element EV02AB12GY Turbo Swivel Vacuum User Guide
- June 4, 2024
- Element
Table of Contents
element EV02AB12GY Turbo Swivel Vacuum
WHAT’S INCLUDED IN THE BOX
- Enhanced pet hair tool
- Dust cup release
- Dust cup handle
- Dust cup lter lid
- Air outlet
- Wheel
- Nozzle
- Power on/o‘
- Hose handle
- Power cord
- Power cord wrap
- Hose holder
- Handle
- Tool holder
- 3-in-1 tool
Pet (H)airbrush Tool
It has an air-driven brush roll for cleaning pet hair from your upholstery,
auto interiors, and more.
3-IN-1 Crevice Tool
”e 3-in-1 accessory/crevice tool allows for vacuuming in narrow and hard-to-
reach places.
HOW TO ASSEMBLE YOUR VACUUM
Please Note:
Always remove the plug from the power socket before tting or removing
accessories. Ensure all ters are tted, and tted correctly before using.
Warning:
DO NOT plug in your vacuum cleaner until you have completely assembled it per
the following instructions and are familiar with all instructions and
operating procedures.
-
Remove the dust cup before installing the handle. Insert the handle into the vacuum body, then rotate the screw into body as shown.
IMPORTANT: The handle must be inserted first before re-placing the dust cup. -
Place the dust cup back onto the machine and push until it clicks into place.
-
Flip open the connector hose cover and insert the hose. Insert another end of the hose into the side of the unit and rotate clockwise to lock.
-
Insert the 3-in-1 tool into the onboard tool holder, as shown.
-
Install the pet tool holder by aligning one side of the holder with the guides. Once the guides are aligned in the guide slot, press until the other side locks into place.
-
Place the pet tool on the pet tool holder by aligning the bottom hook with the pet tool and then press into the holder.
OPERATION
- Rotate the power cord wrap to release the power cord. Plug in your machine.
- Step on the brush cover and pull back on handle, to engage for operation.
- Push ON/OFF button to switch on.
- The unit has ve height adjustments for different floor types, from hard floor to high pro le carpet. When adjusting the height of the unit, the machine must be in the upright position.
ACCESSORY OPERATION
- Remove hose handle from the hose socket. The hose handle can be used immediately or with the addition of attachments.
MAINTENANCE AND CARE
Cleaning brush roll
WARNING:
Turn off and unplug the vacuum cleaner before performing maintenance to the
vacuum cleaner.
- Carefully remove any string, hair or debris that may be wrapped around the brush roll.
- You can use a tool such as a small knife or scissors to carefully, without damaging the bristles, cut any build-up of hair or string wrapped around the rotating bristle brush.
Empty the dust cup and clean the dust cup filter
WARNING:
Turn off and unplug the vacuum cleaner before performing maintenance to the
vacuum cleaner.
- Press the dust cup release button to remove the dust cup.
- Hold the dust cup over the wastebasket and press the lever to release the bottom lid. Debris will empty.
- Close the bottom lid until it clicks.
- Open the dust cup lter lid, located on the top of the cup.
- Remove the pre-motor lter.
- Rinse the lter thoroughly in lukewarm water until the water runs clear.
- Lift out lter holder, pull off foam lter and shake off dust frequently. Every three months, rinse lters and dry thoroughly.
- Reinstall foam later, filter holder, and pre-motor later.
- DO NOT operate without later installed.
- DO NOT wash the dust cup in the dishwasher.
- DO NOT install later damp.
CAUTION: Do not turn the appliance on when the dust cup is removed.
- In order to keep the suction force optimized, the dust cup and filters must be cleaned regularly.
- Reassemble after cleaning
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>