Primy 10000 Steel Voyage Medium Sand Instructions
- June 13, 2024
- Primy
Table of Contents
Primy 10000 Steel Voyage Medium Sand
Product Information
The product is a range of faucets with different models and variations. The product is available in various editions with different article numbers. The current edition is dated 2023-03-27. The product is designed for installation in porcelain and countertops with a thickness of up to 50 mm. The product comes with pre-assembled connecting hoses.
Product Usage Instructions
Before installation, it is important to turn off the water and flush the
piping carefully. Make sure that all components of the mixer are fitted
securely. Do not attempt to dismantle the components yourself. Check that the
pre-assembled connecting hoses are tightened securely. If you have any
questions or doubts, contact your retailer or a qualified plumber for
assistance.
In case of uneven or weak flow, unscrew the nozzle from the spout and remove
the small plastic insert (except for the STREAM model). Soak the insert in a
solution of 1 part vinegar and 3 parts hot water for at least an hour. Refer
to the corresponding diagram for your model.
If there is a risk of frost, turn off the water and drain the mixer completely
to prevent damage to the cartridge.
If the tap is dripping, the cartridge needs to be replaced. Refer to the
diagram on the next page that matches your model for instructions on how to
replace the cartridge.
Note : The specified torque for tightening is 2-3N.M for certain models.
Refer to the corresponding model numbers for this torque requirement.
ART. NO:
10000, 10006, 10007, 10008, 10015, 10016, 10017, 10018, 10020, 10028, 10060, 10068, 10070, 10078, 10080, 10200, 10206, 10207, 10208, 10215, 10216, 10217, 10218, 12200, 12201, 12202, 12215, 12216, 12217, 10230, 10236, 10237, 10238, 12230, 12231, 12232, 10240, 10246, 10247, 10248, 12240, 12241, 12242, 10220, 10226, 10227, 10228, 12220, 12221, 12222, 10300, 10301, 10210, 10211, 10212, 10213, 12005, 12006, 12007, 10250, 10256, 10257, 10258, 12250, 12251, 12252
RSK:
8344559, 8277584, 8277585, 8277783, 8344560, 8277586, 8277587, 8277784, 8344561, 8277820, 8344568, 8277821, 8344569, 8277822, 8344570, 8277855, 8277856, 8277857, 8277858, 8277859, 8277860, 8277861, 8277862, 8278135, 8278136, 8278133, 8278137, 8278138, 8278134, 8278227, 8278228, 8278229, 8278230, 8278231, 8278232, 8278233, 8278234, 8278235, 8278236, 8278237, 8278238, 8278239, 8278240, 8278241, 8278242, 8278243, 8278244, 8278245, 8278246, 8278247, 8278248, 8278249, 8275645, 8275646, 8275647, 8275648, 8275649, 8275650, 8275651, 8275652, 8275653, 8275654, 8275655, 8275656, 8275657, 8275658
Before installation
- Turn off the water. Flush piping carefully before installation. Check that the components of the mixer are fitted securely. Do not try to dismantle the components yourself. Check that the pre-assembled connecting hoses are tightened securely.
- Contact your retailer if you have any questions. Installation must be carried out by a competent per-son. If in doubt please contact a qualified plumber.
- All our products are tested and approved to EN standards: kitchen and basin mixers to EN 817, dual control mixers to EN 200 and thermostatic mixers to EN 1111. Tested and approved by SINTEF in accordance with relevant standards. Recommended working pressure 50-1,000 kPa (0.5–10 bar). Test pressure 1,600 kPa (16 bar). Water temperature min. 0 °C and max. 90 °C. Our mixers are made from grade 304 stainless steel, a material that can be fully recycled.
Models with hoses that are already fitted to the mixer.
Fit the components in place in the sequence shown in the drawings (1–6). Note!
Make sure the hole for the mixer has a diameter of 35 mm. Then connect the
hoses to the hot and cold water supplies. Make sure that the hoses are
connected to the correct water supply (blue hose to cold water and red hose to
hot water). Check that the connecting hoses are tightened securely. When the
mixer is fitted, check that all connections are secure. The mixer is connected
without support rings in the flexible hoses.
- A Mixer
- B Base
- C Base washer – placed in B
- D Threaded tube
- E Rubber washer
- F Steel washer
- G Easy-fix threaded coupler
Models with separate hoses
Fit the components in place in the sequence shown in the drawings (1–7). Note! Mount the blue and red marked hose with the same colors on the mixer body. The hoses are O-ring sealed and no other seal is needed. The hoses are threaded to the right and do not need to be lubricated. They must be installed by hand. Do not use tools. Note! Make sure the hole for the mixer has a diameter of 35 mm. Then connect the other ends of the hoses to the hot and cold water supplies. Make sure that the hoses are connected to the correct water supply (blue hose to cold water and red hose to hot water). Check that the connecting hoses are tightened securely. When the mixer is fitted, check that all connections are secure. The mixer is connected without support rings in the flexible hoses.
- A Mixer
- B Base
- C Base washer – placed in B
- D Threaded tube
- E Rubber washer
- F Steel washer
- G Easy-fix threaded coupler
- H Hoses
Troubleshooting
-
Uneven or weak flow:
Unscrew the nozzle from the spout and remove the small plastic insert (does not apply to STREAM). Soak it in a solution of 1 part vinegar and 3 parts hot water for at least an hour. See drawing that matches your model. -
In case of frost:
Turn off the water and drain the mixer completely of water. Otherwise there is a risk of damage to the cartridge. -
Dripping tap:
The cartridge must be replaced, see the diagram on the next page that matches your model.
Unscrew the nozzle
- Steel Clear 10020, 10028
- Steel Wave 10000, 10006, 10007, 10008, 10015, 10016, 10017, 10018, Steel Voyage 10200, 10206, 10207, 10208, 10210, 10211, 10212, 10213, 10215, 10216, 10217, 10218, Voyage 12200, 12201, 12202, 12005, 12006, 12007, 12215, 12216, 12217
- Steel Vertex 10220, 10226, 10227. 10228, Steel Vector 10230, 10236, 10237, 10238, 10240, 10246, 10247, 10248, Vertex 12220, 12221, 12222, Steel Vector 10230, 10236, 10237, 10238, 10240, 10246, 10247, 10248, 10250, 10256, 10257, 10258, Vector 12230, 12231, 12232, 12240, 12241, 12242, 12250, 12251, 12252
- Radian 10300, 10301
- Steel Speed 10060, 10068, Steel Pure 10070, 10078
Replace cartridge
- Steel Wave 10000, 10006, 10007, 10008, 10015, 10016, 10017, 10018 Steel Clear 10020, 10028
- Steel Stream 10080
- Steel Voyage 10200, 10206, 10207, 10208, 10210, 10211, 10212, 10213, 10215, 10216, 10217, 10218, Voyage 12200, 12201, 12202, 12005, 12006, 12007, 12215, 12216, 12217, Steel Vector 10230, 10236, 10237, 10238, 10240, 10246, 10247, 10248, 10250, 10256, 10257, 10258, Vector 12230, 12231, 12232, 12240, 12241, 12242, 12250, 12251, 12252, Steel Vertex 10220, 10226, 10227, 10228, 12220, 12221, 12222, Radian 10300, 10301, Steel Speed 10060, 10068, Steel Pure 10070, 10078
Information
Steel Stream 10080, Steel Voyage 10200, 10206, 10207, 10208, 10210, 10211, 10212, 10213, 10215, 10216, 10217, 10218, Voyage 12200, 12201, 12202, 12005, 12006, 12007, 12215, 12216, 12217, Steel Vector 10230, 10236, 10237, 10238, 10250, 10256, 10257, 10258, 10240, 10246, 10247, 10248, Vector 12230 12231, 12232, 12250, 12251, 12252 12240, 12241, 12242, Steel Vertex 10220, 10226, 10227, 10228, 12220, 12221, 12222, Radian 10300, 10301 are water-saving mixers.
Cleaning
If you have any other questions, please contact your retailer or
www.scandtap.com
Scandtap AB, Olofsdalsvägen 21, 302 41 Halmstad, Sweden+46 35 260 75 80,
info@scandtap.com,
www.scandtap.com
EDITION : 2023-03-27
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>