PRIMY B0B41TTS9S Office Ergonomic Desk Chair Instruction Manual
- May 15, 2024
- Primy
Table of Contents
PR988-J
Assembly Instruction
B0B41TTS9S Office Ergonomic Desk Chair
After-Sales Phone Number: (+1) 5854012902
https://wa.me/qr/HLZX6B7YFNPQD1| 
Scan the QR code to
watch the installation video.
https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=218
---|---
After-Sales Phone Number: (+1)
5854012902
https://wa.me/qr/HLZX6B7YFNPQD1| 
installation video
https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=218
Accessories List
Notice [If any question, contact [email protected] / [email protected]]
- Do not stand on this chair or use the chair as a step ladder uses it as chair only. This chair is designed for one person to use at a time.
- Do not use this chair unless all bolts, screws and knobs are firmly secured.
- Check all bolts, screws and knobs every 90 days. If the screws are loose, tighten them with a wrench.
- Failure to follow these instructions may result in serious injury of yourself and people around you.
- Some of the part are heavy and has shaped edge, please install it carefully to avoid hurting you and people around you.
Instructions for Use
Thanks for purchasing our products. Please read this manual before assembly.
And please assemble in order. After the assembly, keep the instruction
properly.
Make sure all the parts are included (18 kinds in total).
Assembly Instruction
Please assemble in a wide and flat place.
Take out Split Base Tube (G) and Central Base Tube (F). Insert Split Base Tube (G) into Central Base Tube (F) as shown. You can see in the Split Base Tube (G) and Central Base Tube (F) each have a screw hole, align them and tighten the 5 Screws M6X18mm (L) with Wrench (Q) to fix 5 Split Base Tubes (G) to Central Base Tube (F).
Take out 5 Casters (H), firmly insert them vertically into the hole of the Split Base Tube (G) as shown.
Take out Gas Lift (E), insert it into the hole of Central Base Tube (F) as
shown. Put it aside and we’ll use it in Step 8.
Take the Wrench (Q), assemble the Backrest (B) and Keel (J) with 3 Screws (M6X20mm) (O), then cover the screws with the Decorative Cover (K).
After step 4, take out the Base Plate (I), and connect it to the Keel (J) with 3 Screws (M8X35mm) (N) together as shown in the picture.
Then fix the bottom of Armrests (D) to the back of Seat Cushion (C). Tighten
the 6 Screws (M6X30mm) (M) with Wrench (Q) firmly.
* Caution: There is a “FRONT” sticker on the Seat Cushion (C). The right
armrest is engraved with the “R” logo, and the “L” logo is the left armrest,
please install the armrest correctly.
After step 6, connect the Seat Cushion (C) to the Base Plate (I) with 4 Screws (M6X18mm) (P).
Finally, align the holes in the Base Plate (I) with the Gas Lift (E) assembled
in step 3.
Next insert the Headrest (A) and Hanger (R) vertically into the hanger rest on
the Backrest (B).
Activate Your Warranty Now!
We guarantee you a pleasant buying experience. Please scan the QR code to activate your warranty so that you can enjoy priority and better after-sales service.
https://aftersale.qingtong123.com/landingpage/index.html?landing_page_id=218