JLAB AUDIO STUDIOPRO Wireless Over Ear Headphones User Guide
- July 3, 2024
- JLab Audio
Table of Contents
STUDIOPRO Wireless Over Ear Headphones
QUICK START GUIDE
PAIR UP
GET CHARGED
GO AHEAD, PRESS THE BUTTON
BLUETOOTH MULTIPOINT (Connect 2 devices simultaneously}
-
Once FIRST device is connected, tum off Bluetooth in device settings.
Studio Pro+ will auto enter Bluetooth Pairing. -
Enter your SECOND device Bivatooth settings and connect to Studio Pros.
-
Enter your FIRST device settings.
Tum oan Bluetooth and reconnect to Studio Pro+.
SHARE MODE (Share between two Studio Pro+ headphones)
Caution FCC Statement for Users
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
If you cannot eliminate the interference, the FCC requires that you stop using your product. Changes or Modifications not expressly by the party responsible for compliance could void the user’s authority to operate the equipment.
ECC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
CAN ICES-003(B)/NMB-003(B)
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- (1) this device may not cause harmful interference
- (2) this device must accept any interference received, including interference that may cause undesired operation.
ISED RSS-102 Radiation Exposure Statement
This equipment complies with ISED RSS-102 radiation exposure limits set
forth for an uncontrolled environment.
SAR Rating
Bluetooth Transmitter Power max: 12.5 dBm (18 mW)
Frequency Range
2402 MHz – 2480 MHz
Instructions for Users on Removal, Recycling and Disposal of Used Batteries
To remove the batteries from your equipment or remote control, reverse the
procedure described in the owner’s manual for inserting batteries. For
products with a built-in battery that lasts for the lifetime of the product,
removal may not be possible for the user. In this case, recycling or recovery
centers handle the dismantling of the product and the removal of the battery.
If, for any reason, it becomes necessary to replace such a battery, this
procedure must be performed by authorized service centers. In the European
Union and other locations, it is illegal to dispose of any battery with
household trash. All batteries must be disposed of in an environmentally sound
manner. Contact your local waste-management officials for information
regarding the environmentally sound collection, recycling and disposal of
used batteries.
WARNING: Danger of explosion if battery is incorrectly replaced. To
reduce risk of fire or burns, don’t disassemble, crush, puncture, short
external contacts, expose to temperature above 60 C (140 F), or dispose of in
fire or water. Replace only with specified batteries. The symbol indicating
‘separate collection’ for all batteries and accumulators shall be the crossed-
out wheeled bin shown below:
WELCOME TO THE LAB
The Lab is where you’ll find real people, developing really great products, in
a real place called San Diego.
PERSONAL TECH DONE BETTER
Designed for You
We actually listen to what you want and we’re always looking for ways to make
everything easier and better for you.
Lab Quality Sound
Choose from different settings and customize your sound style to match exactly
what you’re doing.
Surprisingly Awesome Value
We always pack in the most functionality and fun into every product at a truly
accessible price.
#yourkindof tech
Tech all about you
WITH LOVE FROM THE LAB
We have lots of different ways to show we care.
GET STARTED + FREE GIFT
Product updates How-to tips FAQs & more
Go to jlab.com/register to unlock your customer
benefits including a free gift. Gift for US only. No APO/FPO/DPO addresses.
WE GOT YOUR RACK
We’re obsessed with creating the best possible experience around owning our
products. If you have any questions, concerns, or feedback, we’re here for
you.
Contact a real human on our U.S.-based customer support team:
Website: jlab.com/contact
Email: support@jlab.com
Phone U.S.: +1 405-445-7219 (Check
hours jlab.com/hours)
Phone U.K./EU: +44 (20) 8142 9361 (Check hours
jlab.com/hours)
Visit jlab.com/warranty to initiate a return or
exchange.
LATEST AND GREATEST
Our team is constantly improving your product experience. This model may have
new features or controls which are not detailed in this guide.
For the latest version of the manual, scan the QR code below.
FCC ID: 2AHYV-SPPLUS
IC: 21316-SPPLUS
Complies with
IMDA Standards
DA00006A
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>