SW-MOTECH STP.08.590.10900-B Mounting Kit For Frame Slider Instruction Manual
- May 15, 2024
- SW-MOTECH
Table of Contents
mounting instructions
STP.08.590.10900/B
STP.08.590.10900-B Mounting Kit For Frame Slider
Mounting kit for frame slider
The application list for this product can be found on our website.
Mounting Instructions
ATTENTION: The assembly of this product can be complicated and requires a
good technical understanding. If you are not sure of how to do this, have a
specialty garage perform the mounting and service. SW-MOTECH accepts no
liability for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW-
MOTECH, should be tightened to the torque specified in the OEM maintenance
manual for your motorcycle.
All screws, bolts and nuts should be checked after driving the first 50 km to
ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to
secure all screws, bolts and nuts.
Subject to change. Not responsible for typos.
Mounting
MOUNTING INSTRUCTIONS
Revision: 00 – Datum / Date: 10-2019
Crash pad set
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and POF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behaviour and/or stability of
your vehicle,
GENERAL INFORMATION
Observe the country-specific requlations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included, Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system, Use appropriate tools, Have another
person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW-MOTECH, Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle
manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and/or be pinched, Before starting to ride,
perform a comprehensive check of all functions. After the first 50 km and then
at regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
| Step | No. | Item No. / Description * | Part | Quantity | N.m** |
|---|---|---|---|---|---|
| 1 | 1 | STP.00.590.020L /R | Crash Pad; left / right | 2/2 | |
| 2 | 2 | STP.00.590.021 | Logo Insert | 2/2 | |
| 3 | 3 | 3,0 x 16 | Lenshead Screw, self-tapping | 2/2 | max.1,2 |
Mounting
Step [1]: Attach the crash pads (1) on both sides to the adapter plates of
your SW-MOTECH slider set for frame, as described in the mounting instructions
of the slider set for frame.
Step [2]: Place the logo inserts (2] on both sides into the crash pads…
Step [3]: … and attach them with the screws (3).
Tighten the screws (3) CAREFULLY by hand (max. 1,2 Nem)!
Copyright by
SW-MOTECH GmbH & Co. KG
Errors and omissions excepted. Technical and design modifications are subject
to change.
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10
35282 Rauschenberg
Germany
Tel. +49 (0) 64 25/8 16 8-050
Fax +49 (0) 64 25/8 16 8-10
info@sw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>