BRAYER BR4971 Fan Instruction Manual
- June 9, 2024
- BRAYER
Table of Contents
BR4971 Fan
Instruction Manual
+7(495) 297-50- 20
info@brayer.su
brayer.su
The fan is intended for artificial ventilation of the room.
DESCRIPTION
-
Base
-
Pole
-
Control panel
-
Front grid
-
Blade lock
-
Blades
-
Rear grid fastening nut
-
Rear grid
-
Motor axis
-
Carrying handle
-
Body
-
Fan clamp on the stand
-
Flat washer
-
Base lock
Control panel (3) -
Body oscillation mode on/off button « »
-
On/off button « »
-
Air flow type selection button « »
-
Display
-
Airflow speed selection button « »
-
Timer On/Off button « »
Remote control (21) -
Remote control
-
Fan on/off button «ON.OFF»
-
Air flow speed selection button «SPEED»
-
Air flow type selection button «AIR FLOW»
-
Body oscillation on/off button «OSC»
-
Timer on/off button «TIMER»
-
Battery compartment lid
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation manual carefully before using the fan; after reading, keep it for future reference.
-
Use the unit for its intended purpose only, as it is stated in this manual.
-
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
-
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
-
Place the fan vertically on a flat dry moisture- and heat-resistant surface, do not place it horizontally and do not turn it over.
-
Do not place the fan on soft surfaces, such as carpets with high pile, sofas or beds.
-
Do not place the fan near curtains and do not direct it to house plants.
-
Do not use the fan in a limited space, for example, in built-in cabinets or wall niches.
-
It is not recommended to stay in the zone of the air flow from the fan for a long period of time, especially for children and the elderly.
-
Do not use the power cord as a carrying handle for the fan.
-
Do not wind the power cord around the fan body.
-
Provide that the power cord does not contact with hot surfaces and sharp furniture edges.
-
Protect the unit from impacts, falling, vibrations and other mechanical stress.
-
Avoid blocking the air inlet grid of the fan with foreign objects, do not cover the unit during the operation.
-
Do not use the unit in places where inflammable liquids are used or aerosols are sprayed, do not use the unit in the places where such liquids are stored.
-
Do not use the unit near heating appliances, heat sources or open flame.
-
Do not use the unit outdoors, in bathrooms or in places with high humidity.
-
Do not use the unit in proximity to the kitchen sink, near swimming pools or other containers filled with water.
-
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
-
Do not touch the unit body, the power cord and the power plug with wet hands.
-
It is not recommended to use the unit during lightning storms.
-
Do not block the airflow channel and do not insert any foreign objects into the channel.
-
Never leave the unit connected to the mains unattended.
-
Unplug the unit after usage or before cleaning.
-
Switch the fan off and unplug the power cord plug from the mains socket.
-
When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage or cause a short circuit.
-
Do not immerse the unit into water or any other liquids.
-
If water droplets fall on the fan body, switch it off and disconnect the power plug from the mains before touching the unit, then wipe the fan body with a dry cloth.
-
For child safety reasons do not leave polyethylene bags used as packaging unattended.
ATTENTION!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation! -
The unit is not intended for usage by children.
-
Do not leave children unattended to prevent using the unit as a toy.
-
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
-
Be especially careful if children or disabled persons are near the operating unit.
-
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
-
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
-
From time to time check the power cord integrity.
-
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
-
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
-
To avoid damages, transport the unit in the original package.
-
Keep the unit in a dry cool place out of reach of children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using it.
- Unpack the unit and remove all the packaging materials.
- Keep the original package.
- Read the safety measures and operating recommendations.
- Check the delivery set.
- Examine the unit for damages, in case of damage do not plug it into the mains.
- Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
- Wipe the fan body with a slightly damp cloth and then wipe it dry.
FAN ASSEMBLY
- Unscrew the base lock (14) from the stand (2) by rotating it counterclockwise (pic. 1).
- Install the base (1) on the stand (2), install the flat washer (13), screw the base lock (14) along the thread, rotating it clockwise (pic. 2).
- Unscrew the fan clamp (12) not completely by rotating it counterclockwise (pic. 3).
- Mount the fan body (11) onto the stand (2), screw in the fan clamp (12) by rotating it clockwise. When screwing the clamp (12) do not apply too much effort (pic. 3).
- Unscrew the blade lock (5) by turning it clockwise. Unscrew the rear grid fastening nut (7) by turning it counterclockwise (pic. 4)
- Match the guides on the motor unit with the corresponding openings on the grid (8) and install the rear grid (8) on the motor unit, fix it with the nut (7), turning it clockwise along the thread (pic. 5, 6).
- Install the blades (6) on the electric motor axis (9), and fix them with the lock (5), turning it counterclockwise along the thread, hold the blades (6) with your free hand (pic. 7, 8).
- Open the grid clamps, match the front (4) and rear (8) grids, close the clamps, make sure that the grids (4 and 8) are properly fixed (pic. 9, 10).
- Unscrew the fixing screw at the bottom part of the grid (pic. 11), set the clamp to the correct position (pic. 12), tighten the fixing screw (pic. 13).
Remote control (21)
-
Before using the remote control (RC) (21) open the battery compartment lid (27) and insert 2 «AA» batteries (supplied with the unit) into the battery compartment strictly following the polarity, close the battery compartment lid (27).
Note: if there is an isolating insert in the battery compartment, remove it. -
If you are not going to use the remote control for a long time, open the lid (27) and remove the batteries from the remote control (21) battery compartment.
-
Battery leakage may cause injury or damage to the remote control (21), to prevent damage to the remote control (21), follow the instructions below:
– use only the «AA» batteries;
– do not use old and new batteries at the same time;
– do not recharge the batteries;
– strictly observe the polarity while installing the batteries;
– take the batteries out if you are not going to use the remote control (21) for a long time;
– apply to specialized centers for recycling of the batteries. -
When you use the remote control, direct it to the front part of the fan body.
-
The distance between the remote control and the fan should not exceed 5 m, the coverage angle should be up to 30 degrees.
-
Avoid exposing the receiver to direct sunlight, otherwise false activation of control commands is possible.
USING THE FAN
- Place the fan base (1) on a flat, dry and steady surface.
- Do not place the fan on soft surfaces, such as carpets with high pile, sofas or beds.
- Plug the power cord into the mains socket, the on/off button indicator (16) will light up « ».
Switching the fan on/off and selecting the airflow speed
- To switch the fan on, press the button (16) « » on the control panel (3) or the button (22) «ON/OFF» on the remote control (21), you will hear a sound signal, and the fan will switch on at low airflow speed, the symbol «L1» will light up on the display (18).
- Pressing the button (19) « » on the control panel (3) or the button (23) «SPEED» on the remote control (21) you can select the air flow speed, the symbols (12) «L1, L2, L3» will appear on the display (18).
- To switch the fan off, press the button (16) « » on the control panel or the button (3) «ON/OFF» on the remote control (22). The fan will be switched off.
Fan operation time timer
- To set the fan operation time, press the button (20) « » on the control panel (3) or the button (26) «TIMER» on the remote control (21), the display (18) will show the operation time in digital symbols.
- Timer setting time from 1 hour to 12 hours, setting step 1 hour.
- To switch the timer off, press the button (20 or 26) repeatedly until the timer operation time digital symbols go out on the display (18).
Switching the fan body oscillation on/off
- To switch the fan body oscillation function on, press the button (15) « » on the control panel (3) or the button (25) «OSC» on the remote control (21), to switch the oscillation function off, press again the button (15) « » on the control panel (3) or the button (25) «OSC» on the remote control (21).
Note: you can change the direction of the airflow in the vertical plane,
the angle of change in the airflow direction is and is set manually.
Selecting the airflow type
-
Press the button (17) « » on the control panel (3) or the button (24) «AIR FLOW» on the remote control (21) to select the type of air flow, normal operation mode or night mode.
-
To switch the fan off, press the button (16) « » on the control panel (3) or the button (22) «ON/OFF» on the remote control (21). The fan will be switched off.
-
Remove the power plug from the mains socket.
Note: in the timer mode or the night mode, the symbols on the display (18) will go out after 10 seconds, to switch the display (18) on press any button. -
Carry the fan by the handle (10).
CLEANING AND MAINTENANCE
- Before cleaning the fan, switch it off and unplug it.
- Wipe the fan body with a slightly damp cloth and then wipe it dry.
- Do not use liquid detergents, abrasive cleaners and any solvents to clean the fan.
- To avoid the risk of electric shock, do not allow water or any other liquid to get inside the fan body (11) and the control panel (3).
- You can use the vacuum cleaner with a corresponding attachment to clean the rear (8) and front (4) grids.
STORAGE
- After cleaning put the fan away for storage in a dry cool place away from children and disabled persons.
- Remove the battery from the remote control (21) if you are not going to use it for a long time.
- Before using the fan next time, it is recommended to check the unit operability and integrity of the power cord isolation and the power cord plug.
DELIVERY SET
Fan — 1 pc.
Instruction manual — 1 pc.
Remote control — 1 pc.
TECHNICAL SPECIFICATIONS
- Power supply: 220-240 V, ~ 50/60 Hz
- Rated input power: 50 W
- Remote control: 3V – 2 elements «AA» (not included in the delivery)
RECYCLING
To prevent possible damage to the environment or harm to the health of people
by uncontrolled waste disposal, after service life expiration of the unit or
the batteries (if included), do not discard them with usual household waste,
deliver the unit and the batteries to specialized centers for further
recycling.
The waste generated during the disposal of the unit is subject to mandatory
collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local
municipal administration, a disposal service or to the shop where you
purchased this product.
The manufacturer reserves the right to change the appearance, design and
specifications not affecting general operation principles of the unit, without
prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions promptly apply to the authorized service
center.
Hergestellt für Ruste GmbH,
Berggasse 18/18, 1090 Wien,
Osterreich
Produced for Ruste GmbH,
Berggasse 18/18, 1090 Vienna, Austria
Authorized by the manufacturer person: Grantel LLC
143912, Moscow Region, Balashikha,
sh. Enthusiasts, ow. 1A
T.: +7 (495) 297-50-20,
E-mail: info@brayer.su
brayer.ru
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>