JLab Audio 2AHYVEPLEDG Work Buds In Ear Headset Instruction Manual

JLab Audio 2AHYVEPLEDG Work Buds In-Ear Headset

Product Information and Safety Instructions

Caution: ESD Precautions

To avoid damaging the unit by static electricity, ground yourself at all times when handling the unit. The unit is shipped with both ESD protective caps attached. These must be left on until the unit is ready to be installed into a system. The protective caps should be replaced whenever the unit is removed from the system for any reason.

Government/Industry Canada

This Class B digital device complies with Canadian ICES-003.

European Community Compliance Statement

This product conforms with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. The manufacturer cannot accept responsibility for any interference or the correction of interference installed by a third party. We have made every reasonable attempt to ensure the compliance of this product; however, the equipment must be used correctly to minimize potential interference. In case of such interference during the installation of this product, the responsibility rests with the installer to correct the problem by one or more of the following measures:

• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Compliance Statement

This product has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Japanese EMI Statement

This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If you are not sure of the type of power available, consult your dealer or local power company.

Specifications

CE Compliance Information and Statement for European Union Countries

If the product generates undue interference, you may try the following:

• Move your unit away from the interference, or
• Re-route your cabling away from the interference, or
• Turn off power to the interfering device(s) temporarily to prove compliance.

Information on Waste Electrical and Electronic Equipment (WEEE)

This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Instructions for Use, Removal, Recycling, and Disposal

To remove the batteries from your equipment for recycling, remove the two screws and the cover for the batteries. After removal of the cover, proceed to remove the batteries in the reverse order of the installation. For more information on how to dispose of the used batteries, refer to the recycling of rechargeable batteries and the recycling of used batteries in this manual. If the battery incorporated in your product becomes necessary to replace, see the user’s manual for information. If your household waste disposal service uses a separate collection system for batteries, please comply with it.

FAQ

What should I do if I experience interference with my device?

• You may try to re-orient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment to an outlet on a different circuit, or consult an experienced radio/TV technician for help.

How can I dispose of my electronic waste correctly?

• It should be handed over to an authorized collection site for recycling waste electrical and electronic equipment (EEE). Contact your local city office, household waste disposal service, or the place of purchase for more information.

What is the power source specification for this device?

• The input power source is 100-240V, 50/60 Hz, 1.5A, with an output of 5-6V, 4.0A.
• This transcription has been provided to ensure that all details from the original document are preserved and accessible for visually impaired users.
• The text has been structured into an HTML format for easier navigation and reading with the help of assistive technologies.

FCC Statement

Caution FCC Statement for Users

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

If you cannot eliminate the interference, the FCC requires that you stop using your product. Changes or Modifications not expressly by the party responsible for compliance could void the user’s authority to operate the equipment.

CAN ICES-003(B)/NMB-003(B)

This device contains license-exempt transmitters)/receivers) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(S).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure Information and Statement for Dongle:

This equipment complies with FCC/IC RSS- 102 radiation exposure limits set forth for an uncontrolled environment.

RF Exposure Information and Statement for TWS Earbuds:

• The SAR limit of Canada (C) is 1.6 W/kg averaging over one gram of tissue.
• Device types: (21316-EPICLE) has also been tested against this SAR limit According to this standard, the highest SAR value reported during product certification for head use is 0.413 W / kg.
• The device was tested for typical operations where the product was kept 0 mm from the head. To maintain compliance with IC RF exposure requirements, use accessories that maintain a separation distance of 0mm between the user’s head and the back of the headset. The use of belt clips, holsters, and similar accessories shall not contain metal parts in its assembly. The use of accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided.

Frequency Range

• 2402 MHz –
  • 2480 MHz
• SAR limits are used against the head. The SAR limit is 1.6 watts per kilogram averaging over 1 gram of tissue for use against the head. The SAR limit of USA (FCC) for head is 1.6 W/kg. The evaluation distance is 0 mm. The highest reported SAR is 0.41 W/kg.

Instructions for Users on Removal, Recycling, and Disposal of Used Batteries

• To remove the batteries from your equipment or remote control, reverse the procedure described in the owner’s manual for inserting batteries. For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. If, for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers.
• In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner. Contact your local waste-management officials for information regarding the environmentally sound collection, recycling, and disposal of used batteries.
• WARNING: Danger of explosion if battery is incorrectly replaced. To reduce the risk of fire or burns, don’t disassemble, crush, puncture, short external contacts, expose to temperature above 60 C (140 F), or dispose of in fire or water.
• Replace only with specified batteries. The symbol indicating separate collection’ for all batteries and accumulators shall be the crossed-out wheeled bin shown below:
• FCC ID: 2AHYV-EPICLE
• HVIN: Epic Lab Edition L
• HVIN: Epic Lab Edition R
• IC: 21316-EPICLE
• FCC ID: 2AHYV-EPLEDG
• IC: 21316-EPLEDG
• HVIN: Epic Lab Edition-Dongle

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>