eurowise Gen 1 Cayenne Touareg Tubular upper Installation Guide
- May 15, 2024
- eurowise
Table of Contents
eurowise Gen 1 Cayenne Touareg Tubular upper
Specifications
- Product: Gen 1 Cayenne / Touareg Tubular upper control arm
- Manufacturer: Eurowise
- Location: 440 Springbrook Road, Charlotte, NC 28217
- Contact: 704-559-8100
- Email: info@eurowise.com
- Website: www.eurowise.com
Front Air Strut Removal / Coil Spring Removal:
- Set the steering to straight ahead.
- Raise the vehicle.
- Remove the front wheels.
- Remove air line fitting from the air valve.
- Remove the lower shock-mounting bolt.
- Remove the upper ball joint from the spindle assembly.
- Remove the sway bar end link to shock mounting nut and bolt.
- Remove and disconnect the shock damper sensor wire.
- Disconnect the ride height sensor’s electrical plug.
- Lift hood and remove the three mounting bolts that secure the air strut’s upper mount. Remove plastic cover to gain access to the third bolt.
- Remove strut assembly from the vehicle.
New Control Arm Installation:
Air suspension vehicles and vehicles with headlight level arms that attach
to the arms are installed using tube clamp and ball socket and nut provided.
Position clamp in the same orientation as OEM and reattach the sensor arm.
FAQ
Q: How do I contact Eurowise for questions or concerns?
A: You can contact Eurowise at 440 Springbrook Road, Charlotte, NC 28217, call
704-559-8100, email
info@eurowise.com, or visit their website at
www.eurowise.com.
Gen 1 Cayenne / Touareg Tubular upper control arm install
GENERAL INFORMATION
Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement.
WARNING: Consult your vehicle owner’s manual, service manual, or car dealer
for the correct jacking points on your vehicle and for additional care, safety
and
maintenance instructions. Under no circumstances should any work be completed
underneath the vehicle if it is not adequately supported, as serious injuries
and death can occur.
FRONT AIR STRUT REMOVAL / COIL SPRING REMOVAL
-
Set the steering to straight ahead.
-
Raise the vehicle.
-
Remove the front wheels. (FIGURE 10-1)
-
Remove air line fitting from the air valve. (FIGURE 10-2)
-
5. Remove the lower shock-mounting bolt. (FIGURES 10-3, 10-4)
-
Remove the upper ball joint from the spindle assembly. (FIGURES 10-5, 10-6)
-
Remove the sway bar end link to shock mounting nut and bolt. (FIGURE 10-7)
-
Remove and disconnect the shock damper sensor wire. (FIGURE 10-8)
-
Disconnect the ride height sensor’s electrical plug. (FIGURE 10-9)
-
Lift hood and remove the three (3) mounting bolts that secure the air strut’s upper mount. Remove plastic cover to gain access to the third bolt. (FIGURES 10-10, 10-11)
-
Remove strut assembly from the vehicle. (FIGURE 10-12)
Reuse the OEM bolts to attach the new control arms
Air supension vehicles and vehicles with headlight level arms that attach to the arms are installed using tube clamp and ball socket and nut provided. Position clamp in same orientation as OEM and reattach the sensor arm.
IF YOU HAVE ANY QUESTIONS, COMMENTS, OR CONCERNS RELATED TO YOUR PRODUCT PLEASE CONTACT US!
440 SPRINGBROOK ROAD. CHARLOTTE, NC 28217 |
704-559-8100
INFO@EUROWISE.COM |
WWW.EUROWISE.COM |
SHOP.EUROWISE.COM
References
- Specializing in European Service, Performance and Fabrication – Eurowise Performance
- Eurowise Audi, BMW, Volkswagen, Mercedes, & Porsche Service
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>