Planet Technology IPOE-175 Industrial IP67 1-Port 60W 802.3bt PoE++ Injector User Manual

Planet Technology IPOE-175 Industrial IP67 1-Port 60W 802.3bt PoE++

Injector User Manual

1. Package Contents

Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000/2500T 802.3bt PoE++ Injector, IPOE-175. In the following sections, the term “Outdoor PoE Injector” means the IPOE-175.

Open the box of the Industrial Ethernet Switch and carefully unpack it. The box should contain the following items:

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Remarks: The color of the ground wire is different according to the batch, but its wire specifications meet the standard.

2. Hardware Introduction

This section describes the functionalities of the outdoor PoE Injector’s components.

2.1 Product Outlook

Figure 2-1: IPOE-175 product outlook

2.2 Power Input Port
Figure 2-2 shows the power input port side of the IPOE-175

Figure 2-2: Power Input Port

2.3 Data Input Port and 802.3bt PoE++ Output Port
Figure 2-3 shows the data input port and PoE++ output port side of the IPOE- 175.

2.4 LED Indicators

Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug them into the Wall-mount Gigabit Ethernet Router

1. The wire gauge should be in the range from 20 to 22 AWG.
2. The device must be grounded.

3. Installation

This section describes how to install the Outdoor PoE Injector and make connections to it. Please read the following topics and perform the procedure in the order being presented.

3.1 Installing Cable Gland with Power Cable and RJ45 UTP Cable
The cable gland consists of the following:

3.2 Connecting Waterproof Cable Kit to the Outdoor PoE Injector
Step 1: Turn clockwise to tighten the gland body connected to the Outdoor PoE Injector.

Step 2: Plug the power cable connector into the power input port.

Step 3: Insert the sealing insert into the cable gland body.

Step 4: Attach the clamping nut to the cable gland to complete the cable assembly.

CAUTION: Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly.

Step 5: Repeat Steps 1 to 4 for “Data” Input Port and“PoE (Data + Power)” Output Port.

1. Use only the waterproof cable gland provided in the package of the IPOE-175.
2. If the above installation procedure is not properly followed, the warranty will be invalidated.
3. If the waterproof cable gland is found missing or damage, please contact your local reseller where you purchased from.
4. Never use any waterproof cable gland that is not purchased  from PLANET or doesn’t have the same dimensions of the IPOE-175; it will damage the device permanently.

3.3 Wall-mount Installation
To install the Outdoor PoE Injector on the wall, please follow the instructions described below.
Step 1: Find the wall that you want to mount the Outdoor PoE Injector on.
Step 2: Refer to the picture below to screw the four screws on the wall

Step3: Use a screwdriver to screw them into the wall.

3.4 Connecting IPOE-175 to PD
Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device.

NOTE: EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

3.5 Connecting IPOE-175 to PD
Step 1: Connect the additional Cat5e/6/6A cable from the PoE++ Out of the IPOE-175 to a remote PD.

Step 2: The PoE++ Out port is the power injector which transmits DC voltage to the Cat5e/6/6A cable and transfer data from the Data source.

Step 3: Once the IPOE-175 detects the existence of an IEEE 802.3at/bt device or Ethernet device, the LAN LED indicator will be lit steadily, showing it is providing power.

NOTE: According to IEEE 802.3at/bt standard, the IPOE-175 will not inject power to the cable if not connected to a standard IEEE 802.3at/bt device.

4. Product Specifications

NOTE: The PoE power output ability will depend on the distance.

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource and user’s manual on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.

PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address:
support@planet.com.tw

Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>