Planet Technology XT-715A 10GBASE-T To 10GBASE-X SFP+ Media Converter User Manual

Planet Technology XT-715A 10GBASE-T To 10GBASE-X SFP+ Media Converter

Specifications

• Model: XT-715A
• Conversion: 10GBASE-T to 10GBASE-X SFP+
• Revision: 1.0 (November, 2023)
• Part Number: EM-XT-715A_v1.0 (2351-AA5430-000)

FAQ

• Q: What should I do if I encounter connectivity issues with the XT-715A?
• A: If you experience connectivity problems, first ensure all cables are securely connected. You can also try power cycling the converter and checking network settings for compatibility.
• Q: Can I use third-party SFP+ transceivers with the XT-715A?
• A: It is recommended to use approved PLANET SFP+ transceivers for optimal performance and compatibility. Refer to the user manual for a list of approved transceivers.

Trademarks

• Copyright © PLANET Technology Corp. 2023
• Contents are subject to revision without prior notice.
• PLANET is a registered trademark of PLANET Technology Corp.
• All other trademarks belong to their respective owners.

Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this User’s Manual, and reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s Manual, at any time without notice.
If you find information in this manual incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

• PLANET 10GBASE-T to 10GBASE-X SFP+ Media Converter User’s Manual
• Model: XT-715A
• Revision: 1.0 (November, 2023)
• Part No: EM-XT-715A_v1.0 (2351-AA5430-000)

Introduction

Package Contents
Thank you for purchasing PLANET XT-715A 10GBASE-T to 10GBASE-X SFP+ Media Converter. In the following sections, unless specified, the term “Media Converter” mentioned in this manual refers to the XT-715A.
Open the box of the Media Converter and carefully unpack it. The box should contain the following items:

• If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
• The XT-715A comes with one vacant SFP module slot. The mini GBIC SFP module is not included in the package.

Product Features

Physical Port

• Media conversion between 2.5G/5G/10GBASE-T and 10GBASE-X SFP+ fiber optic
• Copper RJ45 port supports 2.5G/5G/10GBASE-T auto-negotiation and auto-MDI/MDI-X
• 10GBASE-X SFP+ Fiber Optic allows
• Multi-mode fiber using LC connector
• Single-mode fiber using LC connector

Layer 2 Features

• IEEE 802.3bz/an/ae Ethernet standard compliant
• Non-blocking full wire-speed forwarding rate
• IEEE 802.1Q tag-based VLAN transparency, multicast passthrough
• 16K jumbo frame
• IEEE 802.3x full-duplex and half-duplex back pressure flow control to eliminate the loss of packets

Mechanical

• Metal case
• LED indicators for easy network diagnostics
• 100 meters over Cat 6A/Cat 7 at 10Gbps RJ45 port
• External 5V DC, 2A power input socket
• Wall mounting or DIN-rail installation (optional)
• 0 to 50 degrees C operating temperature
• Compact in size, Plug and Play installation
• Best with PLANET’s 10”/19” Media Converter Chassis (MC-700/MC-1500/ MC-1500R/MC-1500R48)

Product Specifications

Interface
Copper Port| 2.5G/5G/10GBASE-T Ethernet RJ45 interface Auto-negotiation, auto MDI/MDI-X
SFP Interface| 10GBASE-X SFP+ interface
Fiber Mode| May vary on SFP Module
Fiber Port Type

(connector)

| SFP, LC type
Fiber Maximum

Distance

| May vary on SFP Module

Network Cables

| 2.5G/5G/10GBASE- T:

2.5G–Cat 5e/Cat 6/Cat 6A/Cat 7 5G–Cat 6/Cat 6A/Cat 7

10G–Cat 6A/Cat 7

Cat 5e/6/6A/7 UTP cable (100 meters, max.) EIA/TIA-568 100-ohm STP (100 meters.)

10GBASE- X:

50/125μm or 62.5/125μm multi-mode fiber optic

cable, up to 300m

9/125μm single-mode fiber optic cable, up to 80km

Hardware Specifications
Enclosure| Metal case
Dimensions

(W x D x H)

| 93.5 x 70 x 26 mm
Weight| 216g

LED

| System: PWR (Green)

10GBASE-X SFP+ Interface: Fiber LNK/ACT (Green)

10GBASE-T Ethernet Port: TP LNK/ACT (Green)

Power Supply| DC 5V, 2A Power Socket, external AC-to-DC adapter
Installation| Wall-mount or DIN-rail installation (Optional)
Layer 2 Features

Forwarding Rate| Non-blocking full wire-speed forwarding rate
Flow Control| Back pressure for half duplex mode

IEEE 802.3x pause frame for full duplex mode

Maximum Frame

Size

| 16K
Standards Conformance
Regulatory Compliance| FCC Part 15 Class A, CE

Protocols and Standards Compliance

| IEEE 802.3bz 2.5G/5GBASE-T

IEEE 802.3an 10GBASE-T

IEEE 802.3ae 10Gbps Ethernet IEEE 802.3x Flow Control

Environment
Temperature| Operating: 0 ~ 50 degrees C

Storage: -10 ~ 70 degrees C

Humidity| 5% ~ 95% non-condensing

Hardware Description

Physical Dimensions

• XT-715A dimensions (W x D x H): 93.5 x 70 x 26 mm

Converter Front Panel and LED Indicators

Figure 2-2 shows the front panel of the Media Converter

System

• 10GBASE-X SFP+ Interface

Fiber

|

Green

| Lights to indicate the link through that port is operating at 10Gbps.

• 10GBASE-T Ethernet Port

TP

|

Green

| Lights to indicate the link through that port is successfully established at 10Gbps.

Blinks to indicate that the 10G Media Converter is actively

sending or receiving data over that port.

Rear Panel
The rear panel of the XT-715A consists of one DC jack, which accepts input power with 5V DC, 2A.

Power Information

• The central pole of the Media Converter’s power jacks measures 2.5mm wide that requires +5VDC power input. It conforms to the bundled AC-DC adapter and PLANET’s media chassis. Should you have the issue of power connection, please contact your local sales representative.
• Please keep the AC-DC adapter as a spare part when the XT-715A is installed in a media chassis.
• Before installing the media converter into the converter slot of PLANET media converter chassis, please remove the earth grounding screw first.

DC receptacle is 2.5mm wide that matches the central pole; the width of the Media Converter DC jack also measures 2.5mm.
Warning: Do not install any improper unit.

The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.
In some areas, installing a surge suppression device may also help to protect your Media Converter from being damaged by unregulated surge or current to the converter or the power adapter.

Installation

• This section describes the functionalities of the Media Converter’s components and guides you to how to install it on the desktop.
• Basic knowledge of networking is assumed.
• Please read this chapter completely before continuing.

Stand-alone Installation

• Step 1: Unpack the Media Converter.
• Step 2: Connect the 5V DC power adapter to the XT-715A and verify that the Power LED lights up. (Please refer to the 2.4 Power Information section for power input.)
• Step 3: 3-1: Prepare a twisted-pair, straight-through Category 5e/6/7 UTP cable for Ethernet connection.
• 3- 2: Prepare a fiber cable for connection to the 10GBASE-X SFP+ slot, and make sure both sides of the SFP transceiver are with the same media type. (Please refer to the 3.5 Cable Connection section for the type of connection.)

NOTE:  After RJ45 port is connected, install 10G SFP+ transceiver; the RJ45 port LNK/ACT LED will light off and on upon the re-negotiation.

• Step 4: 4-1: Insert one side of Category 5e/6/7 cable into the Media Converter Ethernet port (RJ45) while the other side of Category 5e/6/7 cable into the network devices’ Ethernet port (RJ45), e.g., switch, PC or server.
  The UTP port (RJ45) LED on the Media Converter will light up when the cable is connected with the network device. (Please refer to the 2.2 LED Indicators section for the functions of LED lights.)

• 4-2: Connect the fiber cable. Attach the duplex LC connector on the network cable to the SFP+ transceiver. Attach the fiber cable from the XT-715A to the fiber network. TX, RX must be paired at both ends.

• Step 5: When all the connections are all set and the LED lights all show normal, the installation is completed.

1. Install the 10G SFP+ transceiver into the media converter 10G SFP+ slot; the 10G SFP+ slot LNK/ACT LED will light on (Chipset restriction).
2. The media converter 10G SFP+ slot will work after the 10G RJ45 port has been successfully connected.

Wall-mount Installation

• Step 1: Please find the wall that can mount the Media Converter.

• Step 2: Screw two screws on the wall.

• Step 3: Hang the Media Converter on the screws from the wall.

• Step 4: Refer to Chapter 2.4 Power Information on power supply to the Media Converter.

Before mounting the device to the wall, please check the location of the electrical outlet and the length of the Ethernet cable.

Media Chassis Installation

To install the Media Converter in a 10-inch or 19-inch standard rack, follow the instructions described below.

• Step 1: Place your Media Converter on a hard flat surface, with the front panel positioned towards your front side.
• Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis; the Power LED of the Media Converter will turn ON.

CAUTION

1. Before installing the media converter into the converter slot of PLANET media converter chassis, please remove the earth grounding screw first.
2. Never push the converter into the slot with force; it could damage the chassis.
3. The Media Converter Chassis supports hot-swap; there is no need to turn off the whole chassis before sliding in the new converter.

Optional DIN-rail Installation

There are two DIN-rail holes on the left side of the XT-715A that allows to be easily installed by DIN-rail mounting. PLANET optional DIN-rail mounting kit – RKE-DIN — can be ordered separately. Refer to the following steps for the DIN- rail mounting of the XT-715A:

• Step 1: Screw the DIN rail on the XT-715A.
• Step 2: Now slide the DIN rail into the track.
• Step 3: Check whether the DIN rail is tightly on the track.

CAUTION: You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would invalidate your warranty.

Cable Connection

Installing the SFP+ Transceiver\

• The sections describe how to insert an SFP+ transceiver into an SFP+ slot.
• The SFP+ transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP+ port without having to power down the Media Converter

It is recommended to use PLANET SFP+ transceiver on the Media Converter. If you insert an SFP+ transceiver that is not supported, the Media Converter will not recognize it.

10GBASE-X SR/LR:
Before connecting the other switches, workstation or Media Converter, please do the following:

1. Make sure both sides of the SFP+ transceiver are with the same media type; for example, 10GBASE-SR to 10GBASE-SR, 10GBASE-LR to 10GBASELR.
2. Check whether the fiber-optic cable type matches the SFP+ transceiver model.

• To connect to 10GBASE-SR SFP+ transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type.
• To connect to 10GBASE-LR SFP+ transceiver, use the single-mode fiber cable with one side being the male duplex LC connector type.

Connecting the fiber cable

1. Attach the duplex LC connector of the network cable to the SFP+ transceiver.
2. Connect the other end of the cable to a device like a switch with SFP+ installed, fiber NIC on a workstation or a Media Converter.

Removing the Transceiver Module

1. Make sure there is no network activity by consulting or checking with the network administrator. Or through the management interface of the switch/ converter (if available), disable the port in advance.
2. Remove the fiber optic cable gently.
3. Turn the lever of the MTB module to a horizontal position.
4. Pull out the module gently through the lever.

Never pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with effort could damage the module and SFP+ module slot of the Media Converter.

2.5G/5G/10GBASE-T
The 2.5G/5G/10GBASE-T port comes with auto-negotiation capability. It automatically supports 2.5GBASE-T, 5GBASE-T and 10GBASE-T networks. Users only need to plug a working network device into the 2.5G/5G/10GBASE-T port, and then turn on the Media Converter. The port will automatically run at 2500Mbps,5000Mbps and 10000Mbps after the negotiation with the connected device.
Connecting the UTP Cable
The 2.5G/5G/10GBASE-T port uses RJ45 socket — similar to phone jack — for connection of unshielded twisted-pair cable (UTP). The IEEE 802.3bz/802.3an Ethernet standard requires Category 5e UTP while 2.5G/5G/10GBASE-T uses Cat5e/6/6A/7 UTP (see table below). Maximum distance is 100 meters (328 feet).

NOTE: Be sure the connected network devices support MDI/MDI-X. If it does not support, then use the crossover Category 5e/6/6A/7 cable.

APPENDIX A: Approved PLANET SFP+ Transceivers

PLANET Media Converter supports 10GBASE-X with both multi-mode and single mode SFP+ transceivers. The following list of approved PLANET SFP+ transceivers are correct at the time of publication:
Available 10Gbps SFP+ Transceivers

MTB-LA10

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 10km (TX:1270nm RX:1330nm)

MTB-LB10

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 10km (TX:1330nm RX:1270nm)

MTB-LA20

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 20km (TX:1270nm RX:1330nm)

MTB-LB20

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 20km (TX:1330nm RX:1270nm)

MTB-LA40

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 40km (TX:1270nm RX:1330nm)

MTB-LB40

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 40km (TX:1330nm RX:1270nm)

MTB-LA60

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 60km (TX:1270nm RX:1330nm)
---|---

MTB-LB60

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 60km (TX:1330nm RX:1270nm)

MTB-LA70

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 70km (TX:1270nm RX:1330nm)

MTB-LB70

| 1-Port 10GBASE-BX SFP+ Fiber Optic Module – 70km (TX:1330nm RX:1270nm)

APPENDIX B: Networking Connection

B.1 Media Converter’s RJ45 Pin Assignments
2.5G, 5G and 10GBASE-T

B.2 RJ45 Cable Pin Assignments

The standard RJ45 receptacle/connector

• There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
• The following shows the pin allocation and color of straight cable and crossover cable connection:

Please make sure your connected cables are with the same pin assignment and color as the above diagram before deploying the cables into your network.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>