Jlab Audio JBuds Air Sport True Wireless Earbuds User Manual
- June 5, 2024
- JLab Audio
Table of Contents
Jlab Audio JBuds Air Sport True Wireless Earbuds
FIRST TIME SETUP
AUTO-CONNECTING EARBUDS
A. Take earbuds out of the charging case and remove stickers.
B. Press and hold both touch sensors 3+ seconds to turn ON. Left earbud
turns solid white and Right earbud blinks blue/white indicating ready to pair
to your device.
CONNECTING TO BLUETOOTH
Select “JLab JBuds Air Sport” in your device settings. Voice prompt “Bluetooth
connected” followed by solid white lights will indicate you are connected.
ADDING NEW / ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON
Bluetooth from new device. Take earbuds out of the case.
Earbuds will automatically enter Bluetooth Pairing. Select “JLab JBuds Air
Sport” in device settings to connect.
IN THE BOX
EARBUDS
EARTIPS
CHARGING CASE
BUTTON FUNCTIONS
VOLUME DOWN: Single tap
SIRI (iOS) or “OK GOOGLE” (ANDROID): Double tap
TRACK BACK: Press & hold 1+ sec
EQ CHANGE: Triple tap. (JBuds Air Sport will cycle 3 EQ settings)
POWER ON: Press & hold 3+ sec| VOLUME UP: Single tap PLAY /
PAUSE: Double tap TRACK FORWARD: Press & hold 1+ sec ANSWER:
Single tap
HANG UP: Double tap
REJECT INCOMING CALLS: Press & hold 1+ sec
BE AWARE ON / OFF: Triple tap
POWER ON: Press & hold 3+ sec
---|---
VOICE PROMPTS
“Hello”: Power ON
“Earbuds joined”:
Earbuds paired to each other
“Ready to Pair”: JBuds Air Sport are
ready to pair to Bluetooth device
“Bluetooth Connected”:
Earbud is connected to device
“Battery Full”: 100-80%
“Battery Medium”: 80-20%
“Low Battery”: Less than 20%
When power decreases to 10%,
“Low Battery” will play
“Goodbye”: Power OFF
TURN OFF EARBUDS WITHOUT CHARGING THE CASE:
Enter your Bluetooth device settings and disconnect the JBuds Air Sport.
Earbuds will power OFF after 3 minutes.
EQUALIZER MODES
Triple tap left earbud for different EQ settings. Voice prompts will indicate EQ settings (JBuds Air Sport will cycle 3 EQ settings)
JLab SIGNATURE
JLab C3™ signature sound with amplified bass and vocals
BALANCED
Even sound with no additional enhancements
BASS BOOST
Amplified bass and sub-bass
CHARGING EARBUDS
-
Placing the earbuds in the charging case will power off earbuds and start charging. Blue lights indicate earbuds are charging and will turn off when fully charged.
-
When earbuds are taken out of the case, they will auto power on and reconnect to your device.
CHARGING CASE
Connect the JBuds Air Sport to computer or USB 5V 1A (or less) output device.
Lights pulse white when charging and turn solid white when fully charged.
FITTING
TROUBLESHOOTING
NO AUDIO IN LEFT EARBUD OR EARBUDS DISCONNECT FROM EACH OTHER (MANUAL RESET)
-
Enter your Bluetooth device settings and forget the JBuds Air Sport. Fig A
-
Open the charging case door and leave both earbuds inside. Starting with ONE earbud, quickly tap the touch sensor 4x times. Light will blink blue 4x times then turn solid blue. Leave the earbuds in the charging case. Fig C1
-
Repeat with the other earbud. Quickly quickly tap the touch sensor 4x times.
Light will blink blue 4x times then turn solid blue. Fig C2 -
Take both earbuds out of the charging case and keep them within 2 inches from ,each other. Wait for Left earbud to turn solid white and Right to blink blue/white. You are now ready to pair to your Bluetooth device.
BLUETOOTH DEVICE DOES NOT CONNECT/RECONNECT
- Enter your Bluetooth device settings and forget the JBuds Air Sport. Fig A
- Turn OFF then ON Bluetooth. Fig B
- Take the earbuds out of the case. Wait for Left to turn solid white and Right blinking blue/white.
- Select “JLab JBuds Air Sport” in device settings to reconnect.
|
Instructional videos at: JLABAUDIO.COM/MANUALS
- Enter your Bluetooth device settings and forget the JBuds Air Sport. Fig A
- Turn OFF then ON Bluetooth. Fig B
- Take the earbuds out of the case. Wait for Left to turn solid white and Right blinking blue/white.
- Select “JLab JBuds Air Sport” in device settings to reconnect.
QUICK TIPS
- The Bluetooth connection is established from the right earbud.
- For the most stable connection, keep the device near right hand side or in right pocket.
- If you prefer to wear only one earbud, you must wear the right earbud as this is the main earbud connected to Bluetooth.
- Choosing the correct ear tip makes a significant improvement in audio quality due to the proper seal for the driver. Test all ear tips for best results.
- Only ONE Bluetooth device can be connected at a time. Turn off
- Bluetooth on unwanted devices and turn on Bluetooth on chosen device to connect.
WARNING
Fully dry off the earbuds before placing in the charging case.
If the earbuds are damp or wet, this will cause damage to the charging case.
The warranty will be voided if the charging case shows damage by water/sweat.
CAUTIONS
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the earbuds.
- Wax may build up in the earbud tips, lowering the sound quality.
- Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
- If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
- If you experience regular discomfort while using this product, discontinue use and consult your physician.
- We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
Shop products | Product alerts | Burn-in your headphones
JLab Audio + Burn-in Tool
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FAQS
How do I turn on the earbuds for the first time setup?
Take earbuds out of the charging case and remove stickers. Press and hold both touch sensors 3+ seconds to turn ON.
How do I connect the earbuds to Bluetooth?
Select “JLab JBuds Air Sport” in your device settings. Voice prompt “Bluetooth connected” followed by solid white lights will indicate you are connected.
how do I add new or additional Bluetooth devices?
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth from new device. Take earbuds out of the case. Earbuds will automatically enter Bluetooth Pairing. Select “JLab JBuds Air Sport” in device settings to connect.
how do I change the EQ settings?
Triple tap left earbud for different EQ settings. Voice prompts will indicate EQ settings (JBuds Air Sport will cycle 3 EQ settings).
how do I charge the earbuds?
Placing the earbuds in the charging case will power off earbuds and start charging. Blue lights indicate earbuds are charging and will turn off when fully charged.
How do I reset the earbuds if there is no audio in left earbud or earbuds disconnect from each other?
Enter your Bluetooth device settings and forget the JBuds Air Sport. Open the charging case door and leave both earbuds inside. Starting with ONE earbud, quickly tap the touch sensor 4x times. Light will blink blue 4x times then turn solid blue. Leave the earbuds in the charging case. Repeat with the other earbud. Quickly tap the touch sensor 4x times. Light will blink blue 4x times then turn solid blue. Take both earbuds out of the charging case and keep them within 2 inches from each other. Wait for Left earbud to turn solid white and Right to blink blue/white. You are now ready to pair to your Bluetooth device.
How do I disconnect the earbuds without using the charging case?
Enter your Bluetooth device settings and disconnect the JBuds Air Sport. Earbuds will power OFF after 3 minutes.
How do I know if the earbuds are fully charged?
Lights pulse white when charging and turn solid white when fully charged.
Can I connect more than one Bluetooth device at a time?
Only ONE Bluetooth device can be connected at a time. Turn off Bluetooth on unwanted devices and turn on Bluetooth on chosen device to connect.
How do I improve the audio quality?
Choosing the correct ear tip makes a significant improvement in audio quality due to the proper seal for the driver. Test all ear tips for best results. Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
What should I do if I experience discomfort or pain while using the earbuds?
Try lowering the volume or discontinuing use temporarily. If you experience regular discomfort while using this product, discontinue use and consult your physician.
JBuds Air Family Overview by JLab-VIDEO
References
- JLab: True Wireless Headphones, Earbuds, Microphones, Personal Audio
- Contact Us – JLab
- JLab Product Manuals
- Register Your Product – JLab
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>