”| 6| |
189698| B500047| SCREW STEI M5X8 UNI 5925| 1| |
190161| B500068| CYLINDER SCREW M3x8 UNI5931| 3| |
190147| B500211| WASHER| 8| |
190039| B500214| SCREW M4X8 UNI5933| 1| |
206307| B500274| SCREW M3x8 UNI5933| 4| |
190042| B500281| NUT M6 DIN985| 1| |
190043| B500336| SCREW Mx410 UNI5933| 4| |
190044| B500379| SCREW M4X5 UNI5932| 3| |
189578| B500394| SCREW M6x14 UNI5932| 4| |
190047| B500395| SCREW 3,5 X 16 KA35| 4| |
189785| B500407| SCREW UNC 1/4″X1/2″ ANSI B18.3| 8| |
189811| B500443| SCREW UNC1/4-20X3/4 18.3| 2| |
206241| B500463| WASHER| 10| |
190220| B500464| WASHER| 2| |
206242| B500488| SCREW TCEI M 2,5X10 UNI 20898| 1| |
206243| B500492| SCREW 3,5 X 35 KA35| 2| |
206244| B500493| CYLINDER SCREW M4x25 UNI5931| 2| |
190226| B500529| CHIPBOARD SCREW 3X20| 4| |
206245| B500546| CYLINDER SCREW M5X45 UNI5931| 1| |
190050| B600112| WASHER 12X18X0.5| 2| |
190052| B600159| CIRCLIP A12 DIN 471| 2| |
190054| B600190| CIRCLIP D8 TYPE E DIN 471| 2| |
190060| B600346| CIRCLIP D15 UNI 7435| 1| |
190227| B600402| CIRCLIP RA4 UNI7434 R150| 1| |
206246| B600484| SPRING G16-025 ISO10243| 1| |
206247| B600491| CIRCLIP RA6 DIN 6799 UNI 7977| 1| |
189750| B700075| PIN 3X10 DIN6325| 4| |
206248| B700474| PIN 5X36 UNI6325| 1| |
206249| B700487| PIN 4×18 ISO 8734| 1| |
190229| B700525| PIN 6×20 UNI6364B| 2| |
206250| B800472| ELETRONIC POWER CARD| 1| |
206252| B800477| BOSCH BATTERY 36V 2.0Ah| 1| |
190230| B800510| TENSION/WELDING BUTTON| 2| |
190205| B800515| KEYBOARD| 1| |
190204| B800531| ELETRONICS SIGNAL CARD| 1| |
190232| B800534| POWER CARD-KEYBOARD CONN. CABLE| 1| |
206251| B800551| SERVO MOTOR| 1| |
2000CHG| B800560| CHARGER 100-240V| 1| |
190071| D000170| GEAR SHAFT| 1| |
190074| D000330| LOCKING COVER| 1| |
190076| D000390| WASHER| 1| |
189132| D000620| SPRING| 1| |
190079| D001140| SPRING| 1| |
190081| D002020| WELDING FOOT PIN| 1| |
190087| D002080| PIN| 1| |
190091| D002130| CUTTER GUIDE| 2| |
190094| D002190| HOOK| 1| |
190101| D002270| ROLLER| 1| |
190105| D002310| SPRING| 2| |
190145| D004560| SPECIAL SCREW| 1| |
190242| D006270| PIN| 2| |
190249| D006390| FREE GEAR| 1| |
190251| D006410| OPENING LEVER| 1| |
190255| D006450| HANDLE| 1| |
190209| D006510| REAR STRAP GUIDE PIN| 1| |
204059| D006570| REAR GUIDE STRAP SPRING| 1| |
206254| D006590| HANDLE LOCKER| 1| |
206255| D006740| SPRING| 1| |
206258| D006780| WELDING FOOT| 1| §|
206259| D006790| *MOTOR SIDE WELDING FRAME| 1| |
206260| D006800| LEVER/HOOK SUPPORT| 1| |
206261| D006810| FRONT STRAP GUIDE 19mm| 1| |
206262| D006820| INTERNAL WELDING FRAME| 1| |
206263| D006850| WELDING FOOT| 1| |
206264| D006860| WELDING FOOT SUPPORT| 1| |
206265| D006870| SPRING SUPPORT| 1| |
206269| D006880| PIN CAM| 1| |
206270| D006890| WELDING PLATE| 1| §|
206271| D006900| CENTRAL PIN| 1| |
206272| D006920| SERVO LEVER| 1| |
206273| D006930| SPRING PIN| 1| |
206274| D006940| LATERAL STRAP GUIDE 19mm| 1| |
206275| D006950| HANDLE PLATE| 1| |
206276| D006960| GEARBOX| 1| |
206277| D006970| SPRING SUPPORT PIN| 1| |
206278| D006980| RIGHT COVER| 1| |
206279| D006990| LEFT COVER| 1| |
206280| D007000| BLADE COVER| 1| |
206281| D007010| RELEASE BATTERY LEVEL| 1| |
206282| D007020| BUFFER PROTECTION| 1| |
206283| D007030| SPECIAL SCREW WELDING PLATE| 1| |
206284| D007040| PIN CAM| 1| |
206285| D007060| CUTTER| 1| §|
206286| D007080| STRAPLOCKER| 1| §|
206287| D007090| LATERAL STRAP GUIDE 25mm| 1| |
206288| D007100| FRONT STRAP GUIDE 25mm| 1| |
206289| D007110| LATERAL STRAP GUIDE 32mm| 1| |
206290| D007120| REAR STRAP GUIDE 25/32mm| 1| |
206291| D007130| REAR STRAP GUIDE 19mm| 1| |
206292| D007180| FRONT FRAME| 1| |
206293| D007190| REAR STRAP GUIDE SUPPORT| 1| |
206294| D007220| FRONT STRAP GUIDE 32mm| 1| |
206295| D007230| SERVO SUPPORT| 1| |
206296| D007240| WELDING SUPPORT LOCKER SX| 1| |
206297| D007250| WELDING SUPPORT LOCKER DX| 1| |
206298| D007290| WELDING FOOT PIN| 1| |
206299| D007300| WELDING MOTOR FLANGE| 1| |
206300| D007320| SPRING WASHER| 1| |
206301| D007330| FEEDWHEEL| 1| §|
208396| D007370| FRONT FRAME| 1| |
208397| DOO7970| MAIN FRAME| 1| |

CE DECLARATION OF CONFORMITY

GREENBRIDGE Srl declares under own responsibility that the tool ITA 27, to which this declarations refers, is in conformity with 2006/42/CE Directive and successive modifications, as well as with standards EN12100-1, EN12100-2, EN60745-1, EN60745-2-18, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3
Batteries certificate to UN38.3 standard
Air Transportation Safety

Customer Support

6277 Heisley Road Mentor, Ohio 44060
Tel. 440-357-1500 Fax 440-352-9553 www.greenbridge.com

6277 HEISLEY ROAD, MENTOR, OHIO 44060
PHONE: 440.357.1500, FAX: 440.352.9553
WWW.GREENBRIDGE.COM

References

• Greenbridge | Strapping Solutions, Tools & Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>