anslut 019947 LED Strip Instruction Manual

LED STRIP
Item no. 019947

OPERATING INSTRUCTIONS

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions)

Jula reserves the right to make changes.
For latest version of operating instructions, see www.jula.com

JULA AB, BOX 363, SE-532 24 SKARA
2022-03-01
© Jula AB

SAFETY INSTRUCTIONS

• Only intended for indoor use.
• Do not connect the light to the mains while it is still in the pack.
• Check that all electrical and connecting cables comply with the applicable regulations and that they are connected in accordance with the instructions.
• Never overload the mains. This can result in fire or a risk of electric shock.
• Keep out of the reach of children.
• Do not store the light in a damp or very cold/hot place, this can damage the electronics.
• The electronics in the light are sensitive to knocks and blows. Avoid dropping it.
• The light source in this light is not replaceable. When the light source is consumed the whole product must be discarded.
• If the external power cord or wires are damaged they must be replaced with an approved cord or wires from the manufacturer or a dealer approved by the manufacturer.
• Pay attention so that no concealed wires are damaged in connection with installation.
• Be careful not to damage the insulation on the wires during installation. Make sure that the wires do not come into contact with sharp edges. Damaged insulation can result in a risk of electric shock.
• Do not look directly into the light source.
• Do not connect together more lights than the transformer has the capacity to support.

WARNING!
New installations and extensions to existing installations should always be carried out by an authorized electrician. If you have the necessary experience and knowledge (otherwise contact an electrician), you can replace power switches and wall sockets, fit plugs, extension cords, and light sockets. Incorrect installation can result in fatal injury and the risk of fire.

SYMBOLS

| Read the instructions.
---|---
| Only intended for indoor use.
| Class III
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.

TECHNICAL DATA

DESCRIPTION

1. Transformer (sold separately)
2. Light (sold separately)
3. Power cord (sold separately)
4. In-line connector (sold separately)
5. Elbow connector (sold separately)
6. Power switch On/Off (sold separately)
7. IR sensor (sold separately)
8. Touch dimmer (sold separately)
9. Branch connector (sold separately)
   FIG. 1
   FIG. 2

INSTALLATION

Choose a suitable place for installation and check that the transformer cord is long enough to reach the power point.

1. Place the light holders against the underside of the top cupboard and mark out where to fit them. Predrill screw holes when necessary.

2. Screw on the light holders.
   FIG. 3

3. Put the light in the holders.

4. Connect any additional lights, power switch, dimmer etc. The power switch, dimmer, or IR sensor should always be installed first in the chain. Make sure the transformer is disconnected from the mains voltage during the installation.

5. Plug the transformer into the powerpoint.

MAX NUMBER OF LIGHTS PER TRANSFORMER

| Light
---|---
Transformer| 5 W| 7,5 W| 14 W
7 W / 24 V DC| 1| 0| 0
24 W / 24 V DC| 4| 3| 1
45 W / 24 V DC| 9| 6| 3
60 W / 24 V DC| 12| 8| 4

WARNING!
Do not connect together more lights than the transformer has the capacity to support. See rated output for transformer.

REMOVAL

FIG. 4
1. Unscrew the screws on the casing.
FIG. 5
2. Remove the screws.
FIG. 6
3. Take out the guide plate and light source.
FIG. 7
4. Light source for SLR test.
FIG. 8

Documents / Resources

| anslut 019947 LED Strip [pdf] Instruction Manual
019947, LED Strip, 019947 LED Strip, Strip
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>